Comparison of Unconfined‐ and Confined‐Creep Tests for Hot Mix Asphalt
Publication: Journal of Materials in Civil Engineering
Volume 6, Issue 2
Abstract
Both unconfined‐ and confined‐creep tests have been widely used to evaluate and characterize rutting potential in hot mix asphalt (HMA). However, no reference has been made suggesting that either the unconfined‐creep test or the confined‐creep test is better than the other. The unconfined and confined creep of a dense graded laboratory mix were measured at the conditions at which rutting is most likely to occur in HMA pavements. The relationship between sample air voids and the unconfined, as well as the confined, creep were evaluated in the laboratory and compared to the relationship between in‐place air voids and HMA rutting under traffic. In addition, the effect of mix preparation and specimen height on confined and unconfined creep were also evaluated. The creep test (unconfined‐or confined‐) that produced the test results most consistent to HMA rutting has the higher probability of evaluating the rutting performance of HMA, and is therefore recommended as the preferred method for conducting the creep test. The confined‐creep test was found to be more representative of in‐place performance.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Brown, E. R. (1990). “Density of asphalt concrete—how much is needed?” Transp. Res. Record 1282, Transp. Res. Board, Washington, D.C.
2.
Brown, E. R., and Bassett, C. E. (1990). “The effects of maximum aggregate size on rutting potential and other properties of asphalt‐aggregate mixtures.” Transp. Res. Record 1259, Transp. Res. Board, Washington D.C.
3.
Brown, E. R., and Cross, S. A. (1989). “A study of in‐place rutting of asphalt pavements.” Proc., Assoc. of Asphalt Paving Technologists, Vol. 58.
4.
Dawley, C. B., Hogewiede, B. L., and Anderson, K. O. (1989). “Mitigation of instability rutting of asphalt concrete pavements in Lethbridge, Alberta, Canada.” Proc., Assoc. of Asphalt Paving Technologists, Vol. 58.
5.
Finn, F. N., Monismith, C. L., and Markevich, N. J. (1983). “Pavement performance and asphalt concrete mix design.” Proc., Assoc. of Asphalt Paving Technologists, Vol. 52.
6.
Ford, M. C. (1988). “Pavement densification related to asphalt mix characteristics.” Proc., Annu. Meeting, Transp. Res. Board, Washington, D.C.
7.
Hadipour, K., and Anderson, K. O. (1988). “An evaluation of permanent deformation and low temperature characteristics of some recycled asphalt concrete mixtures.” Proc., Assoc. of Asphalt Paving Technologists, Vol. 57.
8.
Hopman, P. C., Maagdenberg, A. C., Coppens, M. H. M., and Dijkink, J. H. (1988). “Comparison of mechanical properties of drum mix and batch mix asphaltic concrete through dynamic testing.” Proc., Assoc. of Asphalt Paving Technologists, Vol. 57.
9.
Hudson, S. W., and Seeds, S. B. (1988). “Evaluation of increased pavement loading and tire pressure.” Proc., 67th Annu. Meeting, Transp. Res. Board, Washington, D.C.
10.
Kallas, B. F. (1966). “Asphalt pavement temperatures.” Hwy. Res. Record No. 150, Transp. Res. Board, Washington, D.C.
11.
Kenis, W. J. (1978). “Predictive design procedures, VESYS user's manual.” FHWA Rep. 77‐154, Federal Highway Administration, Washington, D.C.
12.
Kennedy, T. W., White, T. D., and Epps, J. A. (1983). “Use of material test and pavement design to evaluate new paving binders.” Properties of flexible pavement materials, ASTM STP 807, J. J. Emery, ed., ASTM, Philadelphia, Pa.
13.
Kronfuss, F., Krzemien, R., Nievelt, G., and Putz, P. (1984). “Verformungsfestigkjeit von asphalten emittlung im kriechtest,” Bundesministerium fur Bauten and Technik, Strassenforchung, Heft 240, Vienna, Austria, (in German).
14.
Lai, J. S., and Anderson, D. (1973). “Irrecoverable and recoverable nonlinear viscoelastic properties of asphalt concrete.” Transp. Res. Record 468, Transp. Res. Board, Washington, D.C.
15.
Middleton, D. R., Roberts, E. L., and Chira‐Chavala, T. (1986). “Measurement and analysis of truck tire pressures on Texas highways.” Transp. Res. Record 1070, Transp. Res. Board, Washington, D.C.
16.
Monismith, C. L., and Tayebali, A. A. (1988). “Permanent deformation (rutting) considerations in asphalt concrete pavement sections.” Proc., Assoc. of Asphalt Paving Technologists, Vol. 57.
17.
Parker, Frazier, and Brown, E. R. (1992). “Effects of aggregate properties on flexible pavement rutting in Alabama.” Effects of aggregate and mineral fillers on asphalt performance, ASTM STP 1147, Richard C. Meininger, ed., ASTM, Philadelphia, Pa.
18.
Perl, Mordechi, Uzan, Jacob, Sides, and Arieh. (1983). “Visco‐elasto‐plastic constitutive law for a bituminous mixture under repeated loading.” Transp. Res. Record 911, Transp. Res. Board, Washington, D.C.
19.
Rowe, G. M., and Cooper, K. E. (1988). “A practical approach to the evaluation of bituminous mix properties for the structural design of asphalt pavements.” Proc., Assoc. of Asphalt Paving Technologists, Vol. 57.
20.
van der Loo, P. J. (1976). “A practical approach to the prediction of rutting in asphalt pavements—the shell method.” Transp. Res. Record 616, Transp. Res. Board, Washington, D.C.
21.
Viljoen, A. W., and Meadows, K. (1981). “The creep test—a mix design tool to rank asphalt mixes in terms of their resistance to permanent deformation under heavy traffic.” Tech. Note: TP/36/81. Nat. Inst. for Transport and Road Res., Pretoria, South Africa.
22.
Yao, Z., and Monismith, C. L. (1986). “Behavior of asphalt mixtures with carbon black reinforcement.” Proc., Assoc. of Asphalt Paving Technologists, Vol. 55.
23.
Young, F. D., Deme, I., Burgess, R. A. and Kopvillem, O. (1969). “Ste. Anne test road‐construction and performance after two years of service.” Proc., Can. Tech. Asphalt Assoc, Vol. 14.
Information & Authors
Information
Published In
Copyright
Copyright © 1994 American Society of Civil Engineers.
History
Received: Aug 24, 1992
Published online: May 1, 1994
Published in print: May 1994
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.