Reliability of Axially Loaded Driven Pile Groups
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 127, Issue 12
Abstract
A method was presented to evaluate the reliability of axially loaded pile groups designed using the traditional concept of group efficiency along the lines of load and resistance factor design. Group effects and system effects were identified as the major causes that led to a significantly greater observed reliability of pile foundations than calculated reliability of single piles. Statistical analyses were conducted to evaluate these effects based on observed pile performance. A database of pile group load tests was collected and interpreted for this purpose. Subsequently, the reliability of pile groups associated with the allowable stress design practice was calculated using the suggested method. The calculated probability of failure of pile groups was found to be one to four orders of magnitude smaller than that of single piles, depending on the significance of group effects and system effects. Finally, values of the target reliability index βTS for single piles required to achieve a specified target reliability of pile group foundations were calculated for several design methods. Due to group effects and system effects, the values of βTS should be different for single piles, a pile group, and a pile system of several groups.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
AASHTO. ( 1999). LRFD bridge design specifications. Washington, D.C.
2.
Aggarwal, R. K., Litton, R. W., Cornell, C. A., Tang, W. H., Chen, J. H., and Murff, J. D. ( 1996). “Development of pile foundation bias factors using observed behavior of platforms during Hurricane Andrew.” Proc., 28th Annu. Offshore Technol. Conf., Vol. 2, Houston, TX, 445–455.
3.
American Petroleum Institute (API). ( 1993). “Recommended practice for planning, design and constructing fixed offshore platforms—Load and resistance factor design.” API RP 2A-LRFD.
4.
Ang, A. H.-S., and Tang, W. H. ( 1975). Probability concepts in engineering planning and design. I: Basic principles, Wiley, New York.
5.
Ang, A. H.-S., and Tang, W. H. ( 1984). Probability concepts in engineering planning and design. II: Decision, risk, and reliability, Wiley, New York.
6.
Barker, R. M., Duncan, J. M., Rojiani, K. B., Ooi, P. S. K., Tan, C. K., and Kim, S. G. ( 1991). “Load factor design criteria for highway structure foundations.” Final Rep., NCHRP Proj. 24-4, Virginia Polytechnic Institute and State University, Blacksburg, Va.
7.
Bea, R. G. ( 1983). “Characterization of the reliability of offshore piles subjected to axial loadings.” Proc., ASCE Struct. Congr., New York.
8.
Bea, R. G., Jin, Z., Valle, C., and Ramos, R. (1999). “Evaluation of reliability of platform pile foundations.”J. Geotech. and Geoenvir. Engrg., ASCE, 125(8), 696–704.
9.
Becker, D. E. ( 1996). “Eighteenth Canadian geotechnical colloquium: Limit states design for foundations. Part II. Development for the national building code of Canada.” Can. Geotech. J., 33(6), 984–1007.
10.
Brand, E. W., Muktabhant, C., and Taechathummarak, A. ( 1972). “Load tests on small foundations in soft clays.” Proc., Perf. of Earth and Earth-Supported Struct., Vol. 1, Part 2, ASCE, New York, 903–928.
11.
Burland, J. B. ( 1973). “Shaft friction piles in clay—A simple fundamental approach.” Ground Engrg., 6(3), 30–42.
12.
De Mello, V. F. B. ( 1969). “Foundation of buildings on clay.” Proc., 7th ICSMFE, Vol. 1, Mexico City, 49–136.
13.
Department of the Navy. ( 1982). “Foundations and earth structures design manual 7.2.” NAVFACDM-7.3, Alexandria, Va.
14.
Feld, J. ( 1965). Failures in foundation, Soiltest, Inc., Evanston, Ill.
15.
Focht, J. A. Jr., and O'Neill, M. W. ( 1985). “Piles and other deep foundations.” Proc., 11th ICSMFE, Balkema, Rotterdam, The Netherlands, 187–209.
16.
