Development of an Equivalent Homogenous Fluid Model for Pseudo-Two-Phase Flow through Fractured Rock
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 131, Issue 7
Abstract
Fracture flow of two-phase mixtures is particularly applicable to the coal mining and coal bed methane projects in Australia. A one-dimensional steady-state pseudo-two-phase flow model is proposed for fractured rock. The model considers free flow of a compressible mixture of air and water in an inclined planar fracture and is based upon the conservation of momentum and the “cubic” law. The flow model is coupled to changes in the stress environment through the fracture normal stiffness, which is related to changes in fracture aperture. The model represents the individual air and water phases as a single equivalent homogenous fluid. Laboratory testing was performed using the two-phase high-pressure triaxial apparatus on 54 mm diameter (approximately ) borehole cores intersected by induced near-axial fractures. The samples were of Triassic arenaceous fine-medium grained sandstone (known as the Eckersley Formation) that is found locally in the Southern Coalfield of New South Wales. The sample fracture roughness was assessed using a technique based upon Fourier series analysis to objectively attribute a joint roughness coefficient. The proposed two-phase flow model was verified using the recorded laboratory data obtained over a range of triaxial confining pressures (i.e., fracture normal stresses).
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Acknowledgement of essential contributions to this research project should include the financial supporters, namely the Australian Research Council (ARC), and Strata Control Technology (SCT). Further assistance was obtained from New Dawn 3D who provided specialist advice on the surface laser scanning of the rock samples, and a special debt of gratitude is owed to the technical staff at the university.
References
Barton, N., Bandis, S. and Bakhtar, K. (1985). “Strength, deformation, and conductivity coupling of rock joints.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 22, 121–140.
Bendat, J. S., and Piersol, A. G. (1986). “Random data: Analysis and measurement procedures., 2nd Ed., Wiley, New York, 566.
Fourar, M., Bories, S., Lenormand, R., and Persoff, P. (1993). “Two-phase flow in smooth and rough fractures: Measurements and correlation by porous medium and pipe flow models.” Water Resour. Res., 29:11, 3699-3708.
Fredlund, D. G., and Rahardjo, H. (1993). Soil mechanics for unsaturated soils, Wiley, New York, 571.
Indraratna, B., and Haque, A. (1999). “Triaxial equipment for measuring the permeability and strength of intact and fractured rocks.” Geotechnique, 49(4), 515–521.
Indraratna, B., Price, J., and Gale, W. (2002). “Fourier description of fracture roughness.” Proc., 5th North American Rock Mechs Symp., Hammah et al., eds., University of Toronto Press, Toronto, 35–44.
Indraratna, B. and Ranjith, P. (2001a). Hydromechanical aspects and unsaturated flow in jointed rock., A. A. Balkema, Lisse, 286.
Indraratna, B., and Ranjith, P. G. (2001b). “Laboratory measurement of two-phase flow parameters in rock joints based on high pressure triaxial testing.” J. Geotech. Geoenviron. Eng., 127(6), 530–542.
Indraratna, B., Ranjith, P. G., Price, J. R., and Gale, W. (2003). Two-phase (air and water) flow through rock joints: Analytical and experimental study.” J. Geotech. Geoenviron. Eng., 129(10), 918–928.
International Society for Rock Mechanics (ISRM). (1978). “Suggested methods for the quantitative description of discontinuities in rock masses. Part 1.” Site characterization, rock characterization testing and monitoring, ISRM Suggested Methods. E. T. Brown, ed., Commission on Testing Methods, Pergamon, N.Y.
McAdams, W. H. (1942). “Vaporization in horizontal tubes II benzene—Oil mixtures.” Trans. ASME 64, 163
[cited in Wallis G. B., (1969)].
Persoff, P., and Pruess, K. (1993). “Flow visualisation and relative permeability measurements in rough walled fractures.” Proc., 4th Annual Int. High Level Radioactive Waste Management Conference, American Nuclear Society, La Grange Park, Ill., 2033–2041.
Price, J. (2005). “Coupled two-phase air and water flow in rough fractures.” PhD thesis, Univ. of Wollongong, Wollongong City, New South Wales, Australia.
Priest, S. D. (1993). Discontinuity analysis for rock engineering., Chapman‐Hall, London, 473.
Vennard, J. K., and Street, R. L. (1982). Elementary fluid mechanics, 6th Ed. Wiley, New York, 689.
Wallis, G. B. (1969). One-dimensional two-phase flow, McGraw‐Hill, New York, 408.
Witherspoon, P. A., Wang, J. S. Y., Iwai, K., and Gale J. (1980). “Validity of cubic law for fluid flow in a deformable rock fracture.” Water Resour. Res., 16(6), 1016–1024.
Yang, Z. Y., and Di, C. C. (2001). “A directional method for directly calculating the fractal parameters of joint surface roughness.” Int. J. Rock Mech. Min. Sci., 38, 1201–1210.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Apr 12, 2004
Accepted: Sep 25, 2004
Published online: Jul 1, 2005
Published in print: Jul 2005
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.