Full-Range S-N Fatigue-Life Evaluation Method for Welded Bridge Structures Considering Hot-Spot and Welding Residual Stress
Publication: Journal of Bridge Engineering
Volume 21, Issue 12
Abstract
Fatigue cracking is crucial issue for welded steel bridges that endure repeated vehicle loads. With typical fatigue-life evaluation methods, it is difficult to consider the influence of low stress amplitude. Based on existing full-range S-N curves and their formulas for base metal, a unified fatigue-life evaluation method is recommended for welded joints. The basis for construction of full-range S-N curves is to obtain the welding residual stress and stress concentration factor. In this paper, rib-to-deck welded joints are introduced as examples to demonstrate the detailed steps of a fatigue-life evaluation procedure. From the analysis of welding residual stress, it can be concluded that residual stress is influenced by the geometric dimensions of the composite members. With an increase in the geometric dimensions, the level of residual stress is increased. In addition, static-load experiments were conducted to obtain the stress concentration factor. A hot-spot full-range S-N curve was then obtained for rib-to-deck welded joints by calibrating the formula from small quantities of fatigue experiments. An actual bridge installed with a structural health monitoring system (SHMS) was used as a case study to compare the recommended model with typical fatigue codes. The comparison results indicate that the recommended model is more conservative than typical fatigue codes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the National Basic Research Program of China (973 Program, No. 2015CB060000), the National Science and Technology Support Program of China (No. 2014BAG07B01), the Key Program of the National Natural Science Foundation (No. 51438002), the Program of National Natural Science Foundation (No. 51578138, 51508251), the Natural Science Fund for Colleges and Universities in Jiangsu Province (No. 15KJB560005), the Fundamental Research Funds for the Central Universities and the Innovation Plan Program for Ordinary University Graduates of Jiangsu Province in 2014 (No. KYLX-0156), the Fundamental Research Funds for the Central Universities (No. 2242016K41066), the Jinling Institute of Technology High-Level Personnel Work Activation Fee to Fund Projects (No. jit-b-201614), and the Scientific Research Foundation of Graduate School of Southeast University (No. YBJJ1441).
References
AASHTO. (1990). Guide specifications for fatigue evaluation of existing steel bridges, Washington, DC.
Agerskov, H., and Nielsen, J. A. (1999). “Fatigue in steel highway bridges under random loading.” J. Struct. Div., 152–162.
ANSYS 15 [Computer software]. ANSYS, Canonsburg, PA.
Bandara, C. S., Siriwardane, S. C., Dissanayake, U. I., and Dissanayake, R. (2015). “Developing a full range S–N curve and estimating cumulative fatigue damage of steel elements.” Comput. Mater. Sci., 96, 96–101.
BSI (British Standards Institution). (1980). BS 5400: Steel, concrete and composite bridges—Part 10: Code of practice for fatigue, London.
CEN (European Committee for Standardization). (1992). “Design of steel structures, Part 1–9: Fatigue.” Eurocode 3, Brussels, Belgium.
Chakraborty, S., and Dewolf, J. T. (2006). “Development and implementation of a continuous strain monitoring system on a multi-girder composite steel bridge.” J. Bridge Eng., 753–762.
Chen, Z. W., Xu, Y. L., and Wang, X. M. (2012). “SHMS-based fatigue reliability analysis of multiloading suspension bridges.” J. Bridge Eng., 299–307.
Cremona, C., Eichler, B., Johansson, B., and Larsson, T. (2013). “Improved assessment methods for static and fatigue resistance of old metallic railway bridges.” J. Bridge Eng., 1164–1173.
Fisher, J. W. (1984). Fatigue and fracture in steel bridges: Case studies, John Wiley & Sons, New York.
Frangopol, D. M., Strauss, A., and Kim, S. (2008). “Bridge reliability assessment based on monitoring.” J. Bridge Eng., 258–270.
Guo, T., and Chen, Y. W. (2011). “Field stress/displacement monitoring and fatigue reliability assessment of retrofitted steel bridge details.” Eng. Fail. Anal., 18(1), 354–363.
