Load-Displacement Prediction for Horizontally Loaded Vertical Plates
This article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 123, Issue 1
Abstract
The load-displacement behavior of horizontally loaded vertical anchor plates as reported in 128 published field and laboratory investigations has been studied. Laboratory and field results documented in the literature have been collected for shallow anchor plates with a variety of configurations and embedded in different types of sands. A pullout capacity factor and a geometry factor were established. These factors are dimensionless and incorporate all the parameters that significantly affect the behavior of horizontally loaded vertical anchor plates. Several attempts have been made to plot the collected data in a form such that a general trend can be observed. This data was incorporated in a generalized form to predict the ultimate horizontal pullout resistance of vertical anchor plates in terms of the influencing parameters. Another formula was proposed to calculate the displacement associated with the applied load level. The proposed expressions are of good benefit to the practice since they provide an easy approximate estimation for parameters of relative complex nature, e.g., the ultimate pullout resistance and the associated displacement. The accuracy of these expressions are within reasonable limits especially since they are based on laboratory and field results obtained from tests in a wide variety of sands and conducted by several investigators under a diversity of settings and conditions.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Akinmusuru, J. O.(1978). “Horizontally loaded vertical plate anchor in sand.”J. Geotech. Engrg. Div., ASCE, 104(2), 283–286.
2.
Daniel, D. E., and Olson, R. E.(1982). “Failure of an anchored bulkhead.”J. Geotech. Engrg. Div., ASCE, 108(10), 1318–1327.
3.
Das, B. M.(1975). “Pullout resistance of vertical anchors.”J. Geotech. Engrg. Div., ASCE, 101(1), 87–91.
4.
Das, B. M., and Seeley, G. R.(1975). “Load-displacement relationship for vertical anchor plates.”J. Geotech. Engrg. Div., ASCE, 101(7), 711–715.
5.
Dickin, E. A., and Leung, C. F.(1983). “Centrifugal model tests on vertical anchor plates.”J. Geotech. Engrg., ASCE, 109(12), 1503–1525.
6.
Dickin, E. A., and Leung, C. F.(1985). “Evaluation of design methods for vertical anchor plates.”J. Geotech. Engrg., ASCE, 111(4), 500–520.
7.
Hueckel, S. (1957). “Model tests on anchoring capacity of vertical and inclined plates.”Proc., 4th Int. Conf. on Soil Mech. and Found. Engrg., Butterworths Scientific Publications, London, England, Vol. 2, 203–206.
8.
Neely, W. J., Stuart, J. G., and Graham, J.(1973). “Failure loads of vertical anchor plates in sand.”J. Soil Mech. and Found. Div., ASCE, 99(9), 669–685.
9.
Smith, J. E. (1962). “Deadman anchorages in sand.”Tech. Rep. R 199, U.S. Naval Civil Engineering Laboratory, Washington, D.C.
10.
Sowers, G. B., and Sowers, G. F.(1973). “Failures of bulkhead and excavation bracing.”Civ. Engrg., ASCE, 37(1), 72–77.
11.
Terzaghi, K., and Peck, R. B. (1967). Soil mechanics in engineering practice. John Wiley and Sons, Inc., New York, N.Y.
12.
Tsinker, G. P.(1983). “Anchored sheet pile bulkheads: design practice.”J. Geotech. Engrg., ASCE, 109(8), 1021–1038.
Information & Authors
Information
Published In
Copyright
Copyright © 1997 American Society of Civil Engineers.
History
Published online: Jan 1, 1997
Published in print: Jan 1997
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.