Impact of Routine Quality Assurance on Reliability of Bored Piles
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 132, Issue 5
Abstract
Quality assurance (QA) tests, such as integrity tests, are routinely conducted to ensure the safety of pile foundations. QA tests provide additional information and result in changes in estimated reliability of pile foundations. This paper aims to formalize a procedure to quantitatively evaluate the impact of routine QA tests on the reliability of pile foundations. Three cases of reliability analyses based on interface coring of large-diameter bored piles are studied; namely, no toe debris detected, toe debris detected without repair, and toe debris detected and repaired. The prior information of the occurrence probability and thickness of toe debris is established based on a practice survey and accumulated QA data. The Bayesian approach is then applied to update the occurrence probability and the mean toe debris thickness based on outcomes of on-site QA tests and remedial actions taken after these QA tests. Subsequently, the reliability of the piles can be updated. The updated reliability can be significantly higher than that before the QA tests. The degree of reliability improvement depends on the pile specifics, the outcomes from the QA tests, and the remedial actions taken after the QA tests.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was substantially supported by a grant from the Research Grants Council of the Hong Kong Special Administrative Region (Project No. HKUST6035/02E). The writers would like to thank Mr. Eric Y. W. Wong, MPhil Research Assistant, for conducting the practice survey on quality assurance for bored piles.
References
Ang, A. H.-S., and Tang, W. H. (1975). Probability concepts in engineering planning and design, Vol. 1, Wiley, New York.
ASCE Committee on Fatigue and Fracture Reliability of the Committee on Structural Safety and Reliability of the Structural Division (CFFR). (1982). “Fatigue reliability: Quality assurance and maintainability.” J. Struct. Div. ASCE, 108(1), 25–46.
Baecher, G. R., and Rackwitz, R. (1982). “Factors of safety and pile load tests.” Int. J. Numer. Analyt. Meth. Geomech., 6(4), 409–424.
Baker, C. N., Drumright, E. E., Briaud, J. L., Mensah, F. D., and Parikh, G. (1993). “Drilled shafts for bridge foundations.” Rep. No. FHWA-RD-92-004, Federal Highway Administration, Washington, D.C.
Bea, R. G. (2003). “Quality, reliability and human factors in deepwater drilling and production.” Proc., 21st Int. Conf. on Offshore Mech., and Arctic Eng. (CD-ROM), ASME, New York.
Buildings Department. (2000). Practice note for authorized persons and registered structural engineers 66 (PNAP 66), pile foundations, Buildings Dept., Hong Kong.
Hassan, K. M., and O’Neill, M. W. (1998). “Structural resistance factors for drilled shafts with minor defects.” Final Rep., Phase I, Dept. of Civil and Environmental Eng., Univ. of Houston, Houston.
Hoit, M. I., McVay, M. C., Hays, C. O., and Williams, M. (2001). FB-Pier users guide and manual, Univ. of Florida, Gainesville, Fla.
Hong Kong Construction Association Ltd., Piling Contractors Committee (HKCA). (2003). Study for bored pile interface acceptance criteria, prepared by Ove Arup & Partners Hong Kong Ltd., Hong Kong.
Kay, J. N. (1976). “Safety factor evaluation for single piles in sand.” J. Geotech. Eng. Div., Am. Soc. Civ. Eng., 102(10), 1093–1108.
Kong, L. G., and Zhang, L. (2004). “Lateral or torsional failure modes in vertically loaded defective pile groups.” GeoSupport 2004, Drilled shafts, micropiling, deep mixing, remedial methods, and specialty foundation systems, Geotechnical Special Publication No. 124, J. P. Turner and P. W. Mayne, eds., ASCE, Reston, Va., 625–636.
Lacasse, S., and Goulois, A. (1989). “Uncertainty in API parameters for predictions of axial capacity of driven piles in sand.” Proc., 21st Offshore Technology Conf., Society of Petroleum Engineers, Richardson, Tex., 353–358.
Lam, W. Y. (2004). “Reliability of bored piles with defects.” Final Year Rep., Dept. of Civil Engineering, The Hong Kong Univ. of Science and Technology, Hong Kong.
Mcvay, M. C., Kuo, C. L., and Singletary, W. A. (1998). “Calibrating resistance factors in the load and resistance factor design for Florida foundations.” Final Rep., Dept. of Civil Engineering, Univ. of Florida, Gainesville.
McVay, M. C., Townsend, F. C., and Williams, R. C. (1992). “Design of socketed drilled shafts in limestone.” J. Geotech. Eng., 118(10), 1626–1637.
Moan, T., Vardal, O. T., Hellevig, N. C., and Skjoldli, K. (2000). “Initial crack depth and POD values inferred from in-service observations of cracks in North Sea jackets.” J. Offshore Mech. Arct. Eng., 122(3), 157–162.
O’Neill, M. W., and Reese, L. C. (1999). “Drilled shafts: Construction procedures and design methods.” Publ. No. FHWA-IF-99–025, Federal Highway Administration, Office of Implementation, McLean, Va.
O’Neill, M. W., and Sarhan, H. A. (2004). “Structural resistance factors for drilled shafts considering construction flaws.” Current practices and future trends in deep foundations, Geotechnical Specical Publication No. 125, J. A. DiMaggio and M. H. Hussein, eds., ASCE, Reston, Va., 166–185.
Poulos, H. G. (1997). “Analysis of pile groups with defect piles.” Proc., 14th Int. Conf. on Soil Mechanics and Foundation Engineering, Hamburg, A. A. Balkema, Rotterdam, The Netherlands, 871–876.
Raiffa, H., and Schlaifer, R. (2000). Applied statistical decision theory, Wiley, New York.
Reese, L. C., and O’Neill, M. W. (1988). “Drilled shafts: Construction procedures and design methods.” Rep. No. FHWA-HI-88–042, U.S. Dept. of Transportation, Washington, D.C.
Shinozuka, M., and Yang, J. N. (1969). “Optimum structural design based on reliability and proof load test.” Proc., 8th Reliability and Maintainability Conf., Vol. 8, 375–391.
Withiam, J. L., et al. (2001). “Load and resistance factor design (LRFD) for highway bridge substructures.” Rep. No. FHWA HI-98-032, Federal Highway Administration, Washington, D.C.
Wong, Y. W. (2004). “Behaviors of large diameter bored pile groups with defects.” M.Phil. thesis, the Hong Kong Univ. of Science and Technology, Hong Kong.
Zhang, L. M. (2004). “Reliability verification using proof pile load tests.” J. Geotech. Geoenviron. Eng., 130(11), 1230–1213.
Zhang, L. M., and Tang, W. H. (2002). “Use of load tests for reducing pile length.” Proc., Int. Deep Foundations Congress, Geotechnical Special Publication No. 116, M. W. O’Neill and F. C. Townsend, eds., ASCE, Reston, Va., 993–1005.
Zhao, Z. W., Haldar, A., and Breen, F. L., Jr. (1992). “Fatigue-reliability updating through inspection of steel bridges.” J. Struct. Eng., 120(5), 1624–1641.
Zheng, R. H., and Ellingwood, B. (1998). “Role of nondestructive evaluation in time-dependent reliability analysis.” Struct. Safety, 20(4), 325–339.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Feb 8, 2005
Accepted: Oct 27, 2005
Published online: May 1, 2006
Published in print: May 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.