Model for Three-Dimensional Highway Alignment
Publication: Journal of Transportation Engineering
Volume 132, Issue 12
Abstract
This research develops a model to solve for the three-dimensional alignment of a highway segment. Code requirements are taken into consideration, and mechanisms for maintaining heavy vehicle speeds are embedded in the model. The model brings the highway alignment close to certain preferred points, and avoids restricted areas when required. Horizontal alignment is composed of design elements, including tangent segments, circular curves, and clothoid curves. Vertical alignment is represented by lines and vertical curves. Both alignments are highly compatible with code requirements in practice. The three-dimensional alignment is obtained through an iterative process. With each iteration, a new horizontal alignment was obtained through a slight adjustment of the current alignment. Subsequently, a corresponding vertical alignment was developed by solving a series of linear mixed integer optimization problems. The entire solution process was divided into three stages with different tasks, and the accuracies in each stage carefully set to achieve efficiency. Some computational examples are provided.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2001). “A policy on geometric design of highways and streets.” Washington, D.C.
Bester, C. J. (2000). “Truck speed profiles.” Transportation Research Record. 1701, Transportation Research Board, Washington, D.C., 111–115.
Chew, E. P., Goh, C. J., and Fwa, T. F. (1989). “Simultaneous optimization of horizontal and vertical alignments for highways.” Transp. Res., Part B: Methodol., 23, 315–329.
Deck, G., and Scheuer, T. (1990). “Threshold accepting: A general purpose optimization algorithm appearing superior to simulated annealing.” J. Comput. Phys., 90, 161–175.
Easa, S. M. (1988). “Selection of roadway grades that minimize earthwork cost using linear programming.” Transp. Res., Part A, 22, 21–136.
Easa, S. M., Strauss, T. R., Hassan, Y., and Souleyrette, R. R. (2002). “Three-dimensional transportation analysis: Planning and design.” J. Transp. Eng., 128(3), 250–258.
Fwa, T. F. (1989). “Highway vertical alignment analysis by dynamic programming.” Highway Research Record. 1239, Transportation Research Board, Washington, D.C., 1–9.
Fwa, T. F., Chan, W. T., and Sim, Y. P. (2002). “Optimal vertical alignment analysis for highway design.” J. Transp. Eng., 128(5), 395–402.
Goh, C. J., Chew, E. P., and Fwa, T. F. (1988). “Discrete and continuous models for computation of optimal vertical highway alignment.” Transp. Res., Part B: Methodol., 22(6), 399–409.
Hassan, Y., Easa, S. M., and El Halim, A. (1997). “Design considerations for combined highway alignments.” J. Transp. Eng., 123(1), 60–68.
Hayman, R. W. (1970). “Optimization of vertical alignment for highways through mathematical programming.” Highway Research Record. 306, Transportation Research Board, Washington, D.C., 1–9.
Jha, M. K. (2003). “Criteria-based decision support system for selecting highway alignments.” J. Transp. Eng., 129(1), 33–41.
Jong, J. C. (1998). “Optimizing highway alignments with genetic algorithms.” Ph.D. dissertation, Dept. of Civil and Environ. Eng., Univ. of Maryland, College Park, Md.
Lee, Y., and Cheng, J. F. (2000). “Modeling the highway horizontal alignment design process.” J. Chin. Inst. Civ. Hydraul. Eng., 12, 327–340.
Lee, Y., and Cheng, J. F. (2001a). “A model for calculating optimal vertical alignments of interchanges.” Transp. Res., Part B: Methodol., 35, 1–23.
Lee, Y., and Cheng, J. F. (2001b). “Optimizing highway grades to minimize cost and maintain traffic speed.” J. Transp. Eng., 127(4), 303–310.
Lee, Y., and Shih, N. (1998). “A model for optimizing bridge and tunnel allocation in highway vertical alignment.” J. Chin. Inst. Civ. Hydraul. Eng., 10, 351–360.
Lee, Y., and Wu, Y. (1999). “Integrated model for optimal highway vertical alignment and climbing lane allocation.” J. Chin. Inst. Civ. Hydraul. Eng., 11, 529–542.
Moreb, A. A. (1996). “Linear programming model for finding optimal roadway grades that minimize earthwork cost.” Eur. J. Oper. Res., 93, 148–154.
Parker, N. A. (1977). “Rural highway route corridor selection.” Transp. Plan. Technol., 3, 247–256.
Smith, B. L., and Lamm, R. (1994). “Coordination of horizontal and vertical alignment with regard to highway esthetics.” Transportation Research Record. 1445, Transportation Research Board, Washington, D.C., 73–85.
Torbic, J. T., Harwood, D. W., Richard, K. R., and Glauz, W. D. (2004). “Determining critical length of grade for geometric design of vertical alignments.” Transportation Research Record. 1881, Transportation Research Board, Washington, D.C., 36–45.
Turner, A. K. (1978). “A decade of experience in computer aided route selection.” Photogramm. Eng. Remote Sens., 44, 1561–1576.
Turner, A. K., and Miles, R. D. (1971). “The GCARS system: A computer-assisted method of regional route location.” Highway Research Record. 348, Transportation Research Board, Washington, D.C., 1–15.
Wang, L. Z., Miura, K. T., Nakamae, E., Yamamoto, T., and Wang, T. J. (2001). “An approximation approach of the clothoid curve defined in the interval [0, PI/2] and its offset by free-form curves.” CAD, 33, 1049–1058.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Dec 22, 2004
Accepted: Apr 19, 2006
Published online: Dec 1, 2006
Published in print: Dec 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.