Planar Nozzles for Controllable Microthrusters
Publication: Journal of Aerospace Engineering
Volume 30, Issue 3
Abstract
Orbital maneuvering of microsatellite and nanosatellite requirements can be efficiently addressed by planar nozzles, in which real-time thrust control is gained actuating on the nozzle throat area. In the present work, the method of characteristics is used to design a hypersonic contour; then, the resulting profile is laser cut, assembled, and built into a propulsion system to finally perform tests in a vacuum chamber under several working conditions. Results are used to validate the profile and modeling assumptions and investigate overall behavior. Tests showed that thrust-inlet pressure ratio is a linear function of separation between nozzle contours and that no additional losses are introduced in the system. The corresponding design/manufacture/assembly tools can be used to a provide low-cost/low-weight controllable propulsion systems to the small-satellite industry with no efficiency loss.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank A. Beceyro Ferran, L. De Cunto, and J. Zapata Usandivaras for their collaboration in the experimental work, Satellogic for their generous donation of the test bench, and Instituto Tecnologico de Buenos Aires for the funding granted through ITBACyT.
References
Adler, S., Warshavsky, A., and Peretz, A. (2005). “Low-cost cold-gas reaction control system for sloshsat FLEVO small satellite.” J. Spacecraft Rockets, 42(2), 345–351.
Anderson, J. D. (1995). Computational fluid dynamics: The basics with applications, McGraw-Hill, New York.
Anderson, J. D. (2003). Modern compressible fluid flow with historical perspective, McGraw-Hill, New York.
ANSYS 14.5 [Computer software]. ANSYS, Canonsburg, PA.
Balabel, A., Hegab, A. M., Nasr, M., and El-Behery, S. (2011). “Assessment of turbulence modeling for gas flow in two-dimensional convergent-divergent rocket nozzle.” Appl. Math. Modell., 35(7), 3408–3422.
Bayt, R. L., Ayon, A. A., and Breuer, K. S. (1997). “A performance evaluation of MEMS-based micronozzles.” 33rd Joint Propulsion Conf. and Exhibit, American Institute of Aeronautics and Astronautics, Reston, VA.
Bzibziak, R. (2000). “Update of cold gas propulsion at Moog.” 36th AIAA/ASME/SAE/ASEE Joint Propulsion Conf. and Exhibit, American Institute of Aeronautics and Astronautics, Reston, VA.
CU Aerospace/Vacco. (2014). “Propulsion unit for CubeSats PUC-SO2.”, CU Aerospace, Champaign, IL.
Donaldson, C. (1948). “Note on the importance of imperfect gas effects and variation of heat capacities on the isentropic flow of gases.” NASA, Washington, DC.
Gibbon, D. M. (2004). “Development of a next generation low power small satellite thruster.”, Surrey Satellite Technology, Guildford, U.K.
Grisnik, S. P., Smith, T. A., and Salz, L. E. (1987). “Experimental study of low Reynolds number nozzles.”, American Institute of Aeronautics and Astronautics, Reston, VA.
Janson, S., Helvajian, H., Hansen, W., and Lodmell, J. (1999a). “Microthrusters for nanosatellites.” 2nd Int. Conf. on Integrated Micro Nanotechnology for Space Applications, Aerospace Corporation, El Segundo, CA.
Janson, S. W., Helvajian, H., and Hansen, W. W. (1999b). “Batch fabricated CW microthrusters for kilogram-class spacecraft.” 35th AIIA/ASME/SAE/ASEE Joint Propulsion Conf. and Exhibit, Aerospace Corporation, El Segundo, CA.
Jasak, K., Weller, H. G., and Gosman, A. D. (1999). “High resolution NVD differencing scheme for arbitrarily unstructured meshes.” Int. J. Numer. Methods Fluids, 31(2), 431–449.
Kim, J., Kim, H., and Park, K. (2006). “Computational/experimental study of variable critical nozzle flow.” Flow Meas. Instrum., 17(2), 81–86.
Kliegel, J., and Quan, V. (1966). Convergent-divergent nozzle flow. American Institute of Aeronautics and Astronautics, Reston, VA.
