Design and Analysis System for Thermal Cracking in Asphalt Concrete
Publication: Journal of Transportation Engineering
Volume 126, Issue 4
Abstract
A reliability based mix design and analysis system for thermal cracking in asphalt concrete pavements is described and demonstrated in this paper. Asphalt-aggregate mixture performance in terms of low temperature cracking and thermal fatigue is assessed independently for each type of cracking in the specified environment. Reliability factors are introduced into this assessment to account for the level of risk assumed by the engineer and the inherent variability in the estimates of mixture resistance to induced thermal stresses and the environmental demand in terms of conditions promoting either type of thermal cracking. Mixture resistance is measured in two laboratory tests, and environmental demand is estimated from predicted surface pavement temperatures. The paper concludes with an example of the analysis described, comparing unmodified and crumb-rubber modified mixture performance at different levels of reliability in a high elevation desert climate. The system presented is recommended as a mix design and analysis tool for evaluating unmodified and modified asphalt-aggregate mixture performance in harsh climates where thermal cracking is of concern.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
AASHTO. ( 1995). AASHTO provisional standards, March edition, Washington, D.C.
2.
ASTM. ( 1996a). 1996 Annual book of ASTM standards, Vol. 04.04: Roofing, waterproofing, and bituminous materials, West Conshohocken, Pa.
3.
ASTM. ( 1996b). 1996 Annual book of ASTM standards, Vol. 04.03: Road and paving materials; Pavement management technologies, West Conshohocken, Pa.
4.
Christensen, D. (1998). “Analysis of creep data from indirect tension test on asphalt concrete.” J. Assn. of Asphalt Paving Technologists, 67, 458–492.
5.
Dempsey, B., Herlache, W., and Patel, A. ( 1985). Volume 3. Environmental effects on pavements—Theory manual, FHWA/RD-84/115, University of Illinois at Urbana-Champaign, Urbana, Ill.
6.
Epps, A. ( 1997). “Thermal behavior of crumb-rubber modified asphalt concrete mixtures.” UCB-ITS-DS-97-2, University of California, Berkeley, Berkeley, Calif.
7.
Epps, A. (1998). “A comparison of measured and predicted low temperature cracking conditions.” J. Assn. of Asphalt Paving Technologists, 67, 277–310.
8.
“Fatigue response of asphalt-aggregate mixes.” (1994). SHRP-A-404, Prepared for Strategic Highway Research Program, National Research Council, Washington, D.C., University of California, Berkeley, Institute of Transportation Studies, Asphalt Research Program, Berkeley, Calif.
9.
Finn, F., Saraf, C., Kulkarni, R., Nair, K., Smith, W., and Abdullah, A. (1977). “The use of distress prediction subsystems for the design of pavement structures.” Proc., 4th Int. Conf. on the Struct. Des. of Asphalt Pavements, Vol. I, Cushing-Malloy, Inc., Ann Arbor, Mich., 3–38.
10.
Harvey, J. ( 1991). Asphalt concrete specimen preparation protocol: SHRP asphalt project A-003A, version 3.0. TM-UCB-A-003A-91-2, University of California, Berkeley, Berkeley, Calif.
11.
Herlache, W., Patel, A., and Dempsey, B. ( 1985). The climatic-materials-structural pavement analysis program user's manual. FHWA/RD-86/085, University of Illinois at Urbana-Champaign, Urbana, Ill.
12.
Heukelom, W. (1966). “Observations on the rheology and fracture of bitumens and asphalt mixes.” Proc., Assn. of Asphalt Paving Technologists Tech. Sessions, Vol. 35, Cushing-Malloy, Inc., Ann Arbor, Mich., 358–399.
13.
Hicks, R. G., Lundy, J., Leahy, R., Hanson, D., and Epps, J. ( 1995). “Crumb rubber modifiers (CRM) in asphalt pavements: Summary of practices in Arizona, California, and Florida.” FHWA-SA-95-056, Federal Highway Administration, Washington, D.C.
14.
Hiltunen, D., and Roque, R. (1994). “A mechanics-based prediction model for thermal cracking of asphaltic concrete pavements.” J. Assn. of Asphalt Paving Technologists, 63, 81–113.
15.
Kanerva, H., Vinson, T., and Zeng, H. ( 1994). “Low-temperature cracking: Field validation of the thermal stress restrained specimen test.” SHRP-A-401, Strategic Highway Research Program, National Research Council, Washington, D.C.
16.
Lytton, R., and Shanmugham, U. (1982). “Analysis and design of pavements to resist thermal cracking using fracture mechanics.” Proc., 5th Int. Conf. on the Struct. Des. of Asphalt Pavements, Vol. I, Cushing-Malloy, Inc., Ann Arbor, Mich., 818–830.
17.
“Nevada standard specifications for road and bridge construction.” (1996). Section 703, Nevada Department of Transportation, Carson City, Nev.
18.
Performance graded asphalt binder specification and testing.” (1994). SP-1, Lexington, Ky.
19.
“Permanent deformation response of asphalt aggregate mixes.” (1994). SHRP-A-415, Prepared for Strategic Highway Research Program, National Research Council, Washington, D.C., University of California, Berkeley, Institute of Transportation Studies, Asphalt Research Program, Berkeley, Calif.
20.
Shahin, M., and McCullough, B. F. (1974). “Damage model for predicting temperature cracking in flexible pavements.” Transp. Res. Rec. 521, Transportation Research Board, Washington, D.C., 30–46.
21.
Summary of the day, manual. (1993). EarthInfo Inc., Boulder, Colo.
22.
Surface airways, manual. (1993). EarthInfo Inc., Boulder, Colo.
23.
Van der Poel, C. (1954). “A general system describing the visco-elastic properties of bitumen and its relation to routine test data.” J. Appl. Chem., 4, 221–236.
24.
Vinson, T., Janoo, V., and Haas, R. C. G. (1989). “Summary report on low temperature and thermal fatigue cracking.” SHRP-A/IR-90-001, Strategic Highway Research Program, National Research Council, Washington, D.C.
25.
Zubeck, H. K., and Vinson, T. (1996). “Prediction of low temperature cracking of asphalt concrete mixtures with thermal stress restrained specimen test results.” Transp. Res. Rec. 1545, Transportation Research Board, Washington, D.C., 50–58.
Information & Authors
Information
Published In
History
Received: Aug 6, 1998
Published online: Jul 1, 2000
Published in print: Jul 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.