Gambino, S. J., and Gilbert, R. B. ( 1999). “Modeling spatial variability in pile capacity for reliability-based design.” Analysis, Design, Construction, and Testing of Deep Foundations, J. M. Roesset, ed., ASCE, Reston, 135–149.
17.
Gates, M. ( 1957). “Empirical formula for predicting pile bearing capacity.” Civ. Engrg., ASCE, 27(3), 65–66.
18.
Hannigan, P. J., Goble, G. G., Thendean, G., Likins, G. E., and Rausche, F. ( 1997). “Design and construction of driven pile foundations: Workshop manual.” Vol. 1, Publ. No. FHWA-HI-97-014. Federal Highway Administration, Washington, D.C.
19.
Kishida, H. ( 1967). “Ultimate bearing capacity of piles driven into loose sand.” Soils and Found., 7(3), 20–29.
20.
Kulhawy, F. H. ( 1996). “From Casagrande's `calculated risk' to reliability-based design in foundation engineering.” J. Boston Soc. of Civ. Engrs., 11(2), 43–56.
21.
Lacasse, S., and Goulois, A. ( 1989). “Uncertainty in API parameters for predictions of axial capacity of driven piles in sand.” Proc., 21st Offshore Technol. Conf., Society of Petroleum Engineers, Richardson, Tex., 353–358.
22.
Lazaridis, A., and O'Neill, M. W. ( 1991). “Analysis of geometric mispositioning in a vertical pile group.” Geotech. Engrg. Conf., F. G. McLean, ed., ASCE, New York, 519–530.
23.
Leonards, G. A. (1982). “Investigation of failures.”J. Geotech. Engrg. Div., ASCE, 108(2), 185–246.
24.
Liu, J. L., Yuan, Z. L., and Zhang, K. P. ( 1985). “Cap-pile-soil interaction of bored pile foundations.” Proc., 11th ICSMFE, Balkema, Rotterdam, The Netherlands, Vol. 3, 1433–1436.
25.
McVay, M. C., Birgisson, B., Zhang, L. M., Perez, A., and Putcha, S. ( 2000). “Load and resistance factor design (LRFD) for driven piles using dynamic methods—A Florida perspective.” Geotech. Testing J., 23(1), 55–66.
26.
Meyerhof, G. G. ( 1970). “Safety factors in soil mechanics.” Can. Geotech. J., 7(4), 349–355.
27.
Meyerhof, G. G. (1976). “Bearing capacity and settlement of pile foundations.”J. Geotech. Engrg. Div., ASCE, 102(3), 195–228.
28.
Ministry of Transportation of Ontario. ( 1991). Ontario highway bridge design code (OHBDC), 3rd Ed., Downsview, Ontario, Canada.
29.
O'Neill, M. W. ( 1983). “Group action in offshore piles.” Geotechnical practice in offshore engineering, S. G. Wright, ed., ASCE, New York, 25–64.
30.
Orchant, C. J., Kulhawy, F. H., and Trautmann, C. H. ( 1988). “Reliability-based foundation design for transmission line structures. 2: Critical evaluation of in-situ test methods.” EL-5507 Final Rep., Electrical Power Institute, Palo Alto, Calif.
31.
Paikowsky, S. G., Regan, J. E., and McDonnell, J. J. ( 1994). “A simplified field method for capacity evaluation of driven piles.” Publ. No. FHWA-RD-94-042, Federal Highway Administration, McLean, Va.
32.
Paikowsky, S. G., and Stenersen, K. L. ( 2000). “The performance of the dynamic methods, their controlling parameters and deep foundation specifications.” Proc., 6th Int. Conf. on Application of Stress-Wave Theory to Piles, S. Niyama and J. Beim, eds., Balkema, Rotterdam, The Netherlands, 281–304.
33.
Poulos, H. G. ( 1997). “Analysis of pile groups with defect piles.” Proc., 14th ICSMFE, Balkema, Rotterdam, The Netherlands, 871–876.
