Combustion Characteristics of the Solid-Fuel Ramjet with Star Solid Fuel
Publication: Journal of Aerospace Engineering
Volume 31, Issue 4
Abstract
Flow field characteristics of and regression rate distribution for the solid-fuel ramjet (SFRJ) with star solid fuel were investigated by numerical and experimental methods. The experimental data were obtained by burning polyethylene using a connected-pipe facility. The three-dimensional code developed in the present study adopted third-order monotonic upwind scheme for conservation laws (MUSCL) and central difference schemes, advection upstream splitting method by pressure-based weight functions (AUSMPW+), flux vector splitting method, and second-order moment turbulence-chemistry model, together with the shear stress transport (SST) turbulence model. The solid-fuel surface temperature was calculated with the fluid-solid heat coupling method. The numerical results show that obvious circumferential flow exists in the SFRJ with star solid fuel. The regression rates are higher at the star tip and lower at the star bottom. The space-averaged regression rate of star solid fuel is slightly higher than that of the traditional single-port cylindrical solid fuel. Turbulent viscosity is a critical parameter affecting the regression rate distribution, and the circumferential flow in the SFRJ has an important influence on turbulent viscosity. Comparing the numerical and experimental regression rates, it is indicated that the developed code can generally predict the effect of fuel configuration on the regression rate, and further investigation is needed to improve the accuracy and reliability of the developed code. A sudden increase in pressure during the combustion of star solid fuel was observed experimentally, which requires further investigations.
Get full access to this article
View all available purchase options and get full access to this article.
References
Baurle, R. A., Mathur, T., Gruber, M. R., and Jackson, K. R. (1988). “A numerical and experimental investigation of a scramjet combustor for hypersonic missile applications.” Proc., AIAA Joint Propulsion Conf., AIAA, Reston, VA, 1998–3121.
Bianchi, D., Nasuti, F., and Onofri, M. (2015). “Radius of curvature effects on throat thermochemical erosion in solid rocket motors.” J. Spacecraft Rockets, 52(2), 320–330.
Blazek, J. (2006). Computational fluid dynamics: Principles and applications, Elsevier, Oxford, U.K.
Brindle, A., Boyce, R. R., and Neely, A. J. (2005). “CFD analysis of an ethylene-fueled intake-injection shock-induced-combustion scramjet configuration.” Proc., AIAA/CIRA 13th Int. Space Planes and Hypersonics Systems and Technologies, AIAA, Reston, VA, 2005–3239.
Cai, G., Zeng, P., Li, X., Tian, H., and Yu, N. (2013). “Scale effect of fuel regression rate in hybrid rocket motor.” Aerosp. Sci. Technol., 24(1), 141–146.
Carmicino, C., Scaramuzzino, F., and Sorge, A. R. (2014). “Trade-off between paraffin-based and aluminium-loaded HTPB fuels to improve performance of hybrid rocket fed with .” Aerosp. Sci. Technol., 37, 81–92.
Carmicino, C., and Sorge, A. R. (2015). “Experimental investigation into the effect of solid-fuel additives on hybrid rocket performance.” J. Propul. Power, 31(2), 699–713.
Chiaverini, M. J., et al. (1999). “Pyrolysis behavior of hybrid-rocket solid fuels under rapid heating conditions.” J. Propul. Power, 15(6), 888–895.
Chiaverini, M. J., Kuo, K. K., Peretz, A., and Harting, G. C. (2001). “Regression-rate and heat-transfer correlations for hybrid rocket combustion.” J. Propul. Power, 17(1), 99–110.
Evans, B., Favorito, N. A., and Kuo, K. K. (2005). “Study of solid fuel burning-rate enhancement behavior in an X-ray translucent hybrid rocket motor.” Proc., AIAA Joint Propulsion Conf., AIAA, Reston, VA, 2005–3909.
Favaro, F. M., Sirignano, W. A., Manzoni, M., and DeLuca, L. T. (2013). “Solid-fuel regression rate modeling for hybrid rockets.” J. Propul. Power, 29(1), 205–215.
Gascoin, N., Fau, G., and Gillard, P. (2013). “Flash pyrolysis of high density polyethylene.” Proc., AIAA Joint Propulsion Conf., AIAA, Reston, VA, 2013–3833.
Hedman, T. D. (2016). “Radiation-induced pyrolysis of solid fuels for ramjet application.” Propul. Power Res., 5(2), 87–96.
Karabeyoglu, M. A., Altman, D., and Cantwell, B. J. (2002). “Combustion of liquefying hybrid propellants—Part I: General theory.” J. Propul. Power, 18(3), 610–620.
Kim, K. H., Chongam, K., and Rho, O. H. (2001). “Methods for the accurate computations of hypersonic flows—Part I: AUSMPW+ scheme.” J. Comput. Phys., 174(1), 38–80.
Kim, S., and Kwon, O. C. (2013). “Regression characteristics of the cylindrical multiport grain in hybrid rockets.” J. Propul. Power, 29(3), 573–581.
Kim, S., Moon, H., and Kim, J. (2015). “Thermal characterizations of the paraffin wax low density polyethylene blends as a solid fuel.” Thermochim. Acta, 613, 9–16.
Krishnan, S., and George, P. (1998). “Solid fuel ramjet combustor design.” Prog. Aerosp. Sci., 34(3), 219–256.
