Reliability Verification Using Proof Pile Load Tests
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 130, Issue 11
Abstract
Proof pile load tests are an important means to cope with uncertainties in the design and construction of pile foundations. In this paper, a systematic method to incorporate the results of proof load tests not conducted to failure into the design of pile foundations is developed. In addition, illustrative acceptance criteria for driven piles based on proof load tests are proposed for use in a reliability-based design. Finally, modifications to conventional proof test procedures are studied so that the value derived from proof tests can be maximized. Whether or not a proof test is conducted to failure, its results can be used to update the probability distribution of the pile capacity using the method proposed in this paper. Hence, contributions of the proof test can be included in foundation design in a logical manner by considering several load test parameters such as the number of tests, the test load, the factor of safety, and test results. This adds value to proof load tests and warrants improvements in the procedures for acceptance of pile foundations using proof load tests. A larger test load for proof tests, say 1.5 times the predicted pile capacity, is recommended since it will yield more information about the capacity statistics and thus allow for more economical designs.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Association of State Highway and Transportation Officials (AASHTO). ( 1997). LRFD bridge design specifications, American Association of State Highway and Transportation Officials, Washington, D.C.
2.
Ang, A.H-S., and Tang, W.H. ( 1975). Probability concepts in engineering planning and design, Vol. 1, Basic principles, Wiley, New York.
3.
Baecher, G. R., and Rackwitz, R. (1982). “Factors of safety and pile load tests.” Int. J. Numerical and Analytical Methods in Geomechanics, 6(4), 409–424.
4.
Barker, R. M, et al. ( 1991). Manuals for the design of bridge foundations, NCHRP Report 343, Transportation Research Board, National Research Council, Washington, D.C.
5.
Bea, R. G., Jin, Z., Valle, C., and Ramos, R. (1999). “Evaluation of reliability of platform pile foundations.” J. Geotech. Geoenviron. Eng., 125(8), 696–704.
6.
Becker, D. E. (1996a). “Eighteenth Canadian geotechnical colloquium: Limit states design for foundations. I: An overview of the foundation design process.” Can. Geotech. J., 33(6), 956–983.
7.
Becker, D. E. (1996b). “Eighteenth Canadian geotechnical colloquium: Limit states design for foundations. II: Development for the national building code of Canada.” Can. Geotech. J., 33(6), 984–1007.
8.
British Standards Institution (BSI). ( 1986). “British standard code of practice for foundations.” BS 8004, British Standards Institution, London.
9.
Buildings Department of Hong Kong (BD). ( 2002). Pile foundations-Practice notes for authorized persons and registered structural engineers, PNAP66, Buildings Department, Hong Kong.
10.
Duncan, J. M. (2000). “Factors of safety and reliability in geotechnical engineering.” J. Geotech. Geoenviron. Eng., 126(4), 307–316.
11.
Geotechnical Engineering Office (GEO). ( 1996). Pile design and construction, GEO Publication 1/96, Geotechnical Engineering Office, Hong Kong.
12.
Hannigan, P. J., Goble, G. G., Thendean, G., Likins, G. E., and Rausche, F. ( 1997). Design and construction of driven pile foundations, Workshop manual, Vol. 1, Publication No. FHWA-HI-97-014, Federal Highway Administration, Washington, D.C.
13.
Hirany, A., and Kulhawy, F.H. ( 1989). “Interpretation of load tests on drilled shafts-Part 1: Axial compression.” Proc., Foundation Engineering: Current Principles and Practices, Vol. 2, F. H. Kulhawy, ed., ASCE, New York, 1132–1149.
14.
International Society of Soil Mechanics and Foundation Engineering (ISSMFE) Subcommittee on Field and Laboratory Testing. (1985). “Axial pile loading test. I: Static loading.” Geotech. Test. J., 8(2), 79–89.
15.
Kay, J. N. (1976). “Safety factor evaluation for single piles in sand.” J. Geotech. Eng. Div., Am. Soc. Civ. Eng., 102(10), 1093–1108.
16.
Lacasse, S., and Goulois, A. ( 1989). “Uncertainty in API parameters for predictions of axial capacity of driven piles in sand.” Proc., 21st Offshore Technology Conference, Society of Petroleum Engineers, Richardson, Tex., 353–358.
17.
Malone, A.W. ( 1992). “Piling in tropic weathered granite.” Proc., Int. Conf. on Geotechnical Engineering, Malaysia Technological University, Johor Bahru, 411–457.
18.
McVay, M. C., Birgisson, B., Zhang, L. M., Perez, A., and Putcha, S. (2000). “Load and resistance factor design (LRFD) for driven piles using dynamic methods—A Florida perspective.” Geotech. Test. J., 23(1), 55–66.
19.
Meyerhof, G. G. (1970). “Safety factors in soil mechanics.” Can. Geotech. J., 7(4), 349–355.
20.
Meyerhof, G. G. (1976). “Bearing capacity and settlement of pile foundations.” J. Geotech. Eng. Div., Am. Soc. Civ. Eng., 102(3), 195–228.
21.
Ng, C. W. W., Li, J. H. M., and Yau, T. L. Y. (2001a). “Behavior of large diameter floating bored piles in saprolitic soils.” Soils Found., 41(6), 37–52.
