Effect of High-Strength Reinforcement Steel on Shear Friction Behavior
Publication: Journal of Bridge Engineering
Volume 22, Issue 8
Abstract
Current bridge provisions limit the contribution of the reinforcing steel in concrete shear interface design to a yield strength of 420 MPa (60 ksi). Because of this, the higher yield strength of high-strength steel (HSS) reinforcing bars cannot currently be used in design. Only a limited number of tests have been performed to characterize the shear friction resistance of members containing HSS, and results from these tests indicate that using the full HSS reinforcing bar yield stress capacity could overestimate the shear interface capacity of the specimens. However, shear friction design using HSS reinforcement at its yield strength, if shown viable, could provide constructability benefits. In this work, the effect of HSS reinforcement on concrete–concrete shear interface capacity is investigated. The specimens had varying reinforcing steel ratios (0.42 and 0.64%), bar sizes [#13M (#4) and #16M (#5)], and steel grades [Grade 420 (60 ksi) and Grade 550 (80 ksi)]. Four sets of five push-off test specimen types were tested for a total of 20 specimens. All push-off specimens were designed to have similar interface shear resistance using current design equations. Testing results indicate that although the peak strength capacity of the specimens reinforced with Grade 550 #16M (#5) bars was greater than that of the Grade 420 #16M (#5) bars, a similar increase was not observed in the #13M (#4) specimens in which negligible differences were observed in the peak strength. However, the use of HSS reinforcement increased the postpeak sustained loads.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2015). AASHTO LRFD bridge design specifications, customary U.S. units, Washington, DC.
ACI (American Concrete Institute). (2014). Building code requirements for structural concrete (ACI 318-14) and commentary, Farmington Hills, MI.
ASTM. (2012). “Standard test method for compressive strength of cylindrical concrete specimens.” C39/C39M, West Conshohocken, PA.
ASTM. (2013). “Standard test methods for tension testing of metallic materials.” E8/E8M, West Conshohocken, PA.
ASTM. (2014). “Standard specification for low-alloy steel deformed and plain bars for concrete reinforcement.” A706/A706M, West Conshohocken, PA.
ASTM. (2016a). “Standard specification for deformed and plain, low-carbon, chromium, steel bars for concrete reinforcement.” A1035/A1035M, West Conshocken, PA.
ASTM. (2016b). “Standard specification for deformed and plain carbon-steel bars for concrete reinforcement.” A615/A615M, West Conshocken, PA.
Barbosa, A. R., Link, T., and Trejo, D. (2015). “Seismic performance of high-strength steel RC bridge columns.” J. Bridge Eng., 04015044.
Barbosa, A. R., Trejo, D., and Nielson, D. (2017). “High strength reinforcing steel bars: Concrete shear friction interface.” SPR 762---Part A, Report no. FHWA-OR-RD-17-08, Oregon DOT, Salem, OR.
Caltrans. (1994). “Bridge design practice.” California DOT, Sacramento, CA.
Harries, K. A., Zeno, G. A., and Shahrooz, B. (2012). “Toward an improved understanding of shear-friction behavior.” ACI Struct. J., 109(6), 835–844.
Hofbeck, J. A., Ibrahim, I. O., and Mattock, A. H. (1969). “Shear transfer in reinforced concrete.” ACI J. Proc., 66(2), 119–128.
Júlio, E. N. B. S., Branco, F. A. B., and Silva, V. D. (2004). “Concrete-to-concrete bond strength. Influence of the roughness of the substrate surface.” Constr. Build. Mater., 18(9), 675–681.
Kahn, L. F., and Mitchell, A. D. (2002). “Shear friction tests with high-strength concrete.” ACI Struct. J., 99(1), 98–103.
Kahn, L. F., and Slapkus, A. (2004). “Interface shear in high strength composite T-beams.” PCI J., 49(4), 102–110.
Loov, R. E., and Patnaik, A. K. (1994). “Horizontal shear strength of composite concrete beams with a rough interface.” PCI J., 39(1), 48–69.
Mansur, M., Vinayagam, T., and Tan, K. (2008). “Shear transfer across a crack in reinforced high-strength concrete.” J. Mater. Civ. Eng., 294–302.
Mattock, A. H., Li, W. K., and Wang, T. C. (1976). “Shear transfer in lightweight reinforced concrete.” PCI J., 21(1), 20–39.
Mirza, S. A., Hatzinikolas, M., and MacGregor, J. G. (1979). “Statistical descriptions of strength of concrete.” J. Struct. Div., 105(6), 1021–1037.
Mirza, S. A., and MacGregor, J. G. (1979). “Variability of mechanical properties of reinforcing bars.” J. Struct. Div., 105(5), 921–937.
NCHRP (National Cooperative Highway Research Program). (2011). “Design of concrete structures using high-strength steel reinforcement.” Rep. 679, Washington, DC.
Park, P., and Paulay, T. (1975). Reinforced concrete structures, John Wiley & Sons, New York.
Patnaik, A. (2001). “Behavior of composite concrete beams with smooth interface.” J. Struct. Eng., 359–366.
Saemann, J. C., and Washa, G. W. (1964). “Horizontal shear connections between precast beams and cast-in-place.” ACI J. Proc., 61(11), 1383–1408.
Santos, P. M. D., and Júlio, E. N. B. S. (2012). “A state-of-the-art review on shear-friction.” Eng. Struct., 45(Dec), 435–448.
Scholz, D. P., Wallenfelsz, J. A., Cintia, L., and Roberts-Wollmann, C. A. (2007). “Recommendations for the connection between full-depth precast bridge deck panel systems and precast I-beams.” Final Rep. VTRC 07-CR17, Virginia Transportation Research Council, Charlottesville, VA.
Scott, J. (2010). “Interface shear strength in lightweight concrete bridge girders.” Master’s thesis, Virginia Tech, Blacksburg, VA.
Trejo, D., and Kim, Y. H. (2011). Development of precast bridge deck overhang system: Technical report, Texas Transportation Institute, Texas A&M Univ. System, College Station, TX.
Trejo, D., Link, T., and Barbosa, A. R. (2015). “Effect of reinforcement grade and ratio on seismic performance of RC columns.” ACI Struct. J., 113(5), 907–916.
Wallenfelsz, J. A. (2016). “Horizontal shear transfer for full-depth precast concrete bridge deck panels.” Master’s thesis, Virginia Tech, Blacksburg, VA.
Walraven, J. C., and Reinhardt, H. W. (1981). “Theory and experiments on the mechanical behaviour of cracks in plain and reinforced concrete subjected to shear loading.” HERON, 26(1A), 1–68.
Information & Authors
Information
Published In
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Nov 23, 2015
Accepted: Oct 11, 2016
Published online: May 23, 2017
Published in print: Aug 1, 2017
Discussion open until: Oct 23, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.