Kumar, C. P., and Kumar, A. (2013). “Effect of diaphragm on regression rate in hybrid rocket motors.” J. Propul. Power, 29(3), 559–572.
Kuo, K. K., and Chiaverini, M. J. (2007). Fundamentals of hybrid rocket combustion and propulsion, AIAA, Reston, VA.
Lee, C., Na, Y., Lee, J. W., and Byun, Y. H. (2007). “Effect of induced swirl flow on regression rate of hybrid rocket fuel by helical grain configuration.” Aerosp. Sci. Technol., 11(1), 68–76.
Lee, J., Kim, S., Kim, J., and Moon, H. (2015). “Mass transfer number sensitivity on the fuel burning rate in hybrid rockets.” J. Propul. Power, 31(4), 1041–1050.
Li, X., Tian, H., and Cai, G. (2013). “Numerical analysis of fuel regression rate distribution characteristics in hybrid rocket motors with different fuel types.” Sci. China Technol. Sci., 56(7), 1807–1817.
Marxman, G. A. (1967). “Boundary-layer combustion in propulsion.” Proc., Symp. (Int.) on Combustion, Vol. 11, Combustion Institute, Pittsburgh, PA, 269–289.
Mazzetti, A., and Barbante, P. (2016). “Numerical modeling of combustion processes in hybrid rocket engines.” Int. J. Energy Mater. Chem. Propul., 15(3), 249–274.
Menter, F. R. (1994). “Two equation eddy viscosity turbulence models for engineering application.” AIAA J., 32(8), 1598–1605.
Merotto, L., and Mazzetti, A. (2013). “Numerical simulations of combustion processes in hybrid rocket engines using OpenFoam and COOLFluiD codes.” Proc., 5th European Conf. for Aeronautics and Space Sciences, EUCASS Association, Munich, Germany.
Musa, O., Chen, X., and Zhou, C. (2017). “Combustion characteristics and turbulence modeling of swirling reacting flow in solid fuel ramjet.” Acta Astronaut., 139, 1–17.
Musa, O., Chen, X., and Zhou, C. S. (2017). “Effect of inlet conditions on swirling turbulent reacting flows in a solid fuel ramjet engine.” Appl. Therm. Eng., 113, 186–207.
Netzer, A., and Gany, A. (1991). “Burning and flameholding characteristics of a miniature solid fuel ramjet combustor.” Propellants Explos. Pyrotech., 7(3), 357–363.
Schulte, G., Pein, R., and Högl, A. (1987). “Temperature and concentration measurements in a solid fuel ramjet combustion chamber.” J. Propul. Power, 3(2), 114–120.
Senneca, O., Chirone, R., and Salatino, P. (2004). “Oxidative pyrolysis of solid fuels.” J. Anal. Appl. Pyrolysis, 71(2), 959–970.
Stoliarov, S. I., and Walters, R. N. (2008). “Determination of the heats of gasification of polymers using differential scanning calorimetry.” Polym. Degrad. Stab., 93(2), 422–427.
Sun, X., Tian, H., Li, Y., Yu, N., and Cai, G. (2016). “Regression rate behaviors of HTPB-based propellant combinations for hybrid rocket motor.” Acta Astronaut., 119, 137–146.
Sun, X., Tian, H., Yu, N., and Cai, G. (2015), “Regression rate and combustion performance investigation of aluminum metallized HTPB/98HP hybrid rocket motor with numerical simulation.” Aerosp. Sci. Technol., 42, 287–296.
Tian, H., Li, X., Zeng, P., Yu, N., and Cai, G. (2014). “Numerical and experimental studies of the hybrid rocket motor with multi-port fuel grain.” Acta Astronaut., 96, 261–268.
Tian, H., Sun, X., Guo, Y., and Wang, P. (2015). “Combustion characteristics of hybrid rocket motor with segmented grain.” Acta Astronaut., 46, 537–547.
Whitmore, S. A., and Walker, S. D. (2017). “Engineering model for hybrid fuel regression rate amplification using helical ports.” J. Propul. Power, 33(2), 398–407.
Zhang, L. P., and Wang, Z. J. (2004). “A block LU-SGS implicit dual time-stepping algorithm for hybrid dynamic meshes.” Comput. Fluids, 33(7), 891–916.
Zhang, S., Hu, F., and Zhang, W. (2016). “Numerical investigation on the regression rate of hybrid rocket motor with star swirl fuel grain.” Acta Astronaut., 127, 384–393.
Zhou, L. X., Wang, F., and Zhang, J. (2003a). “Simulation of swirling combustion and NO formation using a USM turbulence-chemistry model.” Fuel, 82(13), 1579–1586.
Zhou, L. X., Zhang, Y., and Zhang, J. (2003b). “Simulation of swirling coal combustion using a full two-fluid model and an AUSM turbulence-chemistry model.” Fuel, 82(8), 1001–1007.
Zilliac, G., and Karabeyoglu, M. A. (2006). “Hybrid rocket fuel regression rate data and modeling.” Proc., AIAA Joint Propulsion Conf., AIAA, Reston, VA, 2006–4504.
Zvuloni, R., Gany, A., and Levy, Y. (1989). “Geometric effects on the combustion in solid fuel ramjets.” J. Propul. Power, 5(1), 32–37.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jul 14, 2017
Accepted: Oct 16, 2017
Published online: Apr 6, 2018
Published in print: Jul 1, 2018
Discussion open until: Sep 6, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.