22.
Ng, C. W. W., Yau, T. L. Y., Li, J. H. M., and Tang, W. H. (2001b). “New failure load criterion for large diameter bored piles in weathered geomaterials.” J. Geotech. Geoenviron. Eng., 127(6), 488–498.
23.
National Research Council of Canada (NRC). ( 1995). National building code of Canada, National Research Council Canada, Ottawa.
24.
O’Neill, M. W., and Reese, L. C. ( 1999). “Drilled shafts: Construction procedures and design methods.” Pub. No. FHWA-IF-99-025, Federal Highway Administration, Washington, D.C.
25.
Orchant, C.J., Kulhawy, F.H., and Trautmann, C.H. ( 1988). “Reliability-based foundation design for transmission line structures, Vol. 2: Critical evaluation of in situ test methods.” EL-5507 Final Report, Electrical Power Institute, Palo Alto, Calif.
26.
Paikowsky, S.G. ( 2002). “Load and resistance factor design (LRFD) for deep foundations.” Foundation Design Codes -Proc. IWS Kamakura 2002, Y. Honjo, O. Kusakabe, K. Matsui, M. Kouda, G. Pokharel, (eds.), Balkema, Rotterdam, The Netherlands, 59–94.
27.
Paikowsky, S.G., and Stenersen, K.L. ( 2000). “The performance of the dynamic methods, their controlling parameters and deep foundation specifications.” Proc., 6th Int. Conf. on the Application of Stress-Wave Theory to Piles. S. Niyama and J. Beim, eds, Balkema, Rotterdam, 281–304.
28.
Passe, P., Knight, B., and Lai, P. ( 1997). “Load tests.” FDOT Geotech. News, Vol. 7, P. Passe, ed., Florida Dept. of Transportation, Tallahassee, Fla.
29.
Peck, R. B. (1969). “Advantages and limitations of the observational method in applied soil mechanics.” Geotechnique, 19(2), 171–187.
30.
Phoon, K. K., Kulhawy, F. H., and Grigoriu, M. D. (2000). “Reliability-based design for transmission line structure foundations.” Computers and Geotech., 26(3–4), 169–185.
31.
Schmertmann, J.H. ( 1978). “Guidelines for cone penetration test, performance, and design.” Rep. No. FHWA-TS-78-209, Federal Highway Administration, Washington, D.C.
32.
Sidi, I.D. ( 1985). “Probabilistic prediction of friction pile capacities.” Ph.D. thesis, University of Illinois at Urbana, Ill.
33.
Tang, W.H. ( 1989). “Uncertainties in offshore axial pile capacity.” Proc., Foundation Engineering, Geotechnical Special Publication No. 27, Vol. 2., F. H. Kulhawy, ed., ASCE, New York, 833–847.
34.
Tang, W.H., and Gilbert, R.B. ( 1993). “Case study of offshore pile system reliability.” Proc., 25th Offshore Technology Conference, Society of Petroleum Engineers, Richardson, Tex., 677–686.
35.
United States Army Corps of Engineers (USACE). (1993). Design of pile foundations, ASCE, New York.
36.
Whitman, R. V. (1984). “Evaluating calculated risk in geotechnical engineering.” J. Geotech. Eng., 110(2), 145–188.
37.
Withiam, J.L., et al. ( 2001). “Load and resistance factor design (LRFD) for highway bridge substructures.” Report No. FHWA HI-98-032, Federal Highway Administration, Washington, D. C.
38.
Wu, T. H., Tang, W. H., Sangrey, D. A., and Baecher, G. B. (1989). “Reliability of offshore foundations: State of the art.” J. Geotech. Eng., 115(2), 157–178.
39.
Zhang, L.M., and Tang, W.H. ( 2001). “Bias in axial capacity of single bored piles arising from failure criteria.” Proc. ICOSSAR’2001, Int. Association for Structural Safety and Reliability, R. Crotis, G. Schuller, and M. Shinozuka, eds., Balkema, Rotterdam, The Netherlands, (CD Rom).
40.
Zhang, L. M., Tang, W. H., and Ng, C. W. W. (2001). “Reliability of axially loaded driven pile groups.” J. Geotech. Geoenviron. Eng., ASCE, 127(12), 1051–1060.
41.
Zhang, L.M., and Tang, W.H. ( 2002). “Use of load tests for reducing pile length.” Proc., Int. Deep Foundations Congress, Geotechnical Special Publication No. 116, M. W. O’Neill and F. C. Townsend, eds., ASCE, Reston, Va., 993–1005.
42.
Zhang, L.M., Shek, M.P., Li, P.H., and Ng, M.Y. ( 2003). “Development of a Hong Kong driven pile database.” Internal Rep., Dept. of Civil Engineering, Hong Kong Univ. of Science and Technology, Hong Kong.
43.
Zhang, L. M., Tang, W. H., Zhang, L. L., and Zheng, J. G. (2004). “Reducing uncertainty of prediction from empirical correlations.” J. Geotech. Geoenviron. Eng., 130(5), 526–534.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 ASCE.
History
Published online: Oct 15, 2004
Published in print: Nov 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.