Louisos, W., and Hitt, D. (2007). “Heat transfer and viscous effects in 2D & 3D micro-400 nozzles.” 37th AIAA Fluid Dynamics Conf., American Institute of Aeronautics and Astronautics, Reston, VA.
Majumdar, S. (1988). “Role of underrelaxation in momentum interpolation for calculation of flow with nonstaggered grids.” Numer. Heat Transfer, 13(1), 125–132.
Matticari, G. (2009). “Cold gas microthruster system for Galileo Galilei Spacecraft.”, Thales Alenia Space, Cannes, France.
NASA Ames Research Center Mission Design Division Staff. (2013). “Small spacecraft technology state of the art.”, Moffett Field, Mountain View, CA.
Neckel, A. L., and Godinho, M. (2015). “Influence of geometry on the efficiency of convergent-divergent nozzles applied to Tesla turbines.” Exp. Ther. Fluid Sci., 62, 131–140.
Omnidea-RTG. (2014). “Space propulsion components product catalogue.” Sthur, Germany.
Östlund, J. (2002). “Flow processes in rocket engine nozzles with focus on flow separation and side loads.” M.S. thesis, Royal Institute of Technology, Stockholm, Sweden.
Otobe, Y., Kashimura, H., Matsuo, S., Setoguchi, T., and Kim, H. (2008). “Influence of nozzle geometry on the near-field structure of a highly underxpanded sonic jet.” J. Fluids Struct., 24(2), 281–293.
Pedreira, P. H., Lauretta, J. R., and D’hers, S. (2015). “Controllable planar nozzles for microthrusters.” 1st Pan-American Congress on Computational Mechanics—PANACM 2015, International Center for Numerical Methods in Engineering (CIMNE), Barcelona, Spain.
Raw, M. J. (1996). “Robustness of coupled algebraic multigrid for the Navier-Stokes equations.” 34th Aerospace and Sciences Meeting and Exhibit, American Institute of Aeronautics and Astronautics, Reston, VA.
Rossi, C., Briand, D., Dumonteuil, M., Camps, T., Pham, P., and de Rooij, N. (2006). “Matrix of addressed solid propellant microthrusters: Review of the technologies.” Sens. Actuators, A, 126(1), 241–252.
Sainte-Rose, B., Bertier, N., Deck, S., and Dupoirieux, F. (2012). “Numerical simulations and physical analysis of an over expanded reactive gas flow in a planar nozzle.” Combust. Flame, 159(9), 2856–2871.
Schlichting, H. (1979). Boundary-layer theory, McGraw-Hill, New York.
Shapiro, A. (1953). The dynamics and thermodynamics of compressible fluid flow, Ronald Press, New York.
Shyy, W., and Krishnamurty, V. S. (1997). “Compressibility effects in modeling complex turbulent flows.” Prog. Aerosp. Sci., 33(9–10), 587–645.
Smith, P. (2006). “Resistojet thruster design and development programme.” 42nd AIAA/ASME/SAE/ASEE Joint Propulsion Conf. and Exhibit, American Institute of Aeronautics and Astronautics, Reston, VA.
Usbeck, T., Wohlfart, J., and Schelkle, M. (2004). “A flexible cold gas propulsion system concept for different space applications.” Proc., 4th Int. Spacecraft Propulsion Conf. (ESA SP-555), European Space Agency, Paris.
van Driest, E. R. (1951). “Turbulent boundary layer in compressible fluids.” J. Spacecraft Rockets, 40(6), 1012–1028.
Wilcox, D. C. (1986). “Multiscale model for turbulent flows.” 24th AIAA Aerospace Sciences Meeting, American Institute of Aeronautics and Astronautics, Reston, VA.
Zebbiche, T. (2011). “Stagnation temperature effect on the supersonic axisymmetric minimum length nozzle design with application for air.” Adv. Space Res., 48(10), 1656–1675.
Information & Authors
Information
Published In
Copyright
©2016 American Society of Civil Engineers.
History
Received: Mar 9, 2016
Accepted: Aug 8, 2016
Published online: Dec 2, 2016
Published in print: May 1, 2017
Discussion open until: May 2, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.