Shaft Resistance of Single Vertical and Batter Piles Driven in Sand
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 129, Issue 7
Abstract
An experimental investigation of the shaft resistance of single vertical and batter piles pushed into sand was conducted. A prototype laboratory setup was designed for testing relatively large model piles, inclined at an angle that varied between zero and 30° with the vertical. Two model piles having diameters of 38 and 76 mm were tested at a ratio of the pile’s length to diameter up to 40, and subjected to axial compression loading. The pile models were instrumented to allow direct measurements of the shaft resistance. A theoretical model was developed to take into account the asymmetrical earth pressure distribution around the pile shaft, the level of mobilization of the angle of friction between the pile shaft and the sand, and the pile diameter. The results predicted by the theory developed agreed well with the experimental results of the present investigation as well as other experimental and field results available in the literature. Design charts are presented for use in practice. The results of the present investigation support the concept of the critical depth for the shaft resistance of vertical and batter piles driven in sand.
Get full access to this article
View all available purchase options and get full access to this article.
References
Awad, A., and Petrasovits, G. (1968). “Considerations on the bearing capacity of vertical and batter piles subjected to forces acting in different directions.” Proc., 3rd Conf. on Soil Mechanics and Foundation Engineering, Akademiai Kiado, 483–497.
Beringen, F. L., Windle, D., and Van Hooydonk, W. R. (1979). “Results of loading test on driven pile in sand.” Recent development in the design and construction of piles, ICE, London, 213–225.
Broms, B. B.(1966). “Methods of calculating the ultimate bearing capacity of piles.” Sols—Soil, 18-19, 21–32.
Broms, B. B., and Silberman, J. O.(1964). “Skin friction resistance for piles in cohensionless soils.” Sols—Soils, 10, 33–41.
Brucy, F., Meunier, J., and Nauzoy, J. (1991). “Behavior of pile plugs in sandy soils during and after driving.” Proc., 23rd Annual Offshore Technology, Houston, OTC 6514, 145–154.
Caquot, A., and Kerisel, J. (1948). Tables for the calculation of passive pressures, active pressures and bearing capacity on foundations, Gauthier-Villars, Paris.
Caquot, A., and Kerisel, J. (1949). Traite de mechanique des sols, Gauthier-Villars, Paris.
Coyle, H. M., and Castello, R. R.(1981). “New design correlations for piles in sand.” J. Geotech. Eng., 107(7), 965–986.
Coyle, H. M., and Sulaiman, I. H.(1967). “Skin friction for steel piles in sand.” J. Soil Mech. Found. Div., Am. Soc. Civ. Eng., 93(6), 261–278.
Gregerson, O. S., Aas, G., and Dibagio, E. (1973). “Load test on friction piles in loose sand.” Proc., 8th Int. Conf. on Soil Mechanics and Foundation Engineering, Moscowz, 109–117.
Hanna, A. M., and Afram, A.(1986). “Pull-out capacity of single batter piles in sand.” Can. Geotech. J., 23(3), 387–392.
Hanna, T. H., and Tan, R. H. S.(1973). “The behavior of long piles under compressive loads in sand.” Can. Geotech. J., 10, 311–340.
Kerisel, J. (1961). “Fondation profondes en milieux sableux: Variation de la Force Portant Limit en Fonction de la Densite, de la Profondeur, du Diametre et de la Vitesse d’ Enfoncement.” Proc., 5th Int. Conf. on Soil Mechanics and Foundation Engineering, Vol. 2, 73–83.
Lehane, B. M., Jardine, A. J., Bond, A. J., and Frank, R.(1993). “Mechanism of shaft friction in sand from instrumented pile tests.” J. Geotech. Eng., 119(1), 19–35.
Mansur, C. I., and Kaufman, R. I.(1956). “Pile tests, low-sill structure, Old River, Louisiana.” Trans. Am. Soc. Civ. Eng., 123, 715–743.
Meyerhof, G. G.(1976). “Bearing capacity and settlement of pile foundations.” J. Geotech. Eng., 102(3), 195–228.
Potyondy, J. G.(1961). “Skin friction between various soils and construction materials.” Geotechnique, 11(4), 339–353.
Poulos, H. G., and Davis, E. H. (1980). Pile foundation analysis and design, Wiley, New York.
Randolph, M. F., Dolwin, J., and Beck, R.(1994). “Driven piles in sand.” Geotechnique, 44(3), 427–448.
Ranjan, G. (1970). “The bearing capacity of batter piles under inclined loads in sand.” PhD thesis, Nova Scotia Technical College, Halifax, N.S., Canada.
Robinsky, E. I., and Morrison, C. E.(1964). “Sand displacement and compaction around model friction piles.” Can. Geotech. J., 1(2), 81–93.
Tavenas, F. A.(1971). “Load test results on friction piles in sand.” Can. Geotech. J., 8, 7–22.
Vesic, A. S. (1967). “A study of bearing capacity of deep foundations.” Final rep., Project B-189, Georgia Institute of Technology, Atlanta, Ga.
Vesic, A. S.(1970). “Tests on instrumented piles, Ogeechee River site.” J. Soil Mech. Found. Div., Am. Soc. Civ. Eng., 96(2), 561–504.
Vesic, A. S. (1977). “Design of pile foundation.” Synthesis of Highway Practice No. 42, Transportation Research Board, National Research Council, Washington, D.C.
Information & Authors
Information
Published In
Copyright
Copyright © 2003 American Society of Civil Engineers.
History
Received: Dec 11, 2001
Accepted: Aug 29, 2002
Published online: Jun 13, 2003
Published in print: Jul 2003
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.