Load Distribution and Impact Factors for I-Girder Bridges
This article has a reply.
VIEW THE REPLYPublication: Journal of Bridge Engineering
Volume 2, Issue 3
Abstract
This paper presents the procedure and results of field tests that were performed on two simply supported steel I-girder bridges to assess girder distribution and impact factors. The measurements were performed under normal truck traffic. Strain data were taken from bottom flanges of girders in the middle of a span. Additional strain data were obtained under passes of a control truck with known weight and configuration. A computerized data acquisition technique enabled selective recording of the significant blocks of the strain data under normal traffic. Strains were measured for two consecutive days on each bridge. Measured data consist of strain blocks from approximately 900 trucks. The strain records were filtered with a lowpass digital filter to remove the dynamic components and to obtain an equivalent static strain. The data were further processed to obtain statistical parameters (mean and standard deviation) of the girder distribution and impact factors. The results were compared with the values calculated according to American Association of State Highway and Transportation (AASHTO) methods. Measured girder distribution factors are lower than AASHTO values. Measured impact factors are well below AASHTO values.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Association of State Highway and Transportation Officials (AASHTO). (1992). Standard specifications for highway bridges. Washington, D.C.
2.
American Association of State Highway and Transportation Officials (AASHTO). (1994). LRFD bridge design specifications. Washington, D.C.
3.
Bakht, B.(1981). “Testing of the Manitou Bridge to determine its safe load carrying capacity.”Can. J. Civ. Engrg., 8, 218–229.
4.
Bakht, B., and Jaeger, L. G.(1990). “Bridge testing—a surprise every time.”J. Struct. Engrg., ASCE, 116(5), 1370–1383.
5.
Bakht, B., and Pinjarkar, S. G. (1989). “Dynamic testing of highway bridges—a review.”Transp. Res. Rec. 1223, Transp. Res. Board, Nat. Res. Council, Washington, D.C., 93–100.
6.
Billing, J. R.(1984). “Dynamic loading and testing of bridges in Ontario.”Can. J. Civ. Engrg., 11, 833–843.
7.
Cantieni, R. (1983). “Dynamic load tests on highway bridges in Switzerland—60 years of experience.”Rep. 211, Swiss Federal Lab. for Mat. Testing and Res. (EMPA), Dubendorf, Switzerland.
8.
Darlow, M. S., and Bettigole, N. H.(1989). “Instrumentation and testing of bridge rehabilitated with exodermic deck.”J. Struct. Engrg., ASCE, 115(10), 2461–2480.
9.
Dorton, R. A., Holowka, M., and King, J. P. C.(1977). “The Conestogo River Bridge—design and testing.”Can. J. Civ. Engrg., 4, 18–39.
10.
Ghosn, M., Moses, F., and Gogieski, J. (1986). “Evaluation of steel bridges using in-service testing.”Transp. Res. Rec. 1072, Transp. Res. Board, Nat. Res. Council, Washington, D.C., 71–78.
11.
Kim, S., Sokolik, A. F., and Nowak, A. S. (1996). “Measurement of truck load on bridges in the Detroit area.”Transp. Res. Rec. 1541, Transp. Res. Board, Nat. Res. Council, Washington, D.C., 58–63.
12.
Laman, J. A., and Nowak, A. S.(1996). “Fatigue-load models for girder bridges.”J. Struct. Engrg., ASCE, 122(7), 726–733.
13.
Nassif, H. H., and Nowak, A. S. (1995). “Dynamic load spectra for girder bridges.”Transp. Res. Rec. 1476, Transp. Res. Board, Nat. Res. Council, Washington, D.C., 69–83.
14.
Newmark, N. M.(1948). “Design of I-beam bridges.”Hwy. Bridge Floor Symp., J. of Struct. Div., ASCE, 24(2), 141–161.
15.
Paultre, P., Chaallal, O., and Proulx, J.(1992). “Bridge dynamics and dynamic amplification factors—a review of analytical and experimental findings.”Can. J. Civ. Engrg., 19, 260–278.
16.
Proakis, J. G., and Manolakis, D. G. (1992). Digital signal processing: principals, algorithms, and applications, 2nd Ed., Macmillan Inc., Greenwich, Conn.
17.
Sanders, W. W., and Elleby, H. A. (1970). “Distributions of wheel loads on highway bridges.”Nat. Cooperative Hwy. Res. Program Rep. 83, Transp. Res. Board, Washington, D.C.
18.
Stallings, J. M., and Yoo, C. H.(1993). “Tests and ratings of short-span steel bridges.”J. of Struct. Engrg., ASCE, 119(7), 2150–2168.
19.
Tilly, G. P. (1986). Dynamic behavior of concrete structures. Developments in Civil Engineering. Vol. 13, Elsevier Science Publishing Co. Inc., New York, N.Y.
20.
Welch, P. D. (1967). “The use of fast Fourier transform for the estimation of power spectra: a method based on time averaging over short, modified periodograms.”IEEE Trans. on Audio and Electroacoustics, AU-15(June), 70–73.
21.
Zokaie, T., Osterkamp, T. A., and Imbsen, R. A. (1991). “Distribution of wheel loads on highway bridges.”Nat. Cooperative Hwy. Res. Program Rep. 12-26/1, Transp. Res. Board, Washington, D.C.
Information & Authors
Information
Published In
Copyright
Copyright © 1997 American Society of Civil Engineers.
History
Published online: Aug 1, 1997
Published in print: Aug 1997
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.