Practical Approach to Designing Wood Roof Truss Assemblies
Publication: Practice Periodical on Structural Design and Construction
Volume 13, Issue 3
Abstract
The objective of this research was to use a three-dimensional (3D) analysis method to evaluate “system effects” in light-frame roof truss assemblies. The goal of this study was to develop an improved and practical design method for 3D roof truss assemblies used in residential construction. A truss plate manufacturer (TPM) design software was used to lay out assemblies and to design individual trusses. The TPM software used a conventional design procedure (CDP) by analyzing one truss at a time in two dimensions. A commercially available structural analysis program was utilized to model and analyze 3D truss assemblies as a system. This system design procedure (SDP) is being proposed as a tool to analyze and design 3D roof truss assemblies. Three truss assemblies, L shape, T shape, and a complex assembly, were analyzed. The structural responses including combined stress index (CSI), truss deflections, and reactions from both CDP and SDP were compared and the system effects were evaluated. From this investigation, it is concluded that there are three system effects observed by the SDP, but not accounted for by CDP. These are: reduced applied load effect, truss-to-truss support effect, and stiff truss effect. Based on this investigation, the maximum CSI for most trusses in all three assemblies reduced by 6–60% because of system effects. SDP can help to improve the design of truss assemblies by directly including system effects that are not accounted for by the CDP.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Forest and Paper Association (AF&PA). (2005). National design specification for wood construction, Washington, D.C.
American National Standards Institute (ANSI). (2002). National standard for metal plate connected wood truss construction, ANSI/TPI 1-2002, Truss Plate Institute, Madison, Wis.
APA—The Engineered Wood Association. (1997). Plywood design specification, Tacoma, Wash.
Cramer, S. M., Drozdek, J. M., and Wolfe, R. W. (2000). “Load sharing effects in light-frame wood-truss assemblies.” J. Struct. Eng., 126(12), 1388–1394.
Cramer, S. M., and Wolfe, R. W. (1989). “Load-distribution model for light-frame wood roof assemblies.” J. Struct. Eng., 115(10), 2603–2616.
Diaz, R. J., Jr., and Schiff, S. D. (1998). “Influence of out-of-plane wall stiffness on structural behavior of wood roof assemblies.” Struct. Eng. World Wide 1998, Elsevier Science Ltd., New York.
Gupta, R., Miller, T. H., and Dung, D. (2004).“Practical solution to wood truss assembly design problems.” Pract. Period. Struct. Des. Constr., 9(1), 54–60.
LaFave, K. D., and Itani, R. (1992). “Comprehensive load distribution model for wood truss assemblies.” Wood Fiber Sci., 24(1), 79–88.
Li, Z., Gupta, R., and Miller, T. H. (1998). “Practical approach to modeling of wood truss roof assemblies.” Pract. Period. Struct. Des. Constr., 3(3), 119–124.
Limkatanyoo, P. (2003). “System behavior of three dimensional wood truss assemblies.” MS thesis, Oregon State Univ., Corvallis, Ore.
Liu, W., and Bulleit, W. M. (1995). “Overload behavior of sheathed lumber systems.” J. Struct. Eng., 121(7), 1110–1118.
McCutcheon, W. J. (1977). “Method for predicting the stiffness of wood-joist floor systems with partial composite action.” USDA-FS, Research Paper FPL 289, Forest Products Laboratory, Madison, Wis.
Meeks, J. E. (1999). “Thoughts on the future of the wood truss component industry.” Woodwords, September/October, 23–25.
Meeks, J. E. (2000). “Can technological advances help these wood truss problems?” Woodwords, June/July, 26–27.
National Association of Home Builders (NAHB). (2001). PATH technology roadmap: Whole house and building process redesign (Draft), Upper Marlboro, Md.
Rosowsky, D., and Ellingwood, B. (1991). “System reliability and load sharing effects in light frame wood construction.” J. Struct. Eng., 117(4), 1096–1114.
Wolfe, R. W., and McCarthy, M. (1989). “Structural performance of light-frame roof assemblies—I. Truss assemblies designed for high variability and wood failure.” Research Paper, FPL-RP-492, USDA, FOREST Products Laboratory, Madison, Wis.
Information & Authors
Information
Published In
Practice Periodical on Structural Design and Construction
Volume 13 • Issue 3 • August 2008
Pages: 135 - 146
Copyright
© 2008 ASCE.
History
Received: Aug 13, 2007
Accepted: Dec 10, 2007
Published online: Aug 1, 2008
Published in print: Aug 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.