Development of Load Rating Procedure for Railroad Flatcar Bridges through Use of Field Instrumentation. I: Data Collection and Analysis
Publication: Journal of Bridge Engineering
Volume 19, Issue 5
Abstract
Because of budget constraints, many state and county highway agencies are often forced to develop innovative and economical replacement strategies for deteriorated bridges. One such option is to use a retired railroad flatcar (RRFC) for a bridge superstructure. Many states have found RRFCs to be successful and economical alternatives to more traditional structural systems. Although the performance of RRFCs has been satisfactory, there is little to no guidance in the AASHTO specifications for load rating these structures. Such inexperience has led some to take overly conservative approaches when rating these bridges. This paper, the first of two companion papers, presents the use of field instrumentation and controlled load testing on seven RRFC bridges located in Indiana. Stress data were used to gain an understanding of the in situ response of these structures, including global bending, secondary bending, and lateral load distribution. Proposed load rating guidelines presented in the second companion paper were developed using data from these load tests as well as other data found in the literature.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was sponsored by the Indiana Local Technical Assistance Program (LTAP). The authors appreciate the support of the Indiana county offices, specifically Clay, Fountain, and Vermillion counties for providing assistance and valuable knowledge with respect to railroad flatcar bridges. The authors also acknowledge the input from Dr. Robert Sweeney of Modjeski and Masters and Mr. John Unsworth of the Canadian Pacific Railroad, who shared their bridge engineering experience. The authors also thank Clark Dietz Engineers for sharing their experience regarding the load rating of railroad flatcar bridges in Indiana. Assistance from various students and staff of Bowen Laboratory at Purdue University is also much appreciated.
References
AASHTO. (2010). LRFD bridge design specifications, 5th Ed., Washington, DC.
Association of American Railroads. (2007). “Design, fabrication, and construction of freight cars.” Manual of standards and recommended practices, Section C, Part II, Washington, DC.
Bridge Diagnostics. (1995). “Technique enables flatcar bridges to attain higher load ratings.” Roads & Bridges, 33(8), 42–43.
Connor, R. J., and Fisher, J. W. (2001). “Results of field measurements on the Williamsburg Bridge orthotropic deck: Final report on phase III.” ATLSS Report 01-01, Center for Advanced Technology for Large Structural Systems, Lehigh Univ., Bethlehem, PA.
Connor, R. J., and Fisher, J. W. (2004). “Results of field measurements made on the prototype orthotropic deck on the Bronx Whitestone Bridge: Final report.” ATLSS Rep. 04–03, Center for Advanced Technology for Large Structural Systems, Lehigh Univ., Bethlehem, PA.
Dexter, R. J., Connor, R. J., and Kaczinski, M. R. (1998). “Fatigue design of modular bridge expansion joints.” NCHRP Rep. 402, National Cooperative Highway Research Program, Washington, DC.
Federal Highway Administration (FHWA). (2008). “2008 NBI ASCII files.” Bridges and structures national bridge inventory, Washington, DC.
Parsons, Thomas J. (1991). “Bridges constructed from railroad cars.” Final Rep. TRC-8901, Arkansas State Highway and Transportation Department and Arkansas State Univ., Little Rock, AR.
Provines, J. T., Connor, R. J., and Sherman, R. J. (2011). “Development of guidelines for the rating, inspection, and acquisition of railroad flatcars for use as highway bridges on low-volume roads.” Indiana Local Technical Assistance Program. Purdue Univ., West Lafayette, IN.
Provines, J. T., Connor, R. J., and Sherman, R. J. (2014). “Development of load rating procedure for railroad flatcar bridges through the use of field instrumentation. II: Procedure development.” J. Bridge Eng., 0413026.
Sherman, R. J., Mueller, J. M., Connor, R. J., and Bowman, M. D. (2011). “Evaluation of effects of super-heavy loading on the US-41 bridge over the White River.” Rep. FHWA/IN/JTRP-2011/15, Joint Transportation Research Program, Indiana DOT and Purdue Univ., West Lafayette, IN.
Wipf, T. J., Klaiber, W. F., Boomsma, H. A., and Palmer, K. S. (2007a). “Field testing of railroad flatcar bridges. I: Single spans.” Final Rep.: Iowa DOT Project TR-498, Iowa State Univ. of Science and Technology, Ames, IA.
Wipf, T. J., Klaiber, W. F., and Doornink, J. D. (2003). “Demonstration project using railroad flatcars for low-volume road bridges.” Final Rep.: Iowa DOT Project TR-444, Iowa State Univ. of Science and Technology, Ames, IA.
Wipf, T. J., Klaiber, W. F., Massa, J. J., Keierleber, B., and Witt, J. (2007b). “Field testing of railroad flatcar bridges. II: Multiple spans.” Final Rep.: Iowa DOT Project TR-498, Iowa State Univ. of Science and Technology, Ames, IA.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 30, 2013
Accepted: Sep 10, 2013
Published online: Sep 12, 2013
Published in print: May 1, 2014
Discussion open until: May 26, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.