Removal of Oil and Grease and Chemical Oxygen Demand from Oily Automotive Wastewater by Adsorption after Chemical De-emulsification
Publication: Practice Periodical of Hazardous, Toxic, and Radioactive Waste Management
Volume 7, Issue 3
Abstract
US EPA has proposed new categorical pretreatment standards for the wastewater generated by the Metal Products and Machinery industry, which includes all automotive plants. The oil and grease (O&G) standard (17 mg/L monthly average) is one to two orders of magnitude lower than Ford’s current discharge limits. The rationale for this low standard is to remove most organics from the wastewater. Most engine and transmission plants will not meet the standard without modification. Therefore, adsorption was studied as an add-on option to polish the effluent from the existing treatment process, either chemical de-emulsification or ultrafiltration. Five adsorbents (powdered activated carbon, anthracite, and three modified clay adsorbents) were investigated by developing adsorption isotherms for O&G and chemical oxygen demand (COD) using wastewater collected from a Ford plant. Activated carbon had the highest adsorption capacity, whereas anthracite had the lowest. For a typical O&G concentration range (0 to 30 mg/L) expected in the effluent after chemical de-emulsification or ultrafiltration, activated carbon was found to outperform all clay adsorbents studied by over an order of magnitude in terms of both adsorption capacity and costs. The removal of COD via adsorption showed a trend similar to that of O&G.
Get full access to this article
View all available purchase options and get full access to this article.
References
Adamson, A. W. (1967). Physical chemistry of surface, 2nd Ed., Interscience–Wiley, New York.
American Public Health Association (1998). Standard methods for the examination of water and wastewater, 20th Ed., American Water Works Association and Water Environment Federation, Washington, D.C.
Biomin. (Undated). “EC-100, The carbon booster.” Biomin, Inc. Tech. Bull., Ferndale, Mich.
Bridié, A. L., Wolff, C. J. M., and Winter, M.(1979). “BOD and COD of Some Petrochemicals.” Water Res., 13, 627.
Calgon Corporation (1976). “Filtrasorb® 300 and 400 granular activated carbon for potable water treatment.” Calgon Corporate Tech. Bull.
Calgon Corporation. (Undated). “Pulverized activated carbons.” Calgon Corporate Tech. Bull.
Horiba Instruments. (1994). “Instruction manual OCMA-220 oil content analyzer.” Horiba Manual No. 091279, February 1989, Revised: September 1994, Horiba Instruments Inc., Irvine, Calif.
Kim, B. R., Gaines, W. A., Szafranski, M., Bernath, E., and Miles, A. M.(2002). “Removal of heavy metals from automotive wastewater by sulfide precipitation.” J. Environ. Eng., 128(7), 612–623.
Kim, B. R.et al. (1998). “Evaluation of commercial ultrafiltration systems for treating automotive oily wastewater.” Water Environ. Res., 70, 1280.
Luthy, R. G., Selleck, R. E., and Galloway, T. R.(1977). “Surface properties of petroleum refinery waste oil emulsions.” J. Water Pollut. Control Fed., 11, 1211.
Luthy, R. G., Selleck, R. E., and Galloway, T. R.(1978). “Removal of emulsified oil with organic coagulants and dissolved air flotation.” J. Water Pollut. Control Fed., 12, 331.
U.S. Environmental Protection Agency (U.S. EPA). (1994). “Methods for the determination of metals in environmental samples supplement I.” U.S. EPA, Environmental Monitoring Systems Laboratory (EMSL), Cincinnati, EPA-600/R-94/111.
U.S. Environmental Protection Agency. (1995). “Effluent limitations guidelines, pretreatment standards, and new source performance standards: Metal products and machinery; proposed rule.” Federal Register, 60 (No. 103; May 30), 40 CFR part 433, 438, and 464.
U.S. Environmental Protection Agency. (2000). “Development document for the proposed effluent limitations guidelines and standards for the metal products and machinery point source category.” EPA-821-B-00-005, Office of Water, Washington, D.C.
Information & Authors
Information
Published In
Copyright
Copyright © 2003 American Society of Civil Engineers.
History
Received: Jul 1, 2002
Accepted: Mar 24, 2003
Published online: Jun 13, 2003
Published in print: Jul 2003
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.