Experimental Study on Prefabricated Concrete Bridge Girder-to-Girder Intermittent Bolted Connections System
Publication: Journal of Bridge Engineering
Volume 12, Issue 5
Abstract
This paper reports on a new bridge deck slab flange-to-flange connection system for precast deck bulb tee (DBT) girders. In prefabricated bridge system made of DBT girders, the concrete deck slab is cast with the prestressed girder in a controlled environment at the fabrication facility and then shipped to the bridge site. This system requires that the individual prefabricated girders be connected through their flanges to make it continuous for live load distribution. The objectives of this study are to develop an intermittent bolted connection for DBT bridge girders and to provide experimental data on the ultimate strength of the connection system. This includes identifying the crack formation and propagation, failure mode, and ultimate load carrying capacity. In this study, three different types of intermittent bolted connection were developed. Four actual-size bridge panels were fabricated and then tested to collapse. The effects of the size and the level of the fixity of the connecting steel plates, as well as the location of the wheel load were examined. The developed joint was considered successful if the experimental wheel load satisfied the requirements specified in North American bridge codes. It was concluded that location of the wheel load at the deck slab joint affected the ultimate load carrying capacity of the connections developed. Failure of the joint was observed to be due to either excessive deformation and yielding of the connecting steel plates or debonding of the embedded studs in concrete.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by a contribution from the Ministry of Transportation of Ontario. Opinions expressed in this paper are those of the writers and do not necessarily reflect the views and policies of the Ministry. This support is gratefully acknowledged.
References
AASHTO (1998). LRFD bridge design specifications, 2nd Ed., Washington, D.C.
Anderson, A. R. (1957). “How beam design affects prestressed concrete bridge costs.” Eng. News-Rec., 326–328.
Anderson, A. R. (1972). “Systems concepts for precast prestressed concrete bridge construction.” Special Rep. No. 132, Highway Research Board, Washington, D.C., 9–21.
Anderson, A. R. (1973). “Stretched-out AASHTO-PCI beams, Type III and IV, for longer-span highway bridges.” J. Prestressed Concr. Inst., 18(5), 32–49.
Applied Technology Council. (1981). Proc., Workshop on Design of Prefabricated Concrete Buildings for Earthquake Loads, ATC-8, Applied Technology Council, Berkeley, Calif.
Arockiasamy, M., Badve, A. P., Rao, B. V., and Reddy, D. V. (1991). “Fatigue strength of joints in a precast prestressed concrete double tee bridge.” PCI J., 36(1), 84–96.
Bakht, B., Mufti, A. A., and Sargent, D. D. (2001). “Assessment of stresses in welds of shear-connected concrete plank bridges.” Proc., 29th Annual Conf. of the Canadian Society for Civil Engineering, Victoria, British Columbia, Canada.
Canadian Standard Association (CSA). (2000). “Canadian highway bridge design code.” CAN/CSA-S6-00, CSA International, Toronto.
Geren, K. Y., and Tadros, M. K. (1994). “The NU precast prestressed concrete bridge I-girder series.” PCI J., 39(3), 26–39.
Hariatmadar, H. (1997). “Seismic response of connections in precast concrete double tees.” Ph.D. dissertation, McGill Univ., Quebec.
Hofheins, C. L., Reaveley, L. D., and Pantelides, C. P. (2002). “Behavior of welded plate connections in precast concrete panels under simulated seismic loads.” PCI J., 47(4), 122–133.
PCI Committee on Connection Details. (1995). “Addendum to design and typical details of connections for precast and prestressed concrete.” PCI J., 40(5), 46–57.
PCI Committee on Connection Details. (1998). “Standard precast connections.” PCI J., 43(4), 42–58.
Pincheira, J. A., Oliva, M. G., and Kusumo-Rahardjo, F. I. (1998). “Tests on double tee flange connectors subjected to monotonic and cyclic loading.” PCI J., 43(3), 82–96.
Shahaway, M. E. (1990). “Feasibility study of transversely prestressed double-T bridges.” PCI J., 35(5), 56–69.
Shahaway, M. E., and Issa, M. (1992). “Load testing of transversely prestressed double-T bridges.” PCI J., 37(2), 86–99.
Sprinkel, M. M. (1985). “Prefabricated bridge elements and systems.” NCHRP Synthesis 119, National Cooperative Highway Research Program, Transportation Research Record, Washington, D.C.
Yamane, T., Tadros, M. K., Badie, S. S., and Baishya, M. C. (1998). “Full depth precast, prestressed concrete bridge deck system.” PCI J., 43(3), 50–66.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jun 3, 2005
Accepted: Aug 25, 2006
Published online: Sep 1, 2007
Published in print: Sep 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.