Calibration of Reliability-Based Resistance Factors for Flush Drilled Soil Anchors in Taipei Basin
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 134, Issue 9
Abstract
The goal of this research is to calibrate the reliability-based resistance factor of flush drilled soil anchors for their ultimate pullout capacities based on in situ anchor pullout test data in the alluvial soil underlying the Taipei Basin. Efforts are taken to quantify the uncertainties with a full probabilistic analysis approach. The resistance factor is calibrated based on the in situ test results of 46 anchors with a rigorous theoretical approach which constructs the relationship between the resistance factor and failure probability. With this relationship, the reliability corresponding to the code regulation can be verified. From the results of the analysis, it is found that the borehole enlargement due to the flush drilling is quite significant: the actual diameter of the fixed anchor end may be much larger than the nominal diameter of the drilling casing. Consequently, the safety factor of 3.0, recommended by most anchor codes, is found to be too conservative. The results should be valuable for reliability-based design of flush drilled soil anchors in the Taipei Basin.
Get full access to this article
View all available purchase options and get full access to this article.
References
Ang, A. H. S., and Tang, W. H. (1975). Probability concepts in engineering planning and design: Basic principles, Vol. 1, Wiley, New York.
Bea, R. G., Jin, Z., Valle, C., and Ramos, R. (1999). “Evaluation of reliability of platform pile foundations.” J. Geotech. Geoenviron. Eng., 125(8), 696–704.
Chalermyanont, T., and Benson, C. H. (2004). “Reliability-based design for internal stability of mechanically stabilized earth walls.” J. Geotech. Geoenviron. Eng., 130(2), 163–173.
Chowdhury, R., and Flentje, P. (2003). “Role of slope reliability analysis in landslide risk management.” Bull. Eng. Geol. Environ., 62(1), 41–46.
Christian, J. T., Ladd, C. C., and Gregory, B. B. (1994). “Reliability applied to slope stability analysis.” J. Geotech. Engrg., 120(12), 2180–2207.
Fenton, G. A., and Griffiths, D. V. (2003). “Bearing capacity prediction of spatially random c- soils.” Can. Geotech. J., 40(1), 54–65.
Federal Highway Administration (FHwA). (1998). Load and resistance factor design for highway bridge substructures, Publication No. FHWA HI-98-032, U.S. Department of Transportation, Washington, D.C.
Fenton, G. A, Griffiths, D. V., and Williams, M. B. (2005). “Reliability of traditional retaining wall design.” Geotechnique, 55(1), 55–62.
FIP Commission on Practical Construction. (1982). Recommendations for the design and construction of prestressed concrete grout anchors, Wexham Springs.
Gelman, A., Carlin, J. B., Stern, H. S., and Rubin, D. B. (2000). Bayesian data analysis, Chapman and Hall, London.
Geman, S., and Geman, D. (1984). “Stochastic relaxation, Gibbs distribution and the Bayesian restoration of images.” IEEE Trans. Pattern Anal. Mach. Intell., 6, 721–741.
Gilks, W. R., Spiegelhalter, D. J., and Richardson, S. (1996). Markov chain Monte Carlo in practice, Chapman and Hall, London.
Hawkes, J. M., and Evans, R. H. (1951). “Bond stresses in reinforced concrete columns and beams.” Struct. Eng., 29(12), 323–328.
Liao, H. J., Ou, C. D., and Shu, S. C. (1996). “Anchorage behavior of shaft anchors in alluvial soil.” J. Geotech. Engrg., 122(7), 526–533.
Low, B. K. (2005). “Reliability-based design applied to retaining walls.” Geotechnique, 55(1), 63–75.
Low, B. K., Gilbert, R. B., and Wright, S. G. (1998). “Slope reliability analysis using general method of slices.” J. Geotech. Geoenviron. Eng., 124(4), 350–362.
McVay, M., and Kuo, C., Guisinger, A. L. (2003). “Calibrating resistance factors for load and resistance factor design for statnamic load testing.” Final Rep. No. 4910-4504-823-12, Florida Department of Transportation, Tallahassee, Fla.
Metropolis, N., Rosenbluth, A. E., Rosenbluth, M. N., Teller, A. H., and Teller, E. (1953). “Equation of state calculations by fast computing machines.” J. Chem. Phys., 21, 1087–1092.
Moh and Associates. (1987). “Engineering properties of the soil deposits in the Taipei Basin.” Rep. No. 85043, Ret-Ser Engineering Agency and Taipei Public Works Dept., Taipei, China (in Chinese).
Paikowsky, S. G., et al. (2004). “Load and resistance factor design (LRFD) for deep foundations.” NCHRP Rep. No. 507, Transportation Research Board, Washington, D.C.
Phoon, K. K. (1995). Reliability-based design of foundations for transmission line structures.” Ph.D. dissertation, Cornell Univ., Ithaca, N.Y.
Phoon, K. K., Kulhawy, F. H., and Grigoriu, M. D. (2003). “Development of a reliability-based design framework for transmission line structure foundations.” J. Geotech. Geoenviron. Eng., 129(9), 798–806.
Zhang, L. M., Tang, W. H., and Ng, C. W. W. (2001). “Reliability of axially loaded driven pile groups.” J. Geotech. Geoenviron. Eng., 127(12), 1051–1060.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: May 28, 2007
Accepted: Dec 12, 2007
Published online: Sep 1, 2008
Published in print: Sep 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.