Investigation of the Effects of Transverse Bending in a Composite Inverted T-Slab Bridge System
Publication: Journal of Bridge Engineering
Volume 22, Issue 1
Abstract
The composite inverted T-slab bridge system provides an accelerated bridge construction alternative for short- to medium-span bridges with spans ranging from 6.1 to 20 m. The system consists of adjacent precast inverted T-slabs with a cast-in-place (CIP) concrete topping. Such a composite bridge system offers a shallow superstructure depth ideal for sites with stringent vertical clearance requirements. When concentrated loads are applied to a bridge of this type, the bridge deforms as a two-way flat plate. This paper presents an analytical and experimental investigation to study the relationship between transverse bending and reflective cracking. Transverse bending moment demands were quantified using a finite-element model and compared with tested transverse bending moment capacities provided by several subassemblage specimens, which feature two precast cross-sectional shapes and three transverse connections. It was concluded that all tested specimens performed well at service load levels. The detail that features a precast inverted T-slab with tapered webs and no mechanical connection between the adjacent inverted T-slabs and CIP topping is the simplest and most economical.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the guidance and assistance of Michael Brown of the Virginia Transportation Research Center, and Andy Zickler and Chris Lowe of the Structure and Bridge Division of the Virginia DOT. The assistance of Doug Nelson, David Mokarem, Brett Farmer, Dennis Huffman, and Kedar Halbe at the Murray Structural Engineering Laboratory at Virginia Tech is gratefully acknowledged. The opinions in this report are those of the authors and not necessarily those of the sponsor.
References
AASHTO. (2012). LRFD bridge design specifications, 6th Ed., Washington, DC.
ASTM. (2012a). “Standard specification for deformed and plain carbon-steel bars for concrete reinforcement.” A615M, West Conshohocken, PA.
ASTM. (2012b). “Standard specification for steel strand, uncoated Seven-wire for prestressed concrete.” A416M, West Conshohocken, PA.
Badwan, I., and Liang, R. Y. (2007). “Transverse post-tensioning design of precast concrete multibeam deck.” PCI J., 52(4), 84–92.
Bell, C., Shield, C. K., and French, C. W. (2006). “Application of precast decks and other elements to bridge structures.” MnDOT Tech. Rep. No. MN/RC 2006-37, Minnesota DOT, St. Paul, MN.
Dassault Systèmes SIMULIA. (2012). Abaqus, user’s manual version 6.11-2, Dassault Systèmes SIMULIA, Waltham, MA.
Dimaculangan, M. C., and Lesch, T., (2010). “Minnesota’s precast composite slab span system.” Aspire, 40–62.
El-Remaily, A., Tadros, M. K., Yamane, T., and Krause, G., (1996). “Transverse design of adjacent precast prestressed concrete box girder bridges.” PCI J., 41(4), 96–113.
French, C. W., et al. (2011). “Cast-in-place concrete connections for precast deck systems.” NCHRP 10–71, 173, National Cooperative Highway Research Program, Washington, DC.
Hagen, K., Ellis, S., Fishbein, J., Molnau, K., Wolhowe, E., and Dorgan, D. (2005). “Development and construction of a precast inverted t system for expediting Minnesota slab span bridge projects.” Proc., PCI 2005 National Bridge Conf., Precast Concrete Institute, Chicago, IL.
Halverson, M., French, C., and Shield, C. (2012). “Full-depth precast concrete bridge deck system: Phase II.” MnDOT Tech. Rep. No. MN/RC 2012-30, Minnesota DOT, St. Paul, MN.
Hanna, K. E., Morcous, G., and Tadros, M. K. (2009). “Transverse post-tensioning design and detailing of precast, prestressed concrete adjacent-box-girder bridges.” PCI J., 54(4), 160–174.
Huckelbridge, A. A., Jr., El-Esnawi, H., and Moses, F. (1995). “Shear key performance in multibeam box girder bridges.” J. Perform. Constr. Facil., 271–285.
Menkulasi, F., Nelson, D., Wollmann, C. L. R., and Cousins, T. (2015). “Reducing deck cracking in composite bridges by controlling shrinkage and creep properties.” ACI Spec. Publ., SP-304, 21–42.
Menkulasi, F., Wollmann, C. L. R., and Cousins, T. (2013). “Investigation of time dependent effects on composite bridges with precast inverted T-beams.” Proc., PCI 2013 National Bridge Conf., Precast Concrete Institute, Chicago, IL.
Miller, R. A., Hlavacs, G. M., Long, T., and Greuel, A. (1999). “Full-scale testing of shear keys for adjacent box girder bridges.” PCI J., 44(6), 80–90.
Ralls, M. L., et al. (2005). “Prefabricated bridge elements and systems in japan and Europe.” Rep. No. FHWA-PL-05-003, Federal Highway Administration, Washington, DC.
Smith, M., Erikkson, W., Shield, C., and French, C. (2007). “Field and laboratory study of the MnDOT precast slab span system.” Proc., 2007 Mid-Continent Transportation Research Symp., Iowa State Univ., Ames, IA.
Smith, M. J., Eriksson, W. D., Shield, C. K., and French, C. W. (2008). “Monitoring and analysis of Mn/DOT precast composite slab span system (PCSSS).” MnDOT Tech. Rep. No. MN/RC 2008-4, Minnesota DOT, St. Paul, MN.
VDOT (Virginia DOT). (2012). “Proposed bridge on Rte. 360 over Chickahominy River, Henrico Co. 0.3 mi. W. Hanover-Henrico Co. Line.” Project 0360-964-120, B607, Virginia DOT, Richmond, VA.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Feb 18, 2016
Accepted: Jun 17, 2016
Published online: Aug 30, 2016
Published in print: Jan 1, 2017
Discussion open until: Jan 30, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.