Slippage of Neoprene Bridge Bearings
Publication: Journal of Bridge Engineering
Volume 5, Issue 3
Abstract
Elastomeric bearing pads are more appropriate than mechanical bearings to support bridge loads for many reasons. Two of the most significant reasons are cost and maintenance. Failure modes for bearing pads include crushing, delamination, and slippage. The most notable of these failure modes is slippage or “walking” out of place. The writers' objective in this paper is to establish a methodology to determine why some neoprene bearings are slipping under bridge girders. The methods used to investigate this phenomenon are discussed. A general survey of state DOTs was performed. The results are presented to show how some states have remedied this problem. During the investigation period, numerous bridge engineers and researchers gave their opinions as to why bearings slip. These theories are presented. This investigation has discovered that bearing slippage occurs on a daily basis.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Arditzoglou, Y. J., Yura, J. A., and Haines, A. H. (1995). “Test methods for elastomeric bearings on bridges.” Res. Rep. 1304-2, Ctr. for Transp. Res., University of Texas at Austin, Austin, Tex.
2.
Bakirzis, E. A., and Lindley, P. B. (1970). “Slipping at contact surfaces of plain rubber pads in compression.” Civ. Engrg. and Public Works Rev., 65(764), 306–307.
3.
Chen, R., and Yura, J. A. (1995). “Wax build-up on the surfaces of natural rubber bridge bearings.” Res. Rep. 1304-4, Ctr. for Transp. Res., University of Texas at Austin, Austin, Tex.
4.
Design of neoprene bridge bearing pads. (1959). E. I. Du Pont de Nemours and Co., Wilmington, Del.
5.
English, B. A., Klingner, R. E., and Yura, J. A. (1994). “Elastomeric bearings: Background information and field study.” Res. Rep. 1304-1, Ctr. for Transp. Res., University of Texas at Austin, Austin, Tex.
6.
Hamzeh, O., Tassoulas, J. L., and Becker, E. B. (1995). “Analysis of elastomeric bridge bearings.” Res. Rep. 1304-5, Ctr. for Transp. Res., University of Texas at Austin, Austin, Tex.
7.
Iverson, J. K., and Pfeifer, D. W. (1985). “Bearing pads for precast concrete buildings.” PCI J., 30(5), 128–155.
8.
Muscarella, J. V., and Yura, J. A. (1995). “An experimental study of elastomeric bridge bearings with design recommendations.” Res. Rep. 1304-3, Ctr. for Transp. Res., University of Texas at Austin, Austin, Tex.
9.
Price, A. R. (1978). “Abnormal and eccentric forces on elastomeric bridge bearings.” TRRL Lab. Rep. 708, Department of the Environment, Crowthorne, U.K.
10.
Roeder, C. W., Stanton, J. F., and Taylor, A. W. (1987). “Performance of elastomeric bearings.” NCHRP Rep. 298, Transportation Research Board, National Research Council, Washington, D.C.
11.
Schrage, I. ( 1981). Anchoring of bearings by friction, Spec. Publ. SP-70, American Concrete Institute, Detroit, 197–213.
12.
Stanton, J. F., and Roeder, C. W. (1982). “Elastomeric bearings design, construction, and materials.” NCHRP Rep. 248, Transportation Research Board, National Research Council, Washington, D.C.
13.
Stanton, J. F., and Roeder, C. W. (1992). “Elastomeric bearings: An overview.” Concrete Int.: Des. and Constr., 14(1), 41–46.
Information & Authors
Information
Published In
History
Received: Dec 2, 1998
Published online: Aug 1, 2000
Published in print: Aug 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.