Simplified Moment Redistribution of Hybrid HPS 485W Bridge Girders in Negative Bending
Publication: Journal of Bridge Engineering
Volume 12, Issue 4
Abstract
Simplified moment redistribution procedures based on shakedown have recently been approved by AASHTO LRFD Bridge Design Specifications (AASHTO 2004). These procedures are currently only applicable for homogeneous girders, and thus, the objective of this study is to evaluate whether these procedures can be further applied for hybrid HPS 485W girders. A parametric study is carried out using validated three-dimensional finite-element (FE) analyses to study the inelastic behavior of hybrid HPS 485W girders in negative bending for this purpose. The effective plastic moments obtained from the FE studies are compared with those from the proposed prediction equations, where good correlation is observed. A design example of a three-span slab-on-girder bridge with hybrid HPS 485W girders using both elastic design and the simplified moment redistribution procedures is also presented, where it is shown that the use of moment redistribution procedures results in a negative bending section that is 13% lighter than the corresponding elastic design.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (1973). Standard specifications for highway bridges, 11th Ed., Washington, D.C.
AASHTO. (1986). Guide specifications for alternate load factor design procedures for steel beam bridges using braced compact sections, Washington, D.C.
AASHTO. (1998). LRFD bridge design specifications, 2nd Ed. (with 2001 interims), Washington, D.C.
AASHTO. (2004). LRFD bridge design specifications, 3rd Ed., Washington, D.C.
AASHTO and American Welding Society (AWS). (1995). AWS bridge welding code, ANSI/AASHTO/AWS/, 5–95.
Adams, P. F., Lay, M. G., and Galambos, T. V. (1964). “Experiments on high strength steel members.” Fritz Engineering Laboratory Rep. No. 297.8., Lehigh Univ., Bethlehem, Pa.
Alpsten, G. A. (1972). “Variation in mechanical and cross-sectional properties of steel.” Int. Conf. on Planning Design of Tall Buildings, ASCE-IABSE Int. Conf. Preprints: Rep. Nos. 1b-9, 1–51, Lehigh Univ., Bethlehem, Pa.
Barth, K. E., Hartnagel, B. A., White, D. W., and Barker, M. G. (2004). “Recommended procedures for simplified inelastic design of steel I-girder bridges.” J. Bridge Eng. 9(3) 230–242.
Barth, K. E., and White, D. W. (1998). “Finite-element evaluations of pier moment-rotation characteristics in continuous-span steel I-girders.” Eng. Struct. 20(8), 761–778.
Barth, K. E., White, D. W., and Bobb, D. W. (2000). “Negative bending resistance of HPS 70W girders.” J. Constr. Steel Res., 53(1), 1–31.
Barth, K. E., White, D. W., Righman, J. E., and Yang, L. L. (2005). “Evaluation of web compactness limits for singly and doubly symmetric steel I-girders.” J. Constr. Steel Res., 61, 1411–1434.
Grubb, M. A., and Schmidt, R. E. (2004). Three-span continuous composite I-girder design example, NSBA, in press.
Hibbitt, Karlsson & Sorensen, Inc. (HKS). (2002). ABAQUS standard user’s manual, Version 6.3.
Holtz, N. M., and Kulak, G. L. (1973). “Web slenderness limits for compact beams.” Structural Engineering Rep. No. 51, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alta., Canada.
Righman, J. E., and Barth, K. E. (2005). “Rotation capacity requirements for continuous span steel bridge girders.” Proc., 2005 Structural Stability Research Council Annual Technical Session and Meeting, Montreal.
Schilling, C. G., and Morcos, S. S. (1988). “Moment-rotation test of steel girders with ultracompact flanges.” Project No. 188-Autostress Design of Highway Bridges, American Iron and Steel Institute, Washington, D.C.
White, D. W., and Barth, K. E. (1998). “Strength and ductility of compact-flange I-girders in negative bendings.” J. Constr. Steel Res., 45(3), 241–280.
White, D. W., Ramirez, J. A., and Barth, K. E. (1997). “Moment rotation relationship for unified autostress designs of continuous-span bridge beams and girders.” Final Rep., Joint Transportation Research Program, West Lafayette, Ind.
Yang, L. L. (2004). “Evaluation of moment redistribution for hybrid HPS 70W girders.” Master’s thesis, Dept. of Civil and Environmental Engineering, West Virginia Univ., Morgantown, W.Va.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Apr 15, 2005
Accepted: Nov 7, 2005
Published online: Jul 1, 2007
Published in print: Jul 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.