Drained and Undrained Strength Interpretation for Low-Plasticity Silts
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 132, Issue 2
Abstract
The engineering behavior of low-plasticity silts is more difficult to characterize than is the behavior of clay or sand. Due to their tendency to dilate during shear, establishing a consistent and practically useful failure criterion for low-plasticity silts can be very difficult. Consideration of how the undrained shear strength of silt is related to changes in pore pressure provides a more useful and practical framework for understanding the undrained strengths of these materials and for characterizing undrained strengths for practical purposes. Using a value of Skempton’s as a failure criterion has been found to result in very reasonable values of undrained strength and to reduce scatter in the results as compared to using other criteria. Using a failure criterion based on an appropriate value of results in consistent values of , and tolerably small values of strain at failure. For low-plasticity, dilative silts that pose the greatest problems with respect to definition of “failure,” using as a failure criterion is an appropriate and simple choice.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research described in this paper was funded by the U.S. Army Corps of Engineers under Contract No. DACW39-89-M-2985. The project began in 1989, and the results presented in this paper were obtained from 1989 to 1994. The project director was Dr. Vic Torrey, who has since retired from the Corps of Engineers. Mr. Jeff Huffman assisted in the laboratory testing reported.
References
Abdel-Haq, A., and Hryciw, R. D. (1998). “Ground settlement in Simi Valley following the Northridge earthquake.” J. Geotech. Geoenviron. Eng., 124(1), 80–89.
American Society of Testing and Materials (ASTM). (1995a). “Standard test method for consolidated-undrained triaxial compression test on cohesive soils.” ASTM D4767, ASTM book of standards, Volume 4.08: Construction: Soil and rock, West Conshohocken, Pa.
American Society of Testing and Materials (ASTM). (1995b). “Standard test methods for unconsolidated, undrained triaxial compression test on cohesive soils.” ASTM D2850, ASTM book of standards, Volume 4.08: Construction: Soil and rock, West Conshohocken, Pa.
Bishop, A. W., and Eldin, G. (1950). “Undrained triaxial tests on saturated sands and their significance in the general theory of shear strength.” Geotechnique, 2, 13–32.
Börgesson, L. (1981). “Shear strength of inorganic silty soils.” Proc., 10th Int. Conf. on Soil Mechanics and Foundation, Stockholm, 10(1), 567–572.
Boulanger, R. W., Mejia, L. H., and Idriss, I. M. (1997). “Liquefaction at Moss Landing during Loma Prieta earthquake.” J. Geotech. Geoenviron. Eng., 123(5), 453–468.
Fleming, L. N., and Duncan, J. M. (1990). “Stress-deformation characteristics of an Alaskan silt.” J. Geotech. Eng., 116(3), 377–393.
Golder, H. Q., and Skempton, A. W. (1948). “The angle of shearing resistance in cohesive soils for tests at constant water content.” Proc., 2nd Int. Conf. on Soil Mechanics and Foundation Engineering, 1, Rotterdam, The Netherlands, 185–192.
Høeg, K., Dyvik, R., and Sandbækken, G. (2000). “Strength of undisturbed versus reconstitutued silt and silty sand specimens.” J. Geotech. Geoenviron. Eng., 126(7), 606–617.
Konrad, J. M., Bozozuk, M., and Law, K. T. (1984). “Study of in situ test methods in deltaic silt.” Proc., 11th Int. Conf. on Soil Mechanics and Foundation Engineering, Vol. 2, 879–886.
Lunne, T., Robertson, P. K., and Powell, J. J. M. (1997). Cone penetration testing in geotechincal practice, Blackie Academic and Profession, London.
Nash, K. L. (1953). “The shearing resistance of a fine closely graded sand.” Proc., 3rd Int. Conf. on Soil Mechanics and Foundation Engineering, 1, Zurich, Switzerland, 160–164.
Penman, A. D. M. (1953). “Shear characteristics of a saturated silt measured in triaxial compression.” Geotechnique, 3, 312–328.
Senneset, K., Janbu, N., and Svanø, G. (1982). “Strength and deformation parameters from cone penetration tests.” Proc., 2nd European Symposium on Penetration Testing, ESOPT-II, Amsterdam, Vol. 2, 863–870.
Skempton, A. W. (1954). “The pore pressure coefficients A and B.” Geotechnique, 4, 143–147.
Skempton, A. W. and Bishop, A. W. (1954). “Soils.” Building materials: Their elasticity and inelasticity, M. Reiner and A. G. Ward, eds., North-Holland, Amsterdam, 417–482.
Torrey, V. H. (1982). Laboratory shear strength of dilative silts, Report prepared for the Lower Mississippi Valley Division, U. S. Army Engineers Waterways Experiment Station, Vicksburg, Miss.
Wang, J. L., and Vivatrat, V. (1982). “Geotechnical properties of Alaska OCS silts.” Proc., 14th Annual Offshore Technology Conf., OTC 4412, Houston, Tex., 415–420.
Youd, T. L., and Bennett, M. J. (1983). “Liquefaction sites, Imperial Valley, California.” J. Geotech. Eng., 109(3), 440–457.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Mar 31, 2004
Accepted: Apr 18, 2005
Published online: Feb 1, 2006
Published in print: Feb 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.