Comparative Analysis of the Old MWHGL and the New NAPTF Data
Publication: Journal of Transportation Engineering
Volume 133, Issue 1
Abstract
The new generation of aircraft will require more landing-wheels to be packed into basically the same space. A convincing illustration of the move to more densely packed landing gears is the recent Boeing B777, which has six wheels on each of two tridem landing gears. This move increases concern that current pavement-design procedures do not accurately predict load interaction for the type of closely spaced landing gears on the new generation of aircraft. In response to the requirement for developing valid pavement-design procedures, the American Federal Aviation Administration constructed and conducted a National Airport Pavement Test Facility (NAPTF) with the cooperation of the Boeing Company. The data from the NAPTF tests recently made available gave an opportunity to run a comparative analysis with the old multiple-wheel, heavy-gear, load (MWHGL) data, which would contribute to the thickness-design issue in general, and to new large aircrafts in particular. The present paper describes this comparative analysis, which addresses only flexible pavements. Its main conclusions are as follows: (1) The present direct-regression interpretation of the full-scale trafficking tests indicates that the characteristics of the old MWHGL data are identical to those of the new NAPTF data, whereas the previous interpretation (i.e., the alpha-factor interpretation) suggests the opposite; further, the stability of the coefficients obtained in the regression analysis (i.e., the consistency of interpretations) can be regarded as significantly high. (2) All these findings may hint that the present direct-regression interpretation (which eliminates both the load-repetition factor and the need for equivalent single-wheel load calculations) can be considered a possible legitimate method, even one that is more appropriate from the engineering point of view. (3) The design equations based on the direct-regression equations lead to smaller values of total thicknesses than do those derived from the COMFAA program by up to 10% for very weak subgrades.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The results presented in this paper were obtained in the course of projects performed by the writers for various Israeli governmental agencies. Thanks are therefore due these agencies. The paper was prepared with the assistance of Mr. Arieh Aines, graphics editor, to whom thanks are also due.
References
Agrawal, S. K. (1998). “FAA’s national airport pavement test machine.” Proc., 3rd Int. Conf. on Road and Airfield Pavement Technology, Beijing.
Ahlvin, R. G., Ulery, H. H., Hutchinson, R. L., and Rice, J. L. (1971). “Multiple-wheel heavy gear load pavement tests; basic report.” Technical Rep. No. S-71-17, Vol. 1, U.S. Army Corps of Engineers, Waterways Experiment Station, Vicksburg, Miss.
Barker, W. R., and Gonzalez, C. R. (2005). “Renovation of the CBR design procedure.” Draft Rep., U.S. Air Force, U.S. Army Engineer Research and Development Center, Vicksburg, Miss.
Brill, D. R., and Hayoe, G. H. (2004). “Multiple-gear analysis for flexible pavement design in LEDFAA.” Proc., 2004 Federal Aviation Administration Airport Technology Transfer Conf., Atlantic City, N.J.
Divinsky, M., Ishai, I., and Livneh, M. (1996). “A simplified generalized CBR pavement design equation.” Transportation Research Record 1539, Transportation Research Board, Washington, D.C.
Divinsky, M., Ishai, I., and Livneh, M. (1998). “Probabilistic pavement design based on the generalized equation.” J. Transp. Eng., 124(6), 582–588.
Drenth, K. P. (2002). “Pavement design considerations regarding the introduction of the A380.” Proc., 2002 Federal Aviation Administration Airport Technology Transfer Conf., Atlantic City, N.J.
Federal Administration Aviation (FAA). (1995). “Airport pavement design and evaluation.” Advisory Circular 150/5320-6D, Office of Airport Safety and Standards, Washington, D.C.
Hammitt, G. M., and Hutchinson, R. L. (1971). “Multiple-wheel heavy gear load pavement tests.” Technical Rep. No. AFWL-TR-70-113, Vol. 4, U.S. Army Corps of Engineers, Waterways Experiment Station, Vicksburg, Miss.
Hayhoe, G. (2005). “Alpha factor determination for 6-wheel gears.” Federal Aviation Administration Airport Pavement Working Group Meeting, AAR-410, FAA William J. Hughes Technical Center, Atlantic City, N.J.
Hayhoe, G. F., Kawa, I., and Brill, D. R. (2004). “New developments in FAA airport pavement thickness design software.” Proc., Transportation Systems 2004 Workshop, Fort Lauderdale, Fla.
Kawa, I., and Hayhoe, G. F. (2002). “Development of a computer program to compute pavement thickness and strength.” Proc., 2002 Federal Aviation Administration Airport Technology Transfer Conf., Atlantic City, N.J.
Livneh, M. (2005). “Flexible pavement design for new large aircraft (NLA) based on the ACN equivalency concept.” Proc., Canadian Society of Civil Engineering (CSCE) 6h Transportation Specialty Conf., Toronto.
Livneh, M., and Divinsky, M. (1999). “New pavement design equation for the Boeing B-777 aircraft.” Proc., 1999 Federal Aviation Administration Airport Technology Transfer Conf., Atlantic City, N.J.
McQueen, R. D., Garg, N., and Ricalde, L. (2004). “Comparative analysis of airport pavement design procedures.” Proc., 2004 Federal Aviation Administration Airport Technology Transfer Conf., Atlantic City, N.J.
Taboza, P. A. (1977). “Procedures for the development of CBR design curves.” Instruction Rep. No. S-71-1, U.S. Army Corps of Engineers, Waterways Experiment Station, Vicksburg, Miss.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jun 3, 2005
Accepted: Oct 14, 2005
Published online: Jan 1, 2007
Published in print: Jan 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.