Endurance of Deck-to-Deck Connections in Transverse Hardwood Glulam Decks
Publication: Journal of Bridge Engineering
Volume 5, Issue 1
Abstract
Dowel and stiffener beam deck-to-deck connections transfer shear and moment between hardwood glued-laminated (glulam) transverse deck panels in longitudinal timber bridges. The connections resist relative deflections between the deck panels and aid in the prevention of reflexive cracking of the bituminous wearing surface at panel joints. Cyclic loading can reduce the stiffness of some types of deck-to-deck connections resulting in shortened service life. The performance of dowel and stiffener beam deck-to-deck connections for hardwood glulam transverse panel bridge decks was evaluated during cyclic laoding. Five tests were conducted with steel dowel connected deck panels, and five tests were conducted with glulam stiffener beam connected deck panels. Each connection was subjected to 1,000,000 load cycles. Degradation of connector stiffness with increasing number of load cycles was determined. Stiffener beam connections had better cyclic load response than the steel dowel connections. Steel dowel connections experienced approximately 20% degradation of stiffness after 1,000,000 load cycles. Most stiffener beam connections experienced little to no stiffness degradation after 1,000,000 load cycles; the smaller stiffener beam experienced 14% degradation after 1,000,000 load cycles. All connections remained within the limits of deflection criteria established in the 1994 AASHTO LRFD Bridge Design Specifications.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
AASHTO LRFD bridge design specifications. (1994). American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
2.
LaCross, V. D. ( 1997). “Fatigue of interconnected deck connections in hard wood glued-laminated bridge decks,” MS thesis, Pennsylvania State University, University Park, Pa.
3.
McCutcheon, W. J., and Tuomi, R. L. ( 1973). “Procedure for design of glued-laminated orthotropic bridge decks.” Res. Paper FPL 210, USDA Forest Service, Forest Products Laboratory, Madison, Wis.
4.
McCutcheon, W. J., and Tuomi, R. L. ( 1974). “Simplified design procedure for glued-laminated bridge decks.” Res. Paper FPL 233, USDA Forest Service, Forest Products Laboratory, Madison, Wis.
5.
NELMA. ( 1991). Northeastern Lumber Manufacturers Association, Fallmouth, Me.
6.
Ritter, M. A. ( 1992). “Timber bridges: Design, construction, inspection, and maintenance.” USDA Forest Service, Forest Products Laboratory, Madison, Wis.
7.
Sanders, W. W., Jr. Klaiber, F. W., and Wipf, T. J. ( 1985). “Load distribution in glued laminated longitudinal timber deck highway bridges.” Iowa State University, Engineering Research Institute, Ames, Iowa.
8.
“Standard specifications for hardwood glued laminated timber.” (1996). AITC 119-96, American Institute of Timber Construction (AITC), Vancouver, Wash.
9.
“Standard specifications for carbon structural steel.” (1997). A36/A36M-96, ASTM, West Conshohocken, Pa.
10.
Thomforde, D. G. ( 1996). “Lag screw and deck clip performance evaluation in hardwood glulam timber bridge decking connections,” MS thesis, Pennsylvania State University, University Park, Pa.
11.
Witmer, R. W., Jr. ( 1996). “Load distribution characteristics of hardwood glued-laminated timber bridges and bridge components,” PhD dissertation, Pennsylvania State University, University Park, Pa.
Information & Authors
Information
Published In
History
Received: Sep 18, 1997
Published online: Feb 1, 2000
Published in print: Feb 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.