Optimization and Performance Analysis of Oleo-Honeycomb Damper Used in Vertical Landing Reusable Launch Vehicle
Publication: Journal of Aerospace Engineering
Volume 31, Issue 2
Abstract
A dynamic model is proposed and validated to analyze the landing performance of a vertical landing reusable launch vehicle (RLV) with a novel oleo-honeycomb two-stage damper. Based on this model and design requirements, seven critical landing conditions are found as a foundation of the following multiobjective and multiconstraint optimization for oleo-honeycomb damper. In order to overcome the time-consuming and variable coupling problem of the optimization, a combinatorial optimization method is proposed and verified with collaborative optimization (CO) combined with an archive-based micro-genetic algorithm (AMGA). Meanwhile, relaxation factors and the radial basis function (RBF) model are employed to improve the computational accuracy and efficiency. After obtaining the optimal solution, the influences of the landing strut friction coefficient and ground friction coefficient on the soft-landing process are analyzed. The results show that the combinatorial optimization method is feasible and efficient, and the selection of honeycomb crushing force and hydraulic damper’s parameters affect and restrict each other. The oleo-honeycomb damper has some advantages over traditional dampers and two factors of initial landing conditions have different influences on touchdown stability, impact acceleration, and nozzle ground clearance.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the Fundamental Research Funds for the Central Universities (Grant No. NS2016001), Joint Funds of the Aerospace Technology (Grant No. 6141B06010201), and the Priority Academic Program Development of Jiangsu Higher Education Institutions.
References
ADAMS [Computer software]. MSC Software, Newport Beach, CA.
Bhatt, J. R., Mishra, H., and Sreekanth, V. (2011). “Shear viscosity, cavitation and hydrodynamics at LHC.” Phys. Lett. B, 704(5), 486–489.
Chen, J. B., and Nie, H. (2008). “Over loading of landing based on the deformation of the lunar lander.” Chin. J. Aeronaut., 21(1), 43–47.
Chen, J. B., Nie, H., Wan, J. L., and Lin, Q. (2014). “Investigation on landing impact dynamic and low-gravity experiments for deep space lander.” Sci. China Phys. Mech. Astron., 57(10), 1987–1997.
Dumbacher, D. L. (2001). “NASA 2nd generation RLV program introduction, status and future plans.”, American Institute of Aeronautics and Astronautics, Reston, VA.
Fang, H., and Wang, Q. (2008). “On the effectiveness of assessing model accuracy at design points for radial basis functions.” Commun. Numer. Methods Eng., 24(3), 219–235.
Gutmann, H. M. (2000). “A radial basis function method for global optimization.” J. Global Optim., 19(3), 201–227.
HexWeb. (2005). “Honeycomb energy absorption systems design data.” Stamford, CT.
Hulme, K. F., and Bloebaum, C. L. (2000). “A simulation-based comparison of multidisciplinary design optimization solution strategies using cascade.” Struct. Multidiscip. Optim., 19(1), 17–35.
Jin, R., Chen, W., and Sudjianto, A. (2005). “An efficient algorithm for constructing optimal design of computer experiments.” J. Stat. Plann. Inference, 134(1), 268–287.
Laurenson, R. M., Melliere, R. A., and Mcgehee, J. R. (1973). “Analysis of legged landers for the survivable soft landing of instrument payloads.” J. Spacecraft Rockets, 10(3), 208–214.
Li, X., Li, W., and Liu, C. (2008). “Geometric analysis of collaborative optimization.” Struct. Multidiscip. Optim., 35(4), 301–313.
Li, X., Liu, C. A., Li, W. J., and Long, T. (2011). “An alternative formulation of collaborative optimization based on geometric analysis.” J. Mech. Des., 133(5), 051005.
Lin, Q., Kang, Z., Ren, J., Zhao, Q., and Nie, H. (2014). “Impact analysis of lunar lander soft landing performance caused by the body gravity centerline shift.” J. Aerosp. Eng., 2157–2166.
