Three-Dimensional Numerical Study of the Conical Nozzle Side Loads during Staging
Publication: Journal of Aerospace Engineering
Volume 29, Issue 5
Abstract
The objective of this paper is to numerically investigate the three-dimensional side loads and associated flow physics of a conical nozzle during the fire-in-the-hole staging event of the multistage rocket. The transient flow in nozzle is examined by a three-dimensional time-accurate numerical method with the start-up process of the upper-stage motor and the prescribed nominal separating motion of the lower stage. The impacts of asymmetric lateral motion due to non-nominal staging movement on the nozzle side loads are also numerically analyzed. These motion deviations include the relative angle between axes of two stages, relative lateral displacement between two stages, superposition of relative angle with relative lateral displacement, and angle of thrust vector control. As presented in the simulation results, the flow separation in nozzle is significantly prolonged and intensified by the obstruction of the lower stage. With the location of shockwave reflection approaching the dome of lower stage, the nozzle flow structure experiences two different, stable free shock separation (FSS) patterns. The transition from the first pattern to the second pattern results in the flow oscillation and the side loads peak. The staging motion deviations result in not only the enlarged nozzle side loads, but also a sustained unidirectional effect that may influence the flight stability of the upper stage. An essential ingredient driving the flow unsteadiness and asymmetry is related to the asymmetric reverse supersonic flow deflected by the dome and skirt corner of lower stage. Lastly, the flight data of maximum lateral force during staging of Scout’s stage I and stage II is discussed and compared with the computed results in the article.
Get full access to this article
View all available purchase options and get full access to this article.
References
Alziary De Roquefort, T. (2002). “Low frequency fluctuations in separated turbulent compressible flows.” Symp. on Advanced Fluid, Tokyo.
ANSYS 14.0 [Computer software]. ANSYS, Canonsburg, PA.
Bowyer, J. M., Kreiter, G. W., and Petersen, R. E. (1978). “An investigation of the side force that is sometimes observed in rocket motor start-up.” AIAA Paper 78-104514th Joint Propulsion Conf., AIAA, Reston, VA.
Cikanek, H. A. (1987). “Characteristics of space shuttle main engine failures.” AIAA Paper 87-193923rd Joint Propulsion Conf., AIAA, Reston, VA.
Deck, S. (2009). “Delayed detached eddy simulation of the end-effect regime and side-loads in an overexpanded nozzle flow.” Shock Waves, 19(3), 239–249.
Deck, S., and Guillen, P. (2002). “Numerical simulation of side loads in an ideal truncated nozzle.” J. Propul. Power, 18(2), 261–269.
Deck, S., and Nguyen, A. T. (2004). “Unsteady side loads in a thrust-optimized contour nozzle at hysteresis regime.” AIAA J., 42(9), 1878–1888.
Frey, M., and Hagemann, G. (1999). “Flow separation and side-loads in rocket nozzles.” AIAA Paper 99-2815, 35th Joint Propulsion Conf., AIAA, Reston, VA.
Gross, A., and Weiland, C. (2004). “Numerical simulation of separated cold gas nozzle flows.” J. Propul. Power, 20(3), 509–519.
Hunter, C. A. (2004). “Experimental investigation of separated nozzle glows.” J. Propul. Power, 20(3), 527–532.
Huseman, P. G. (1995). “CFD analysis of Titan IV fire-in-the-hole staging.” 33rd Aerospace Sciences Meeting & Exhibit, AIAA, Reston, VA.
Jia, R., Jiang, Z., and Zhang, W. (2015). “Numerical simulation of initial phase of multi-stage rocket stage separation at low altitude.” Chin. J. Astronautics, 36(11), 1310–1317.
Jia, R., Jiang, Z., and Zhang, W. (2016). “Numerical analysis of flow separation and side loads of a conical nozzle during staging.” Proc., IMechE. Part G: J. Aerosp. Eng., 230(5), 845–855.
Li, Y., Eggers, T., and Reimann, B. (2012). “A dynamics study for the hot stage separation of a multistage rocket with a coupled CFD flight mechanics approach.” AIAA Paper 2012-5820, 18th AIAA/3AF International Space Planes & Hypersonic Systems & Technologies Conf., AIAA, Reston, VA.