34.
Rausche, F., Goble, G., and Likins, G. (1985). “Dynamic determination of pile capacity.”J. Geotech. Engrg., ASCE, 111(3), 367–383.
35.
Schmertmann, J. H. ( 1967). “Guidelines for use in the soils investigation and design of foundations for bridge structures in the State of Florida.” Res. Bull. 121 (RB-121), prepared for the FDOT by the University of Florida, Gainesville, Fla.
36.
Schmertmann, J. H. ( 1978). “Guidelines for cone penetration test, performance, and design.” Rep. No. FHWA-TS-78-209, Federal Highway Administration, Washington, D.C.
37.
Sidi, I. D. ( 1985). “Probabilistic prediction of friction pile capacities.” PhD thesis, University of Illinois at Urbana, Ill.
38.
Sowers, G. F., Martin, C. B., Wilson, L. L., and Fausold, M. ( 1961). “The bearing capacity of friction pile groups in homogeneous clay from model studies.” Proc., 5th ICSMFE, Paris, 155–159.
39.
Standards Australia. ( 1995). Piling-design and installation. 1 The Crescent, Homebush, NSW 2140, Australia.
40.
Tang, W. H. ( 1989). “Uncertainties in offshore axial pile capacity.” Foundation engineering, F. H Kulhawy, ed., ASCE, New York, 833–847.
41.
Tang, W. H., and Gilbert, R. B. ( 1993). “Case study of offshore pile system reliability.” Proc., 25th Offshore Technol. Conf., Society of Petroleum Engineers, Richardson, Tex., 677–686.
42.
Tang, W. H., Woodford, D. L., and Pelletier, J. H. ( 1990). “Performance reliability of offshore piles.” Proc., 22nd Offshore Technol. Conf., Society of Petroleum Engineers, Richardson, Tex., 299–307.
43.
Tomlinson, M. J. ( 1971). “Some effects of pile driving on skin friction.” Proc., Conf. on Behavior of Piles, Institution of Civil Engineers, London, 107–114.
44.
Vesic, A. S. ( 1977). “Design of pile foundations.” NCHRP Synthesis of Highway Practice 42, Transp. Res. Board, National Research Council, Washington, D.C.
45.
Vijayvergiya, V. N., and Focht, J. N. Jr. ( 1972). “A new way to predict capacity of piles in clay.” Proc., 4th Offshore Technol. Conf., Society of Petroleum Engineers, Richardson, Tex., 865–874.
46.
Whitaker, T. ( 1960). “Some experiments on model pile foundations in clay.” Proc., Symp. on Pile Found., Int. Assn. for Bridge and Structural Engrg., Stockholm, Sweden.
47.
Whitman, R. V. (1984). “Evaluating calculated risk in geotechnical engineering.”J. Geotech. Engrg., ASCE, 110(2), 143–188.
48.
Withiam, J. L., et al. ( 1997). “Load and resistance factor design (LRFD) for highway bridge substructures.” FHWA Rep. DTFH61-94-C-00098, Federal Highway Administration, Washington, D.C.
49.
Wolff, T. F. (1993). “Probabilistic assessment of pile interference.”J. Geotech. Engrg., ASCE, 119(3), 525–542.
50.
Wu, T. H., Tang, W. H., Sangrey, D. A., and Baecher, G. B. (1989). “Reliability of offshore foundations: State of the art.”J. Geotech. Engrg., ASCE, 115(2), 157–178.
51.
Yoon, G. L., and O'Neill, M. W. ( 1996). “Design model bias factors for driven piles from experiments at NGES-UH.” Uncertainty in the geologic environment: From theory to practice, C. D. Shackelford, P. P. Nelson, and M. J. S. Roth, eds., ASCE, New York, 759–773.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 127 • Issue 12 • December 2001
Pages: 1051 - 1060
History
Received: Jul 7, 2000
Published online: Dec 1, 2001
Published in print: Dec 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.