Quasi-Static Indentation Behavior of Honeycomb Sandwich Materials and Its Application in Impact Simulations
Publication: Journal of Aerospace Engineering
Volume 21, Issue 4
Abstract
Both the crushing and indentation behaviors of sandwich materials are important aspects in failure analysis and energy absorption. In this paper, the core crushing strength of honeycomb materials from the experiment is briefly introduced, and the indentation of sandwich structures is studied in detail. Using the beam on elastic-plastic foundation models, theoretical formulations for predicting indentation behavior of sandwich materials are proposed, from which the mechanical response of elastic-plastic sandwich beams are obtained. Three stages of failure are clearly depicted by the global stiffness changes in the load versus displacement curve of elastic-plastic beams. The models are compared with the available experimental data and numerical simulation, and relatively close agreements are achieved. The compliance and compliance gradient derived form the indentation models are then incorporated with the equation of motion of the projectile to study impact response of elastic-plastic beams, and the impact energy dissipation due to the plasticity of elastic-plastic sandwich beam is uniquely recovered from the derived damping ratio. The beam on elastic-plastic foundation models proposed can be used to predict the indentation behavior of honeycomb sandwich materials, and the unique incorporation of the compliance and compliance gradient of the elastic-plastic sandwich beams in the standard mass-spring model can be utilized to characterize the effect of core compression and plasticity in the impact process.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study is partially supported by the University of Akron and the Federal Highway Administration (FHWA)/Ohio Department of Transportation (ODOT) (State Job No. 134142).
References
Benson, A. S., and Mayers, J. (1967). “General instability and face wrinkling of sandwich plates—Unified theory and applications.” AIAA J., 5(4), 729–739.
Frostig, Y., and Baruch, M. (1990). “Bending of sandwich beams with transversely flexible core.” AIAA J., 28(3), 523–531.
Grenestedt, J. L., and Danielsson, M. (2005). “Elastic-plastic wrinkling of sandwich panels with layered cores.” J. Appl. Mech., 72(2), 276–281.
Hetenyi, M. (1961). Beams on elastic foundation, The University of Michigan Press, Ann Arbor, Mich.
Johnson, K. L. (1986). Contact mechanics, Cambridge University Press, Cambridge, U.K.
Mohr, D., and Doyoyo, M. (2003). “Nucleation and propagation of plastic collapse bands in aluminum honeycomb.” J. Appl. Phys., 94(4), 2262–2270.
Mohr, D., and Doyoyo, M. (2004). “Deformation-induced folding systems in thin-walled monolithic hexagonal metallic honeycomb.” Int. J. Solids Struct., 41(11–12), 3353–3377.
Qiao, P., Yang, M. J., and Mosallam, A. S. (2004). “Impact analysis of I-Lam sandwich system for over-height collision protection of highway bridges.” Eng. Struct., 26(7), 1003–1012.
Reissner, E. (1948). “Finite deflections of sandwich plates.” J. Aeronaut. Sci., 15(8), 435–440.
Schwarts-Givli, H., and Frostig, Y. (2000). “Behavior of unidirectional sandwich panels with a bi-linear soft core—Higher order approach.” ASME ICEME ’2000 Conf.
Shuaeib, F. M., and Soden, P. D. (1997). “Indentation failure of composite sandwich beams.” Compos. Sci. Technol., 57(9–10), 1249–1259.
Steeves, C. A., and Fleck, N. A. (2004). “Collapse mechanisms of sandwich beams with composite faces and a foam core, loaded in three-point bending. Part I: Analytical models and minimum weight design.” Int. J. Mech. Sci., 46(4), 561–583.
Yang, M. J. (2006). “Impact mechanics of elastic and elastic-plastic sandwich structures.” Ph.D. dissertation, Dept. of Civil Engineering, The Univ. of Akron, Akron, Ohio.
Yang, M. J., and Qiao, P. (2005a). “Nonlinear impact analysis of fully-backed composite sandwich structures.” Compos. Sci. Technol., 65(3–4), 551–562.
Yang, M. J., and Qiao, P. (2005b). “Higher-order impact modeling of sandwich beams with flexible core.” Int. J. Solids Struct., 42(20), 5460–5490.
Yang, M. J., and Qiao, P. (2008). “Compressive crushing behavior of aluminum honeycomb materials.” J. Sandwich Struct. Mater., 10(2), 133–160.
Zenkert, D., Shipsha, A., and Persson, K. (2004). “Static indentation and unloading response of sandwich beams.” Composites, Part B, 35(6–8), 511–522.
Zupan, M., Deshpande, V. S., and Fleck, N. A. (2004). “The out-of-plane-compressive behavior of woven-core sandwich plates.” Eur. J. Mech. A/Solids, 23(2), 411–421.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Dec 11, 2006
Accepted: Dec 19, 2007
Published online: Oct 1, 2008
Published in print: Oct 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.