Influence of Mineral Composition on Sintering Lunar Regolith
Publication: Journal of Aerospace Engineering
Volume 30, Issue 4
Abstract
The authors investigate mechanical properties of sintered lunar regolith. Using JSC-1A and DNA lunar simulants, they study the influence of changes in glass content, main plagioclase series, and ilmenite content on a defined sintering process and on the mechanical properties of resulting sintered samples. Ilmenite addition up to 20 wt% of the regolith showed a negligible effect on the sintered product. The anorthite plagioclase endmember cannot be replaced by albite, responsible for the low sintering temperature of DNA and covering up the effect of the glass phase. The vacuum environment was revealed to have a positive effect on JSC-1A sintering: the grains bond at lower temperature than in air, thus preventing the formation of additional porosity and increasing the compression strength up to 152 MPa compared with only 98 MPa for sintering JSC-1A in air.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work has been carried out within the project entitled “3D printing of a model building block for a lunar base outershell” funded by ESA’s General Support Technology Programm (GSTP). The authors wish to thank Advenit Makaya and Laurent Pambaguian, from ESA-ESTEC, for the interesting discussions and constructive comments during the project.
References
Badescu, V., Schwandt, C., Hamilton, J. A., Fray, D. J., and Crawford, I. A. (2012). Moon: Prospective energy and material resources. Springer Science and Business Media, Berlin.
Benaroya, H., and Bernold, L. (2008). “Engineering of lunar bases.” Acta Astronaut., 62(4), 277–299.
Carrier, W. D. III, Olhoeft, G. R., and Mendell, W. (1991). “Physical properties of the lunar surface.” Lunar sourcebook, Cambridge University Press, Cambridge, U.K., 475–594.
Carter, C. B., and Norton, M. G. (2007). Ceramic materials: Science and engineering, Springer Science and Business Media, New York.
Cesaretti, G., Dini, E., De Kestelier, X., Colla, V., and Pambaguian, L. (2014). “Building components for an outpost on the lunar soil by means of a novel 3D printing technology.” Acta Astronaut., 93, 430–450.
Deer, W. A., et al. (1992). An introduction to the rock-forming minerals, Longman, London.
Fabri, D., Guan, J., and Cesàro, A. (1998). “Crystallisation and melting behaviour of poly (3-hydroxybutyrate) in dilute solution: Towards an understanding of physical gels.” Thermochim. acta, 321(1), 3–16.
Fateri, M., and Gebhardt, A. (2015). “Process parameters development of selective laser melting of lunar regolith for on-site manufacturing applications.” Int. J. Appl. Ceram. Technol., 12(1), 46–52.
Gualtieri, T., and Bandyopadhyay, A. (2015). “Compressive deformation of porous lunar regolith.” Mater. Lett., 143, 276–278.
Heiken, G., Vaniman, D., and French, B. M. (1991). Lunar source book: A user’s guide to the moon, Cambridge University Press, Cambridge, U.K.
Hill, E., Mellin, M. J., Deane, B., Liu, Y., and Taylor, L. A. (2007). “Apollo sample 70051 and high-and low-Ti lunar soil simulants MLS-1A and JSC-1A: Implications for future lunar exploration.” J. Geophys. Res.: Planets, 112(E2), 1–11.
Hintze, P. E., Curran, J., and Back, T. (2009). “Lunar surface stabilization via sintering or the use of heat cured polymers.” 47th AIAA Aerospace Science Meeting, AIAA, Reston, VA, 1009–1015.
Kingery, W., Uhlmann, D. R., and Bowen, H. K. (1976). Introduction to ceramics, Wiley, New York.
Krishna Balla, V., Roberson, L. B., O’Connor, G. W., Trigwell, S., Bose, S., and Bandyopadhyay, A. (2012). “First demonstration on direct laser fabrication of lunar regolith parts.” Rapid Prototyping J., 18(6), 451–457.
Lynch, G. (1994). “Bricks: Properties and classifications.” Struct. Surv., 12(4), 15–20.
Pletka, B. J. (1993). “Processing of lunar basalt materials.” Resources of near Earth space, University of Arizona Press, Tucson, AZ, 325–350.
Rahaman, M. N. (2003). Ceramic processing and sintering, 2nd Ed., CRC Press, New York.
Ray, C. S., Reis, S. T., Sen, S., and O’Dell, J. S. (2010). “JSC-1A lunar soil simulant: Characterization, glass formation, and selected glass properties.” J. Non-Cryst. Solids, 356(44), 2369–2374.
Rickman, D., McLemore, C., and Fikes, J. (2007). “Characterization summary of jsc-1a bulk lunar mare regolith simulant.” National Aeronautics and Space Administration, Washington, DC.
Rousek, T., Eriksson, K., and Doule, O. (2012). “Sinterhab.” Acta Astronaut., 74, 98–111.
Ruess, F., Schaenzlin, J., and Benaroya, H. (2006). “Structural design of a lunar habitat.” J. Aerosp. Eng., 133–157.
Schrader, C., et al. (2008). “Extant and extinct lunar regolith simulants: Modal analyses of NU-LHT-1M and -2m, OB-1, JSC-1, JSC-1A and -1AF, FJS-1, and MLS-1.” Planetary Mining and Science Symp., Montreal.
Taylor, L. A., and Liu, Y. (2010). “Important considerations for lunar soil simulants.” Proc., Earth and Space, ASCE, Reston, VA.
Taylor, L. A., and Meek, T. T. (2005). “Microwave sintering of lunar soil: properties, theory, and practice.” J. Aerosp. Eng., 188–196.
Vlasyuk, R. Z., and Radomysel’skii, I. D. (1971). “Crystallization processes in the silicate phase during the sintering of metal-glass materials.” Powder Metall. Met. Ceram., 10(7), 526–531.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Jun 2, 2016
Accepted: Oct 28, 2016
Published online: Feb 10, 2017
Published in print: Jul 1, 2017
Discussion open until: Jul 10, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.