Analysis of Flexible Pavement Response and Performance Using Isotropic and Anisotropic Material Properties
Publication: Journal of Transportation Engineering
Volume 132, Issue 4
Abstract
Several research studies have shown that unbound pavement layers exhibit anisotropic properties. Anisotropy is caused by the preferred orientation of the aggregate, to which both the shape characteristics of the aggregate and the compaction force itself contribute. The result is that unbound pavement layers have higher stiffness in the vertical direction than in the horizontal direction. The efficacy of using anisotropic properties to represent unbound layers is demonstrated by comparing pavement surface deflection measurements under wheel loads to finite element predictions based on models that incorporate isotropic and anisotropic properties for the unbound base and subbase layers. The surface deflections in the flexible pavements of the AASHO road test were selected for this comparison because the AASHO road test is such a widely used database and because of the tight control of traffic, pavement cross sections, and material quality at the road test. The paper also analyzes the influence of characterizing pavement layers as isotropic and anisotropic on the predictions of fatigue and permanent deformation performance of flexible pavements using the recently developed National Cooperative Highway Research Program 1-37A models. The results show that the anisotropic behavior of pavement layers explains part of the shift and calibration factors used to relate laboratory measurements to field performance.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Association of State Highway Officials (AASHO). (1962a). “The AASHO road test.” Rep. 5, Pavement Research, Special Report 61E, Highway Research Board, Washington, D.C.
American Association of State Highway Officials (AASHO). (1962b). “The AASHO road test.” Rep. 7, Summary Rep., Special Report 61G, Highway Research Board, Washington, D.C.
Adu-Osei, A. (2000). “Characterization of unbound granular layers in flexible pavements.” Ph.D. dissertation, Dept. of Civil Engineering, Texas A&M Univ., College Station, Tex.
Adu-Osei, A., Little, D. N., and Lytton, R. L. (2001). “Cross-anisotropic characterization of unbound granular materials.” Transportation Research Record 1757, Transportation Research Board, Washington, D.C., 82–91.
ERES. (2002). “The 2002 design guide, design of new and rehabilitated pavement structures.” Draft Final Rep., National Cooperative Highway Research Program, Washington, D.C.
Finn, F., Saraf, C., Kulkarni, R., Nair, K., Smith, W., and Abdullah, A. (1977). “The use of distress prediction subsystems for the design of pavement structures.” 4th Int. Conf. on Structural Design of Asphalt Pavements, Univ. of Michigan, Ann Arbor, Mich.
Hicks, R. G., and Monismith, C. L. (1971). “Factors influencing the resilient properties of granular materials.” Transportation Research Record 345, Transportation Research Board, Washington, D.C., 15–31.
Kim, S. H. (2004). “Prediction of level of anisotropy of aggregates based on gradation, shape, form, and textural properties.” Ph.D. dissertation, Texas A&M Univ., College Station, Tex.
Little, D., Lytton, R., Williams, D., Chen, C. W., Kim, Y. R., and Lee, H. J. (1998). “Fundamental properties of asphalts and modified asphalts: Task K—Microdamage healing in asphalt and asphalt concrete.” Final Rep., Vol. I: Microdamage and MicrodamageHealing, Project Summary Rep., Federal Highway Administration, Washington, D.C.
Lytton, R. L., Uzan, J., Fernando, E. G., Roque, R., Hiltunen, D., and Stoffels, S. (1993). “Development and validation of performance prediction models and specifications for asphalt binders and paving mixes.” SHRP-A-357, Strategic Highway Research Program, National Research Council, Washington, D.C.
Masad, S. (2004). “Sensitivity of different flexible pavement analysis methods and AASHTO 2002 design guide to properties of unbound layers.” MSc thesis, Dept. of Civil Engineering, Texas A&M Univ., College Station, Tex.
May, R. W., and Witczak, M. W. (1981). “Effective granular modulus to model pavement responses.” Transportation Research Record 810, Transportation Research Board, Washington, D.C., 1–9.
Nishizawa, T., Shimeno, S., and Sekiguchi, M. (1997). “Fatigue analysis of asphalt pavements with thick asphalt mixture layer.” Proc., 8th Int. Conf. on Asphalt Pavements, 969–976.
Oh, J. H. (2004). “Field monitoring and modeling of pavement response and service life consumption due to overweight truck traffic.” Ph.D. dissertation, Dept. of Civil Engineering, Texas A&M Univ., College Station, Tex.
Tseng, K.-H., and Lytton, R. L. (1989). “Prediction of permanent deformation in flexible pavements materials.” Implication of aggregates in the design, construction, and performance of flexible pavements, STP 1016, H. G. Schreuders and C. R. Marek, eds., American Society of Testing and Materials, Philadelphia, 154–172.
Tutumluer, E. (1995). “Predicting behavior of flexible pavements with granular bases.” Ph.D. thesis, Georgia Institute of Technology, Atlanta, Ga.
Tutumluer, E. (1998). “Anisotropic behavior of unbound aggregate bases—State of the art summary.” Proc., 6th Annual Symp. of the Int. Center for Aggregate Research, St. Louis.
Tutumluer, E., Little, D., and Kim, S. H. (2004). “Validated model for predicting field performance of aggregate base courses.” Transportation Research Record 1837, Transportation Research Board, Washington, D.C., 41–49.
Uzan, J. (1985). “Characterization of granular materials.” Transportation Research Record 1022, Transportation Research Board, Washington, D.C., 52–59.
Wang, F., and Lytton, R. L. (1993). “System identification method for back calculating pavement layer properties.” Transportation Research Record 1384, Transportation Research Board, Washington, D.C., 1–7.
Information & Authors
Information
Published In
Journal of Transportation Engineering
Volume 132 • Issue 4 • April 2006
Pages: 342 - 349
Copyright
© 2006 ASCE.
History
Received: Apr 6, 2005
Accepted: Jul 14, 2005
Published online: Apr 1, 2006
Published in print: Apr 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.