Seismic Performance Evaluation of Nonseismic Designed Flat-Plate Structures
Publication: Journal of Performance of Constructed Facilities
Volume 22, Issue 6
Abstract
In this study the seismic performance of flat plate system structures designed without considering seismic load was investigated. Both the capacity spectrum method provided in ATC-40 in 1996 and nonlinear dynamic analyses were carried out to obtain maximum interstory drifts for earthquake loads. Also, a seismic performance evaluation procedure presented in FEMA-355F in 2000 was applied to evaluate the seismic safety of the model structures. The analysis results showed that the maximum interstory drifts of the nonseismic designed flat-plate structures computed by the capacity spectrum method and the nonlinear dynamic analysis were smaller than the limit state for the collapse prevention performance level. However, the results of the FEMA procedure showed that the model structures did not have enough strength to ensure seismic safety.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by Grant No. UNSPECIFIEDR0A–2006–000–10234-0 from the Basic Research Program of the Korea Science & Engineering Foundation. The writers appreciate this financial support.
References
American Concrete Institute (ACI). (2005). “Building code requirements for structural concrete (ACI 318–95) and commentary (318R-95).” ACI 318, Farmington Hill, Mich.
Applied Technology Council (ATC). (1996). “Seismic evaluation and retrofit of concrete buildings.” ATC 40, Redwood City, Calif.
Architectural Institute of Korea. (2005). Korean building code, Seoul, Korea.
Bai, J. W. (2003). “Seismic retrofit for reinforced concrete building structures.” Consequence-Based Engineering Institute Final Rep., Texas A&M Univ., College Station, Tex.
Binici, B., and Bayrak, O. (2003). “Punching shear strengthening of reinforced concrete flat plates using carbon fiber reinforced polymers.” J. Struct. Eng. 129(9), 1173–1182.
Cornell, C. A., Jalayer, F., Hamberger, R. O., and Foutch, D. A. (2002). “Probabilistic basis for SAC Federal Emergency Management Agency steel moment frame guidelines.” J. Struct. Eng., 128(4), 526–533.
Dilger, W. H. (2000). “Flat slab column connections.” Prog. Struct. Eng. Mater., 2(3), 386–399.
Erberik, M. A., and Elnashai, A. S. (2004). “Fragility analysis of flat-slab structures.” Eng. Struct., 26(7), 937–948.
Federal Emergency Management Agency (FEMA). (1997). “NEHRP guidelines for the seismic rehabilitation of buildings.” FEMA 273, Washington, D.C.
Federal Emergency Management Agency (FEMA). (2000a). “Prestandard and commentary for the seismic rehabilitation of buildings.” FEMA 356, Washington, D.C.
Federal Emergency Management Agency (FEMA). (2000b). “State of the art report on performance prediction and evaluation of steel moment-frame buildings.” FEMA 355F, Washington, D.C.
Hueste, M. B. D., and Bai, J. W. (2009a). “Seismic retrofit of a reinforced concrete flat-slab structure. Part I—Seismic performance evaluation.” Eng. Struct., in press.
Hueste, M. B. D., and Bai, J. W. (2009b). “Seismic retrofit of a reinforced concrete flat-slab structure. Part II—Seismic fragility analysis.” Eng. Struct., in press.
Hueste, M. B. D., and Wight, J. K. (1999). “Nonlinear punching shear failure model for interior slab-column connections.” J. Struct. Eng., 125(9), 997–1008.
Humay, F. K., and Durrani, A. J. (2001). “Experimental study of perforated infill panels for retrofitting flat plates.” ACI Struct. J., 98(5), 727–734.
International Code Council (ICC). (2006). International building code, Falls Church, Va.
Jalayer, F., and Cornell, C. A. (2003). “A technical framework for probability-based demand and capacity factor design (DCFD) seismic formats.” PEER Rep. No. 2003/8, Pacific Earthquake Engineering Center, Univ. of California at Berkeley, Berkeley, Calif.
Kang, TH. K., and Wallace, J. W. (2006). “Dynamic responses of flat plate systems with shear reinforcement.” ACI Struct. J., 102(5), 763–773.
Kim, T., and Kim, J. (2007). “Seismic performance evaluation of a RC special moment frame.” Struct. Eng. Mech., 27(6), 671–682.
Lee, K., and Foutch, D. A. (2002a). “Performance evaluation of new steel frame buildings for seismic loads.” Earthquake Eng. Struct. Dyn., 31(3), 653–670.
Lee, K., and Foutch, D. A. (2002b). “Seismic performance evaluation of pre-Northridge steel frame buildings with brittle connections.” J. Struct. Eng., 128(4), 546–555.
Luo, Y. H., and Durrani, A. J. (1995a). “Equivalent beam model for flat-slab buildings—Part I: Interior connections.” ACI Struct. J., 92(1), 115–124.
Luo, Y. H., and Durrani, A. J. (1995b). “Equivalent beam model for flat-slab buildings—Part II: Exterior connections.” ACI Struct. J., 92(2), 250–257.
Mander, J. B., Priestley, M. J. N., and Park, R. (1988). “Theoretical stress-strain model for confined concrete.” J. Struct. Eng., 113(8), 1804–1826.
Mazzoni, S., MacKenna, F., Scott, M. H., and Fenves, G. L. (2006). OpenSees command language manual, Pacific Earthquake Engineering Research Center, Berkeley, Calif., ⟨http://opensees.berkeley.edu⟩.
Moehle, J. P. (2000). “State of research on seismic retrofit of concrete building structures in the U.S.” U.S.–Japan Symp. and Workshop on Seismic Retrofit of Concrete Structures—State of Research and Practice, Japan Concrete Institute, Tokyo.
Murray, K. A., Cleland, D. J., Gilbert, S. G., and Scott, R. H. (2003). “Improved equivalent frame analysis method for flat plate structures in vicinity of edge columns.” ACI Struct. J., 100(4), 454–464.
Quisrani, A. N. (1993). “Interior post tensioned flat plate connections subjected to vertical and biaxial lateral loading.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of California at Berkeley, Berkeley, Calif.
Sherif, A. G., and Dilger, W. H. (1998). “Analysis and deflections of reinforced concrete flat slabs.” Can. J. Civ. Eng., 25(3), 451–466.
Somerville, P., Smith, N., Puntamurthual, S., and Sun, J. (1997). “Development of ground motion time histories for phase 2 of the FEMA/SAC steel project.” Background document, Rep. No. SAC/BD-97/04, SAC Joint Venture, Richmond, Calif.
Vamvatsikos, D., and Cornell, C. A. (2002). “Incremental dynamic analysis.” Earthquake Eng. Struct. Dyn., 31(3), 491–514.
Vanmarcke, E. H., and Gasparini, D. A. (1976). “A program for artificial motion generation: User’s manual and documentation.” Dept. of Civil Engineering, Massachusetts Institute of Technology, Cambridge, Mass.
Yun, S. Y., Hamburger, R. O., Cornell, C. A., and Foutch, D. A. (2002). “Seismic performance evaluation for steel moment frames.” J. Struct. Eng., 128(4), 534–545.
Zhang, W. J., Teng, J. G., Wong, Y. L., and Lu, Z. T. (2001). “Behavior of two way RC slabs externally bonded with steel plates.” J. Struct. Eng., 127(4), 390–397.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Dec 27, 2007
Accepted: Jun 6, 2008
Published online: Dec 1, 2008
Published in print: Dec 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.