Continuum Modeling and Discrete Element Simulations of Elastic-Quasi-Static Granular Flow in a Compressing Slot
Publication: Journal of Aerospace Engineering
Volume 22, Issue 4
Abstract
The stress generated by the horizontal compression of a vertical column of granular material is investigated. The column is open at the top so that the material is free to flow upward in the slot as it is compressed. This simple geometry has interesting mechanics because both elastic and frictional regimes coexist, and it is also relevant to problems involving the insulating material in cryogenic storage tanks. Two methods are used to investigate this problem: traditional continuum modeling and discrete element simulation. The continuum model assumes that the column consists of a frictional region near the top of the column and a linearly elastic region near the bottom. Analytic solutions are obtained for each region and predictions for the location of the transition are made based on intersections of the two solutions. A discrete element simulation of the same geometry is performed to compare with the results from the continuum model. Various conditions of wall friction and particle stiffness are simulated. Based on the outcome of this comparison, we verify that in a compressing slot there are essentially two distinct regions: a frictional flow region near the top of the column that results in an exponential increase in stress with depth. This eventually saturates leading to a linear-elastic plane strain region. The location of the transition between these two regions depends on the material properties and the state of the compression.
Get full access to this article
View all available purchase options and get full access to this article.
References
Babic, M., Shen, H. H., and Shen, H. T. (1990). “Stress tensor in granular shear flows of uniform, deformable disks at high solids concentrations.” J. Fluid Mech., 219, 81–118.
Bathurst, R. J., and Rothenburg, L. (1988). “Micromechanical aspects of isotropic granular assemblies with linear contact interactions.” ASME Trans. J. Appl. Mech., 55(1), 17–23.
Campbell, C. S. (2002). “Granular shear flows at the elastic limit.” J. Fluid Mech., 465, 261–291.
Chang, C. S., and Misra, A. (1990). “Packing structure and mechanical properties of granulates.” J. Eng. Mech., 116(5), 1077–1093.
Chang, C. S., Sundaram, S. S., and Misra, A. (1989). “Initial moduli of particulated mass with frictional contacts.” Int. J. Numer. Analyt. Meth. Geomech., 13(6), 629–644.
Chen, J., Rotter, J., and Ooi, J. (1999). “Review of numerical prediction methods for silo wall pressures.” Adv. Struct. Eng., 2(2), 119–134.
Issa, C. A., Peters, J. F., and Jones, E. W. (1995). “Structural effects of perlite compaction on cryogenic storage vessels subjected to thermal cycles and vibrations.” Int. J. Pressure Vessels Piping, 64, 51–65.
Janssen, H. A. (1895). “Versuche über Getreidedruck in Silozellen.” Z. Ver. Dtsch. Ing., 39(35), 1045–1049.
Ji, S., and Shen, H. H. (2006). “Effect of contact force models on granular flow dynamics.” J. Eng. Mech., 132(11), 1252–1259.
Lambe, T. W., and Whitman, R. V. 1979). Soil mechanics SI version, Wiley, New York.
Li, Y., Puri, V., and Manbeck, H. (1990). “Loads in a scaled, model bin subjected to cyclic ambient temperature.” Trans. ASAE, 33(2), 651–656.
Li, Y., Puri, V., and Manbeck, H. (1991). “Finite element model prediction of cyclic thermally induced loads in a scaled bin using elastic-viscoplastic constitutive equation.” Trans. ASAE, 34(5), 2207–2215.
Manbeck, H. B., and Puri, V. M. (1985). “Predicting thermally induced loads in thin-walled grain bins: State-of-the-art.” International Journal of Bulk Solids Storage in Silos, 1(3), 9–13.
Onoda, G. Y., and Liniger, E. G. (1990). “Random loose packings of uniform spheres and the dilatancy onset.” Phys. Rev. Lett., 64(22), 2727–2730.
Parmley, R. T., and Cunnington, G. R. (1974). “Evacuated load-bearing high-performance insulation study.” Final Report, May 1974–Aug. 1977, CR135342, Lockheed Missiles and Space Co., Palo Alto, Calif., Research Lab.
Puri, V. M., Zhang, Q., and Manbeck, H. B. (1986). “Influence of granular material properties on thermally induced bin loads.” Int. J. Bulk Solids Storage in Silos, 2(3), 1–7.
Tripodi, M., Puri, V., Manbeck, H., and Messing, G. (1994). “Triaxial testing of dry, cohesive powder and its application to a modified cam-clay constitutive model.” Powder Technol., 80(1), 35–43.
Zhang, Q., Puri, V., and Manbeck, H. (1989a). “Finite element predicted static and thermally induced loads in grain bins.” Trans. ASAE, 32(6), 2131–2136.
Zhang, Q., Puri, V., and Manbeck, H. (1989b). “Static and thermal loads in full size grain bins predicted by vectorized fem on supercomputer.” Trans. ASAE, 32(2), 685–690.
Zhang, Q., Puri, V. M., and Manbeck, H. B. (1988). “Model for frictional behavior of wheat on structural materials.” Trans. ASAE, 31(3), 898–903.
Zhang, Q., Puri, V. M., Manbeck, H. B., and Wang, M. C. (1987). “Finite element model for predicting static and thermally induced bin wall pressures.” Trans. ASAE, 30(6), 1797–1806.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Apr 30, 2008
Accepted: Dec 9, 2008
Published online: Sep 15, 2009
Published in print: Oct 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.