Padula, S. L., Alexandrov, N., and Green, L. L. (1996). “MDO test suite at NASA Langley Research Center.” 6th AI-AA/NASA/ISSMO Symp. on Multidisciplinary Analysis and Optimization, AIAA-1996-4028, American Institute of Aeronautics and Astronautics, Reston, VA.
Pham, V. L., Zhao, J., Goo, N. S., Lim, J. H., Hwang, D.-S., and Park, J. S. (2013). “Landing stability simulation of a 1/6 lunar module with aluminum honeycomb dampers.” Int. J. Aeronaut. Space, 14(4), 356–368.
Santosa, S. P., Wierzbicki, T., Hanssen, A. G., and Langseth, M. (2000). “Experiment and numerical studies of foam-filled sections.” Int. J. Impact Eng., 24(5), 509–534.
Sargent, L. B. (1983). “Pressure-viscosity coefficients of liquid lubricants.” Tribol. Trans., 26(1), 1–10.
Song, G. S., and Wang, C. J. (2013). “Landing stability of the lunar lander based on Monte Carlo approach.” J. Beijing Univ. Aeronaut. Astronaut., 39(9), 1192–1196 (in Chinese).
Sperling, F. B. (1964). “The surveyor shock absorber.” Proc., 3rd Aerospace Mechanisms Symp., N50–17368, National Aeronautics and Space Administration, Hampton, VA.
Stockfleth, H., Roth, M., and Kleinau, W. (1996). “Landing gear system for VTVL launcher.” 47th Int. Astronautic Congress, International Astronautical Federation, Paris, 14–29.
Sun, Y., Hu, Y., Liu, R., and Deng, Z. (2010). “Touchdown dynamic modeling and simulation of lunar lander.” Int. Symp. on Systems and Control in Aeronautics and Astronautics, IEEE, New York, 1320–1324.
Tiwari, S., Koch, P., Fadel, G., and Deb, K. (2008). “AMGA: An archive-based micro genetic algorithm for multi-objective optimization.” Proc., 10th Annual Conf. on Genetic and Evolutionary Computation, Association for Computing Machinery, New York, 729–736.
Wan, J. L., Nie, H., Chen, J. B., Li, L. C., and Wang, A. L. (2010). “Impact response analysis of payloads of lunar lander for lunar landing.” J. Astronaut., 11, 5 (in Chinese).
Wang, J. J., Wang, C. J., and Song, G. S. (2014). “Performance optimization of lunar lander based on response surface methodology.” J. Beijing Univ. Aeronaut. Astronaut., 40(5), 707–711 (in Chinese).
Wei, X., Lin, Q., Nie, H., Zhang, M., and Ren, J. (2014). “Investigation on soft-landing dynamics of four-legged lunar lander.” Acta Astronaut., 101(1), 55–66.
Wei, X., and Nie, H. (2005). “Dynamic analysis of aircraft landing impact using landing-region-based model.” J. Aircraft, 42(6), 1631–1637.
Wierzbicki, T. (1983). “Crushing analysis of metal honeycombs.” Int. J. Impact Eng., 1(2), 157–174.
Wittenburg, J. (1977). Dynamics of systems of rigid bodies, B. G. Teubner, Stuttgart, Germany.
Wong, J. Y. (2001). Theory of ground vehicles, 3rd Ed., Wiley, New York.
Yang, J., Zeng, F., Man, J., and Zhu, W. (2014). “Design and verification of the landing impact attenuation system for Chang’E-3 lander.” Sci. Sin. Technol., 44(5), 440–449 (in Chinese).
Yin, H., Wen, G., Hou, S., and Chen, K. (2011). “Crushing analysis and multiobjective crashworthiness optimization of honeycomb-filled single and bitubular polygonal tubes.” Mater. Des., 32(8–9), 4449–4460.
Zou, Z., Reid, S. R., Tan, P. J., Li, S., and Harrigan, J. J. (2009). “Dynamic crushing of honeycombs and features of shock fronts.” Int. J. Impact Eng., 36(1), 165–176.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jun 15, 2017
Accepted: Sep 13, 2017
Published online: Jan 6, 2018
Published in print: Mar 1, 2018
Discussion open until: Jun 6, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.