Guo, T., Li, A. Q., and Wang, H. (2008). “Influence of ambient temperature on the fatigue damage of welded bridge decks.” Int. J. Fatigue, 30(6), 1092–1102.
Hobbacher, A. (2009). IIW recommendations for fatigue design of welded joints and components, Welding Research Council, New York.
Kohout, J., and Veˇchet, S. (2001). “A new function for fatigue curves characterization and its multiple merits.” Int. J. Fatigue, 23(2), 175–183.
Lee, C. K., Chiew, S. P., and Jiang, J. (2012). “Residual stress study of welded high strength steel thin-walled plate-to-plate joints. Part 2: Numerical modeling.” Thin-Walled Struct., 59, 120–131.
Li, A. Q., Ding, Y. L., and Wang, H. (2012). “Analysis and assessment of bridge health monitoring mass data—Progress in research development of ‘Structural Health Monitoring’.” Sci. China Tech. Sci., 55(8), 2212–2224.
Liu, H., Zhou, H., Shi, G., Wang, Y. Q., Shi, Y. J., and De Roeck, G. (2013). “Fatigue assessment of a composite railway bridge for high speed trains. Part II: Conditions for which a dynamic analysis is needed.” J. Constr. Steel Res., 82, 246–254.
Mesmacque, G., Garcia, S., Amrouche, A., and Rubio-Gonzalez, C. (2005). “Sequential law in multiaxial fatigue, a new damage indicator.” Int. J. Fatigue, 27(4), 461–467.
Murakami, Y. (2002). Metal fatigue: Effects of small defects and non-metallic inclusions, Elsevier, Oxford, U.K.
Nishijima, S. (1993). “Basic fatigue properties of JIS steels for machine structural use.” NRIM Special Rep., SR 93-02, NRIM, Tokyo.
Peil, U. (2005). “Assessment of bridges via monitoring.” Struct. Infrastruct. Eng., 1(2), 101–117.
Períc, M., et al. (2014). “Numerical analysis and experimental investigation of welding residual stresses and distortions in a T-joint fillet weld.” J. Constr. Steel Res., 53, 1052–1063.
Pilkey, W. D. (2008). Stress concentration factors, John Wiley & Sons, New York.
Radaj, D. (1996). “Review of fatigue strength assessment of nonwelded and welded structures based on local parameters.” Int. J. Fatigue, 153–170.
Savaidis, G., and Vormwald, M. (2000). “Hot-spot stress evaluation of fatigue in welded structural connections supported by finite element analysis.” Int. J. Fatigue, 18(3), 153–170.
Song, Y. S., and Ding, Y. L. (2013). “Fatigue monitoring and analysis of orthotropic steel deck considering traffic volume and ambient temperature.” Sci. China Tech. Sci., 56(7), 1758–1766.
Wang, Y., Li, Z. X., and Li, A. Q. (2010). “Combined use of SHMS and finite element strain data for assessing the fatigue reliability index of girder components in long-span cable-stayed bridge.” Theor. Appl. Fract. Mech., 54(2), 127–136.
Ye, X. W., Ni, Y. Q., Wong, K. Y., and Ko, J. M. (2012). “Statistical analysis of stress spectra for fatigue life assessment of steel bridges with structural health monitoring data.” Eng. Struct., 45, 166–176.
Zhao, Q., and Wu, C. (2010). “Numerical analysis of welding residual stress of u-rib stiffened plate.” Eng. Mech., 29(8), 262–268 (in Chinese).
Zhou, H., Liu, K., Shi, G., Wang, Y. Q., Shi, Y. J., and De Roeck, G. (2012). “Fatigue assessment of a composite railway bridge for high speed trains. Part I: Modeling and fatigue critical details.” J. Constr. Steel Res., 82, 234–245.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Nov 23, 2015
Accepted: May 27, 2016
Published online: Aug 8, 2016
Published in print: Dec 1, 2016
Discussion open until: Jan 8, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.