Effect of Multilanes on Wheel Load Distribution in Steel Girder Bridges
Publication: Journal of Bridge Engineering
Volume 4, Issue 2
Abstract
This paper presents the results of a parametric study that investigated the effect of multilanes and continuity on wheel load distribution in steel girder bridges. Typical one- and two-span, two-, three-, and four-lane, straight, composite steel girder bridges were selected for this study. The major bridge parameters chosen for this study were the span length, girder spacing, one- versus two-spans, and the number of lanes. These parameters were varied within practical ranges to study their influence on the wheel load distribution factors. A total of 144 bridges were analyzed using the finite-element method. The computer program, SAP90, was used to model the concrete slab as quadrilateral shell elements and the steel girders as space frame members. Simple supports were used to model the boundary conditions. AASHTO HS20 design trucks were positioned in all lanes of the one- and two-span bridges to produce the maximum bending moments. The calculated finite-element wheel load distribution factors were compared with the AASHTO and the National Cooperative Highway Research Program (NCHRP) 12-26 formulas. The results of this parametric study agree with the newly developed NCHRP 12-26 formula and both were, in general, less than the empirical AASHTO formula (S/5.5) for longer span lengths [>15.25 m (50 ft)] and girder spacing >1.8 m (6 ft). This paper demonstrates that the multiple lane reduction factors are built into the newly developed distribution factors for steel girder bridges that were presented in the NCHRP 12-26 final report. It should be noted that AASHTO LRFD contains a similar expression that results in a value that is 50% of the value in the equations developed as a part of NCHRP 12-26. This is due to the fact that AASHTO LRFD consider the entire design truck instead of half-truck (wheel loads) as the case in the NCHRP 12-26 report and the AASHTO Standard Specifications for Highway Bridges. Therefore, this paper supports the use of the new distribution factors for steel girder bridges developed as a part of NCHRP 12-26 and consequently the distribution factors presented in the AASHTO LRFD Bridge Design Specifications.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Bakht, B., and Moses, F. (1988). “Lateral distribution factors for highway bridges.”J. Struct. Engrg., ASCE, 114(8), 1785–1803.
2.
LRFD bridge design specifications . (1994). AASHTO, Washington, D.C.
3.
Mabsout, M. E., Tarhini, K. M., Frederick, G. R., and Tayar, C. (1997). “Finite element analysis of steel girder highway bridges.”J. Bridge Engrg., ASCE, 2(3), 83–87.
4.
Newmark, N. M. (1948). “Design of I-beam bridges.”J. Struct. Div., ASCE, 74(1), 305–330.
5.
Sanders, W. W. ( 1984). “Distribution of wheel loads on highway bridges.” Nat. Cooperative Hwy. Res. Program Synthesis 111, Transportation Research Board, Washington, D.C.
6.
SAP90 User's Manual . (1992). Computers & Structures Inc., Berkeley, Calif.
7.
“Standard specifications for highway bridges.” (1996). 16th Ed., AASHTO, Washington, D.C.
8.
Tarhini, K. M., and Frederick, G. R. (1992). “Wheel load distribution in I-girder highway bridges.”J. Struct. Engrg., ASCE, 118(5), 1285–1294.
9.
Zokaie, T., Osterkamp, T. A., and Imbsen, R. A. ( 1991). “Distribution of wheel loads on highway bridges.” Rep. 12-26/1, Nat. Cooperative Hwy. Res. Program, Transportation Research Board, Washington, D.C.
Information & Authors
Information
Published In
History
Received: Dec 2, 1997
Published online: May 1, 1999
Published in print: May 1999
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.