Flexural Performance of Concrete Beams Reinforced with FRP Grids
Publication: Journal of Composites for Construction
Volume 5, Issue 1
Abstract
This paper evaluates the flexural performance of simply supported concrete beams subjected to four-point monotonic loading and reinforced with a 2D fiber-reinforced plastic (FRP) grid. The main parameter of the study is the amount of longitudinal FRP reinforcement. With respect to a balanced strain condition, three underreinforced and two overreinforced FRP designs were tested with three identical beams per design. Laboratory recorded load-deflection, failure mode, cracking behavior, and reinforcement strain data are compared with theoretical predictions calculated according to traditional steel-reinforced concrete procedures. The study concludes that, with respect to ACI 318-95, flexural capacity is accurately predicted, but shear strength is not. Deflection compatibility between test results and ACI predictions employing the Branson effective moment of inertia was dependent on the percentage of longitudinal reinforcement. In general, observed flexural stiffness was less than that predicted by Branson's equation. A moment-curvature deflection procedure employing a bilinear concrete model compared very well with measured deflections. Finally, the grid configuration provides an effective force transfer mechanism. Cracking occurred at transverse bar locations only, and FRP tensile rupture was achieved with no observed deterioration in force transfer mechanics.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Concrete Institute (ACI). ( 1995). “Building code requirements for structural concrete and commentary.” ACI 318-95 and ACI-318R-95, Farmington Hills, Mich.
2.
ASTM. ( 1984). “Standard test method for compressive strength of cylinder concrete specimens.” C39-84, West Conshohocken, Pa.
3.
Bank, C. L., Yehoshua, F., and Shapira, A. ( 1997). “Three-dimensional fiber-reinforced plastic grating cages for concrete beams: A pilot study.” ACI Struct. J., 94(6), 643–652.
4.
Banthia, N., Al-Asaly, M., and Ma, S. (1995). “Behavior of concrete slabs reinforced with fiber-reinforced plastic grid.”J. Mat. in Civ. Engrg., ASCE, 7(4), 252–257.
5.
Benmokrane, B., Chaallal, O., and Masmoudi, R. ( 1996). “Flexural response of concrete beams reinforced with FRP reinforcing bars.” ACI Struct. J., 91(2), 46–55.
6.
Brown, L. V., and Bartholomew, L. C. ( 1993). “FRP reinforcing bars in reinforced concrete members.” ACI Mat. J., 90(1), 34–39.
7.
Goodspeed, C., Schmeckpeper, E., Yost, J. R., and Gross, T. ( 1990). “Fiber reinforced plastic grids for the structural reinforcement of concrete.” Proc., 1st Mat. Engrg. Congr., ASCE, New York, 593–604.
8.
Hughes Brothers, Inc. ( 1997). “Glass fiber reinforced polymer rebar.” Product brochure, Seward, Nebr.
9.
Marshall Industries Composites, Inc. “C-Bar;tm reinforcing rods for concrete reinforcement.” Product brochure, Lima, Ohio.
10.
Masmoudi, R., Theriault, M., and Benmokrane, B. ( 1998). “Flexural behavior of concrete beams reinforced with deformed fiber reinforced plastic reinforcing rods.” ACI Struct. J., 95(6), 665–675.
11.
NEFCOM Corporation. ( 1988). “NEFMAC—Technical leaflet 1, new fiber composite material for reinforcing concrete.” Tokyo.
12.
NEFCOM Corporation. ( 1990). “Mechanical properties of NEFMAC.” Tokyo, June.
13.
New Hampshire Department of Transportation. ( 1983). “Standard specifications for road and bridge construction, Section 520 concrete and masonry.” Technical specification, Concord, N.H.
14.
Rajagopalan, K. S., and Ferguson, P. M. ( 1968). “Exploratory shear tests emphasizing percentage of longitudinal steel.” ACI J., August, 634–638.
15.
Schmeckpeper, E. R. ( 1992). “Performance of concrete beams and slabs reinforced with FRP grids.” PhD dissertation, University of New Hampshire, Durham, N.H.
16.
Stetson, M. B., and Goodspeed, C. H. ( 1992). “Fundamental considerations in the design of flexural concrete members with non-prestressed FRP reinforcement.” Proc., 1st Int. Conf. on Advanced Compos. Mat. in Bridges and Struct., Sherbrooke, PQ, Canada.
Information & Authors
Information
Published In
History
Received: Jun 29, 1999
Published online: Feb 1, 2001
Published in print: Feb 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.