Luke, G. D., and Adams, D. E. (1992). “Use of nozzle trip rings to reduce nozzle separation side force during staging.” AIAA Paper 92-3617, 28th Joint Propulsion Conf. & Exhibit, AIAA, Reston, VA.
Menter, F. R. (1994). “Two-equation eddy-viscosity turbulence models for engineering applications.” AIAA J., 32(8), 1598–1605.
Moríñigo, J. A., and Salvá, J. J. (2006). “Three-dimensional simulation of the self-oscillating flow and side-loads in an over-expanded subscale rocket nozzle.” Proc., IMechE. Part G: J. Aerosp. Eng., 220(5), 507–523.
Moríñigo, J. A., and Salvá, J. J. (2008). “Numerical study of the start-up process in an optimized rocket nozzle.” Aerosp. Sci. Technol., 12(6), 485–489.
Nave, L. H., and Coffey, G. A. (1973). “Sea level side loads in high-area-ratio rocket engines.” AIAA Paper 73-1284, 9th Propulsion Conf., AIAA, Reston, VA.
Ostlund, J., and Muhammad-Klingmann, B. (2005). “Supersonic flow separation with application to rocket engine nozzles.” Appl. Mech. Rev., 58(3), 143–177.
Pamadi, B. N., Pei, J., and Pinier, J. T. (2012). “Aerodynamic analyses and database development for Ares I vehicle first-stage separation.” J. Spacecraft Rockets, 49(5), 864–874.
Sadunas, J. A., French, E. P., and Daines, W. L. (1980). “Prediction of nozzle side forces which occur during staging.” J. Spacecraft Rockets, 18(5), 406–410.
Shams, A., Lehnasch, G., and Comte, P. (2013). “Unsteadiness in shock-induced separated flow with subsequent reattachment of supersonic annular jet.” Comput. Fluids, 78, 63–74.
Shimizu, T., Miyajima, H., and Kodera, M. (2006). “Numerical study of restricted shock separation in a compressed truncated perfect nozzle.” AIAA J., 44(3), 576–584.
Wang, J. C. T. (1997). “Coupled CFD and rigid body dynamics analysis for the launch vehicles stage separation.” AIAA Paper 97-2944, 33rd Joint Propulsion Conf. & Exhibit, AIAA, Reston, VA.
Wang, T. (2004). “Transient three-dimensional analysis of side load in liquid rocket engine nozzles.” AIAA Paper 2004-3691, 40th Joint Propulsion Conf. & Exhibit, AIAA, Reston, VA.
Wang, T. (2009). “Transient three-dimensional startup side load analysis of a regenerative cooled nozzle.” Shock Waves, 19(3), 251–264.
Wang, T., Lin, J., and Guidos, M. (2013). “Transient side-load analysis of out-of-round film-cooled nozzle extensions.” J. Propul. Power, 29(4), 855–866.
Wang, T., Lin, J., Ruf, J., and Guidos, M. (2011). “Transient three-dimensional side-load analysis of out-of-round film-cooled nozzles.” J. Propul. Power, 27(4), 899–907.
Wasko, R. A. (1961). “Experimental investigation of stage separation aerodynamics.”, National Aeronautics and Space Administration, Washington, DC.
Watanabe, Y., Sakazume, N., and Tsuboi, M. (2002). “LE-7A engine nozzle problems during the transient operations.” AIAA Paper 2002-3841, 38th Joint Propulsion Conf. & Exhibit, AIAA, Reston, VA.
Winterfeldt, L., et al. (2005). “Redesign of the Vulcain 2 nozzle extension.” AIAA Paper 2005-4536, 41st AIAA/ASME/SAE/ASEE Joint Propulsion Conf. & Exhibit, AIAA, Reston, VA.
Yonezawa, K., Yokota, K., Tsujimoto, Y., Sakazume, N., and Watanabe, Y. (2002). “Three-dimensional unsteady flow simulation of compressed truncated perfect nozzles.” AIAA Paper 2002-3991, 38th AIAA/ASME/SAE/ASEE Joint Propulsion Conf. & Exhibit, AIAA, Reston, VA.
Information & Authors
Information
Published In
Journal of Aerospace Engineering
Volume 29 • Issue 5 • September 2016
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Sep 12, 2015
Accepted: Feb 24, 2016
Published online: May 19, 2016
Published in print: Sep 1, 2016
Discussion open until: Oct 19, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.