Modeling Lateral Soil-Pile Response Based on Soil-Pile Interaction
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 126, Issue 5
Abstract
Although most designers prefer the p-y curve method as compared to elastic continuum or finite-element analysis of laterally loaded pile behavior, the profession has reached a state where it is time that closer scrutiny be given to the traditional “Matlock-Reese” p-y curves used in the analysis. The traditional p-y curves were derived from a number of well-instrumented field tests that reflect a limited set of conditions. To consider these p-y curves as unique is questionable. As important as such curves have been to advancing the practice from elastic to nonlinear beam on elastic foundation analysis, such calibrated/verified p-y curves reflect the specific field test conditions (particularly the pile properties) encountered. As presented in this paper, there are additional influences such as pile bending stiffness, pile cross-sectional shape, pile-head fixity, and pile-head embedment that have an effect on the resulting p-y curves. It is argued that strain wedge (SW) model formulation can be used to characterize such effects. SW model analysis predicts the response of laterally loaded piles and has shown very good agreement with actual field tests in sand, clay, and layered soils. The advantage of the SW model is that it is capable of taking into account the effect of changes in soil and pile properties on the resulting p-y curves.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Ashour, M., Norris, G., and Pilling, P. (1998). “Lateral loading of a pile in layered soil using the strain wedge model.”J. Geotech. and Geoenvir. Engrg., ASCE, 124(4), 303–315.
2.
Ashour, M., Pilling, P., Norris, G., and Perez, H. (1996). “Development of strain wedge model program for pile group interference and pile cap contribution effects.” CCEER Rep. No. 96-4, Civ. Engrg. Dept., University of Nevada at Reno, Reno, Nev.
3.
Briaud, J. L., Smith, T., and Mayer, B. ( 1984). “Laterally loaded piles and the pressuremeter: Comparison of existing methods.” Laterally Loaded Deep Foundations, ASTM STP 835, ASTM, West Conshohocken, Pa., 97–111.
4.
Cox, W. R., Reese, L. C., and Grubbs, B. R. (1974). “Field testing of laterally loaded piles in sand.” Proc., 6th Annu. Offshore Technol. Conf., OTC 2079, Offshore Technology Conference, Houston, 459–472.
5.
Coyle, H. M., and Reese, L. C. (1966). “Load transfer for axially loaded piles in clay.”J. Soil Mech. and Found. Div., ASCE, 92(2), 1–26.
6.
Dunnavant, T. W., and O'Neill, M. W. (1989). “Experimental p-y model for submerged stiff clay.”J. Geotech. Engrg., ASCE, 115(1), 95–114.
7.
Gabr, M. A., Lunne, T., and Powell, J. J. (1994). “P-y analysis of laterally loaded piles in clay using DMT.”J. Geotech. Engrg., ASCE, 120(5), 816–837.
8.
Gazioglu, S. M., and O'Neill, M. W. ( 1984). “Evaluation of p-y relationships in cohesive soils.” Analysis and design of pile foundations, J. R. Meyer, ed., ASCE, New York, 192–213.
9.
Gowda, P. ( 1991). “Laterally loaded pile analysis for layered soil based on the strain wedge model,” MS thesis, University of Nevada at Reno, Reno, Nev.
10.
Long, J. H., and Reese, L. C. (1983). “An investigation of the behavior of vertical piles in cohesive soils subjected to repetitive lateral loads.” Geotech. Engrg. Rep. GR83-7, Geotech. Engrg. Ctr., Bureau of Engrg. Res., University of Texas at Austin, Austin, Tex.
11.
Matlock, H. (1970). “Correlations for design of laterally loaded piles in soft clay.” Proc., 2nd Annu. Offshore Technol. Conf., OTC 1204, Offshore Technology Conference, Houston, 577–607.
12.
Murchison, J. M., and O'Neill, M. W. ( 1984). “Evaluation of p-y relationships in cohesionless soils.” Analysis and design of pile foundations, J. R. Meyer, ed., ASCE, New York, 174–191.
13.
Norris, G. M. (1986). “Theoretically based BEF laterally loaded pile analysis.” Proc., 3rd Int. Conf. on Numerical Methods in Offshore Piling,TECHNIP, Paris, 361–386.
14.
Reese, L. C. (1958). “Discussion of `Soil modulus for laterally loaded piles,' by Bramlette McClelland and John A. Focht, Jr.” Trans. ASCE, 123, 1071.
15.
Reese, L. C. (1983). “Behavior of piles and pile groups under lateral load.” Rep. Prepared for U.S. Department of Transportation, Federal Highway Administration, Office of Research, Development, and Technology, Washington, D.C.
16.
Reese, L. C. ( 1987). “Documentation of the computer program LPILE1.” Ensoft Inc., Tex.
17.
Reese, L. C., Cox, W. R., and Koop, F. D. (1974). “Analysis of laterally loaded piles in sand.” Proc., 6th Annu. Offshore Technol. Conf., OTC 2080, Offshore Technology Conference, Houston, 473–483.
18.
Reese, L. C., and Welch, R. C. (1975). “Lateral loading of deep foundations in stiff clay.”J. Geotech. Engrg. Div., ASCE, 101(7), 633–649.
19.
Robertson, P. K., Davies, M. P., and Campanella, R. G. (1989). “Design of laterally loaded driven piles using the flat dilatometer.” Geotech. Testing J., 12(1), 30–39.
20.
Ruiz, S. E. (1986). “Uncertainty about p-y curves for piles in soft clays.”J. Geotech. Engrg., ASCE, 112(6), 594–607.
21.
Skempton, A. W. (1954). “The pore pressure coefficients a and b.” Géotechnique, London, 4, 148.
22.
Smith, T. D. ( 1983). “Pressuremeter design method for single piles subjected to static lateral load,” PhD dissertation, Civ. Engrg. Dept., Texas A&M University, College Station, Tex.
23.
Terzaghi, K. (1955). “Evaluation of coefficients of subgrade reaction.” Géotechnique, London, 5(4), 297–326.
24.
Vesic, A. (1961). “Bending of beams resting on isotropic elastic solid.”J. Engrg. Mech. Div., ASCE, 87(2), 35–53.
Information & Authors
Information
Published In
History
Received: Aug 26, 1998
Published online: May 1, 2000
Published in print: May 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.