Conceptual Structural Design in SEED
Publication: Journal of Architectural Engineering
Volume 1, Issue 4
Abstract
Although there are many computer-based tools for analyzing structures whose geometry, topology, and member properties have already been determined, there are very few general-purpose tools to assist structural designers in synthesizing structural configurations to be subsequently sized, analyzed, and detailed. The comceptual-structural-design submodule of the Software Environment to Support the Early Phases in Building Design (SEED-Config) is intended to fill this void. The process starts with a geometric model of the building's massing, a set of functional requirements to be satisfied, and a toolkit of technologies capable of generating potential structural system and subsystem alternatives. Structural alternatives can be rapidly generated under designer control to the level of detail desired and evaluated against a range of criteria. Provisions are made to store design cases as well as to retrieve and adapt these to meet new requirements.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Burkett, W. C., and Yang, Y.(1995). “The STEP integration information architecture.”Engineering with computers, 11(3), 136–144.
2.
Camacho, G. T. (1985). “LOW-RISE: An expert system for the structural planning and preliminary design of industrial-type buildings,” MS thesis, Carnegie Mellon University, at Pittsburgh, Pa.
3.
Fenves, S. J.(1971). “Scenario for a third computer revolution in structural engineering.”J. Struct. Div., ASCE, 97(1), 3–11.
4.
Fenves, S. J. (1986). “A framework for cooperative development of a finite modeling assistant.”Reliability of methods for engineering analysis, K. J. Bathe and D. R. J. Owen, eds., Pineridge Press, Swansea, U.K., 475–486.
5.
Fenves, S. J. (1995). “Successes and further challenges in computer-aided structural engineering.”Proc. 6th Int. Conf. on Comput. in Civ. and Bldg. Engrg., P. J. Pahl and H. Werner, eds., A. A. Balkema, Rotterdam, the Netherlands, 13–20.
6.
Fenves, S. J., Flemming, U., Hendrickson, C., Maher, M. L., Quadrel, R., Terk, M., and Woodbury, R. (1994). Concurrent computer-integrated building design . PTR Prentice-Hall, Inc., Englewood Cliffs, N.J.
7.
Flemming, U. (1994). “Case-based design in the SEED system.”Knowledge-based computer-aided architectural design, G. Carrara and Y. Kalay, eds., Elsevier, N.Y., 69–91.
8.
Flemming, U., and Woodbury, R.(1995). “Software environment to support early phases in building design (SEED).”J. Arch. Engrg., ASCE, 1(4), 147–152.
9.
Garrett, J. H. Jr., Kiliccote, H., and Choi, B.(1995). “Providing formal support for standards usage within SEED.”J. Arch. Engrg., ASCE, 1(4), 187–194.
10.
Ibarra-Anaya, E. G., and Fenves, S. J. (1991). “A framework for customizable knowledge-based systems with an application to a KBES for evaluating the seismic resistance of existing buildings.”Technical Report NCEER-91-0007, Nat. Ctr. for Earthquake Engrg. Res., State Univ. of New York, Buffalo, N.Y.
11.
Kolodner, J. L. (1993). Case-based reasoning . Morgan Kaufmann Publishers, Inc., San Mateo, Calif.
12.
Maher, M. L.(1988). “Engineering design synthesis: A domain independent representation.”Artificial Intelligence for Engrg. Design, 1(3), 207–213.
13.
Maher, M. L., and Fenves, S. J. (1985). “HI-RISE: An expert system for the preliminary structural design of high rise buildings.”Knowledge engineering in computer-aided design, J. S. Gero, ed., North-Holland Press, Amsterdam, Netherlands, 125–136.
14.
Meyer, S. (1995). “A description of the structural design of tall buildings through the grammar paradigm,” PhD thesis, Carnegie Mellon University, at Pittsburgh, Pa.
15.
Miller, E. M. (1990). “Implementing computer aided constructability critics,” MS thesis, Carnegie Mellon University, at Pittsburgh, Pa.
16.
Moore, C. V. (1995). “Computational decision support for preliminary bridge costing.”Proc. IABSE Colloquium on Knowledge Support Systems in Civ. Engrg. (IABSE Reports, Vol. 82), Int. Assoc. for Bridge and Struct. Engrs., Zurich, Switzerland, 3–12.
17.
Quadrel, R., Woodbury, R., and Fenves, S. J.(1993). “Controlling asynchronous team design environments with simulated annealing.”Res. in Engrg. Design, 5(2), 88–104.
18.
Sanvido, V. E., Fenves, S. J., and Wilson, J. L.(1992). “Aspects of virtual master builder.”J. Prof. Issues in Engrg., ASCE, 118(3), 261–278.
19.
Shiva, K., Suresh, H. S., Krishnamoorthy, C. S., Fenves, S. J., and Rajeev, S.(1994). “Gencrit: A tool for knowledge-based critiquing in engineering design.”Artificial Intelligence for Engrg. Design, Analysis and Manufacturing, 8(3), 239–259.
20.
Snyder, J., Aygen, Z., Flemming, U., and Tsai, J.(1995). “SPROUT—modeling language for SEED.”J. Arch. Engrg., ASCE, 1(4), 195–203.
21.
Sriram, D. (1987). Knowledge-based approaches to structural design . Computational Mechanics Publications, Southampton, U.K.
22.
Sriram, R. D., Logcher, R. D., Groleau, N., and Charoff, J. (1992). “DICE: An object-oriented programming environment for cooperative engineering design.”Artificial intelligence in engineering design, Vol. 3, Academic Press, New York, N.Y., 303–366.
23.
Wix, J., and Bloomfield, D. P. (1995). “Standardisation in the building industry: The STEP building construction core model.”Publication 180, Int. Council for Bldg. Res. Studies and Documentation, Stanford, Calif., 184–195.
24.
Woodbury, R., and Chang, T.-W.(1995). “Massing and enclosure design with SEED-Config.”J. Arch. Engrg., ASCE, 1(4), 170–178.
25.
Woodbury, R., and Fenves, S. J. (1994). “SEED-Config requirement analysis.”Internal SEED Document, Carnegie Mellon Univ., Pittsburgh, Pa.
26.
Zamanian, K. M. (1992). “Modeling and communicating spatial and functional information about constructed facilities,” PhD thesis, Carnegie Mellon University, at Pittsburgh, Pa.
Information & Authors
Information
Published In
Copyright
Copyright © 1995 American Society of Civil Engineers.
History
Published online: Dec 1, 1995
Published in print: Dec 1995
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.