Determination of Accurate Creep Compliance and Relaxation Modulus at a Single Temperature for Viscoelastic Solids
Publication: Journal of Materials in Civil Engineering
Volume 20, Issue 2
Abstract
Creep compliance (or relaxation modulus), which is a fundamental property that determines the strain (or stress) development in flexible pavements or damage evolution in asphalt mixtures, can be determined from either a creep compliance test using static loading or a complex modulus test using cyclic loading. Since the nature of each test is different, creep compliance determined from the complex modulus test was significantly different compared with that determined from the creep compliance test. From this rigorous experimental and analytical study, it was concluded that the creep compliance or complex modulus test alone is not capable of providing complete information over the typical time or frequency range used in single-temperature tests. In general, the complex modulus test provides accurate creep compliance at short loading time, while the creep compliance test provides accurate creep compliance at longer loading time. An approach to determine accurate creep compliance from the combination of creep and complex modulus tests at a single temperature was developed. The method provided accurate creep compliance values that corresponded to short-term and long-term experimental data.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to thank Howard Moseley and Shanna Johnson for their assistance in preparing specimens.
References
Buttlar, W. G., Roque, R., and Reid, B. (1998). “Automated procedure for generation of creep compliance master curve for asphalt mixtures.” Transportation Research Record. 1723, Transportation Research Board, Washington, D.C., 28–36.
Chehab, G. R., Kim, Y. R., Schapery, R. A., Witczak, M. W., and Bonaquist, R. (2002). “Time-temperature superposition principle for asphalt concrete with growing damage in tension state.” J. Assoc. Asph. Paving Technol., 71, 559–587.
Elseifi, M. A., Al-Qadi, I. L., and Yoo, P. J. (2006). “Viscoelastic modeling and field validation of flexible pavements.” J. Eng. Mech., 132(2), 172–178.
Ferry, J. D. (1980). Viscoelastic properties of polymer, 3rd Ed., Wiley, New York.
Findley, W. N., Lai, J. S., and Onaran, K. (1976). Creep and relaxation of nonlinear viscoelastic materials, Dover Publications, New York.
Hiltunen, D. R., and Roque, R. (1994). “A mechanics-based prediction model for thermal cracking of asphaltic concrete pavements.” J. Assoc. Asph. Paving Technol., 63, 81–117.
Huang, Y. H. (1993). Pavement analysis and design, Prentice-Hall, Englewood Cliffs, N.J.
Kim, J. (2005). “Accurate determination of dissipated creep strain energy and its effect on load- and temperature-induced cracking of asphalt pavement,” Ph.D. thesis, Univ. of Florida, Gainesville, Fla.
Kim, J., Roque, R., and Birgisson, B. (2005). “Obtaining creep compliance parameters accurately from static or cyclic creep tests.” ASTM STP 1469, ASTM, West Conshohocken, Pa., 177–197.
Lee, H. J., and Kim, Y. R. (1998). “Viscoelastic constitutive model for asphalt concrete under cyclic loading.” J. Eng. Mech., 124(1), 32–40.
Park, S. W., and Kim, Y. R. (2001). “Fitting prony-series viscoelastic models with power-law presmoothing.” J. Mater. Civ. Eng., 13(1), 26–32.
Pellinen, T., Witzak, M. W., and Bonaquist, R. (2002). “Asphalt mix master curve construction using sigmoidal fitting function with non-linear least squares optimization.” Proc., 15th Engrg. Mech. Conf., ASCE, Reston, Va., 83–101.
Roque, R., Birgisson, B., Drakos, C., and Dietrich, B. (2004). “Development and field evaluation of energy-based criteria for top-down cracking performance of hot mix asphalt.” J. Assoc. Asph. Paving Technol., 73, 229–260.
Roque, R., Buttlar, W. G., Ruth, B. E., Tia, M., Dickison, S. W., and Reid, B. (1997). “Evaluation of SHRP indirect tension tester to mitigate cracking in asphalt concrete pavements and overlays.” Final Rep. No. FDOT B-9885, Univ. of Florida, Gainesville, Fla.
Soules, T. F., Busbey, R. F., Rekhson, S. M., Markovasky, A., and Burke, M. A. (1987). “Finite-element calculation of stresses in glass parts undergoing viscous relaxation.” J. Am. Ceram. Soc., 70(2), 90–95.
Tschoegl, N. W. (1989). The phenomenological theory of linear viscoelastic behavior: An introduction, Springer, New York.
Wang, J., Birgisson, B., and Roque, R. (2006). “Effect of viscoelastic stress redistribution on the cracking performance of asphalt pavements.” J. Assoc. Asph. Paving Technol., 75, 637–675.
Zhang, Z., Roque, R., Birgisson, B., and Sangpetngam, B. (2001). “Identification and verification of a suitable crack growth law.” J. Assoc. Asph. Paving Technol., 70, 206–241.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Feb 5, 2007
Accepted: Jun 18, 2007
Published online: Feb 1, 2008
Published in print: Feb 2008
Notes
Note. Associate Editor: Eyad Masad
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.