Modeling of Residual Stresses in Structural Stainless Steel Sections
Publication: Journal of Structural Engineering
Volume 135, Issue 1
Abstract
The influence of residual stresses on structural members is to cause premature yielding and loss of stiffness, often leading to deterioration of load carrying capacity. Knowledge of their magnitude and distribution is therefore important for both structural design and finite-element simulations, and hence extensive studies have been performed on structural carbon steel components. With greater emphasis now being placed on durability and reducing consumption of resources, the use of stainless steel in construction is growing, heralding the need for a more precise understanding of its structural response. Stainless steel exhibits differing physical and thermal properties from carbon steel, both of which influence the formation of residual stresses, and it cannot simply be assumed that residual stress models for carbon steel are also appropriate for stainless steel. This paper examines all existing data on residual stresses in stainless steel sections, including data generated from a recent experimental program carried out at Imperial College, London and summarized herein. The collated residual stress data have been used to develop models for predicting the magnitude and distribution of residual stresses in press braked, cold rolled, hot rolled, and fabricated stainless steel structural sections.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to acknowledge the patience, hard work, and technical expertise of Ron Millward, Alfredo Olivo, Alan Roberts, and Trevor Stickland from the Structures Laboratory at Imperial College London, and would like to thank EPSRC and the Outokumpu Research Foundation for their financial and technical support.
References
Abdel-Rahman, N., and Sivakumaran, K. S. (1997). “Material properties models for analysis of cold-formed members.” J. Struct. Eng., 123(9), 1135–1143.
Bredenkamp, P. J., van den Berg, G. J., and van der Merwe, P. (1992). “Residual stresses and the strength of stainless steel I-section columns.” Proc., Structural Stability Research Council, Annual Technical Session, 69–86.
Brozzetti, G. A., Alpsten, G. A., and Tall, L. (1971). “Welding parameters, thick plates and column strength.” Welding J. Research Suppl., 50(8), 331–342.
BSK 99. (1999). “Boverkets handbok om stalkonstruktioner.” Boverket, Karlskrona, Sweden (in Swedish).
Centre for Advanced Structural Engineering. (1990). “Compression tests of stainless steel tubular columns.” Investigation Rep. No. S770, Univ. of Sydney, Sydney, Australia.
Chen, W. F., and Ross, D. A. (1977). “Tests of fabricated tubular columns.” J. Struct. Div., 103(3), 619–634.
Chernenko, D. E., and Kennedy, D. J. L. (1991). “An analysis of the performance of welded wide flange columns.” Can. J. Civ. Eng., 18(14), 537–554.
Clarin, M. (2003). “Measurement of longitudinal residual stresses in a cold formed rectangular hollow section.” Structural Design of Cold Worked Austenitic Stainless Steel, Internal Rep. No. 2003–08–30, Lulea Univ. of Technology, Lulea, Sweden.
Coetzee, J. S., van den Berg, G. J., and van der Merwe, P. (1990). “The effect of work hardening and residual stresses due to cold-work of forming on the strength of cold-formed stainless steel lipped channels.” Proc., 10th Int. Specialty Conf. on Cold-Formed Steel Structures, St. Louis, 143–162.
Cruise, R. B. (2007). “The influence of production routes on the behaviour of stainless steel structural members.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Imperial College, London.
Cruise, R. B., and Gardner, L. (2008). “Residual stress analysis of structural stainless steel sections.” J. Constr. Steel Res., 64(3), 352–366.
Dwight, J. B., and Mozham, K. E. (1969). “Welded steel plates in compression.” Struct. Eng., 47(2), 49–66.
Gardner, L. (2005). “The use of stainless steel in structures.” Prog. Struct. Eng. Mater., 7(2), 45–55.
Fukumoto, Y., and Itoh, Y. (1980). “Strength variation of laterally unsupported beams.” J. Struct. Div., 106(1), 165–181.
Fukumoto, Y., and Itoh, Y. (1981). “Statistical study of experiments on welded beams.” J. Struct. Div., 107(1), 89–103.
Huber, A. W., and Beedle, L. S. (1954). “Residual stress and compressive strength of steel.” Welding J. Research Suppl., 33(12), 589–614.
Ingvarsson, L. (1975). “Cold-forming residual stresses: Effect on buckling.” Proc., 3rd Speciality Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Mo., 85–119.
Ingvarsson, L. (1979). “Cold-forming residual stresses in thin-walled structures.” Proc., 1st Int. Conf. on Thin-Walled Structures, Univ. of Strathclyde, Glasgow, U.K., 575–587.
Kato, B., and Aoki, H. (1978). “Residual stresses in cold-formed tubes.” J. Strain Anal., 13(4), 193–204.
Key, P. W., and Hancock, G. J. (1993). “A theoretical investigation of the column behavior of cold-formed square hollow sections.” Thin-Walled Struct., 16(1–4), 31–62.
Lagerqvist, O., and Olsson, A. (2001). “Residual stresses in welded I-girders made of stainless steel and structural steel.” Proc., 9th Nordic Steel Construction Conf., 737–744.
Laubscher, R. F., and van der Merwe, P. (2003). “Structural design in hot rolled 3Cr12 sections.” Proc., Stainless Steel Structures Int. Experts’ Seminar, Ascot, U.K., Steel Construction Institute, 93–100.
Lay, M. G., and Ward, R. (1969). “Residual stresses in steel sections.” J. Austr. Inst. Steel Constr., 3(3), 2–21.
Madugula, M. K. S., Haidur, R., Monforton, G. R., and Marshall, D. G. (1997). “Additional residual stress and yield stress tests on hot-rolled angles.” Proc., Structural Stability Research Council Annual Technical Session, Toronto, 55–68.
Masubuchi, K. (1980). Analysis of welded structures, Pergamon, New York.
Nethercot, D. A. (1974). “Residual stresses and their influence upon the lateral buckling of rolled steel beams.” Struct. Eng., 3(52), 89–96.
Quach, W. M. (2005). “Residual stresses in cold formed steel sections and their effect on column behaviour.” Ph.D. thesis, Dept. of Civil and Structural Engineering, Hong Kong Polytechnic Univ., Hong Kong.
Quach, W. M., Teng, J. G., and Chung, K. F. (2004). “Residual stresses in steel sheets due to coiling and uncoiling: A closed form analytical solution.” Eng. Struct., 26(9), 1249–1259.
Quach, W. M., Teng, J. G., and Chung, K. F. (2006). “Finite element predictions of residual stresses in press-braked thin-walled steel sections.” Eng. Struct., 28(11), 1609–1619.
Schafer, B. W., and Peköz, T. (1998). “Computational modelling of cold-formed steel: Characterizing geometric imperfections and residual stresses.” J. Constr. Steel Res., 47(3), 192–210.
Wang, Y. D., Lin Peng, R., Wang, X. L., and McGreevy, R. L. (2002). “Grain-orientation-dependent residual stress and the effect of annealing in cold-rolled stainless steel.” Acta Mater., 50(7), 1717–1734.
Weisman, C., ed. (1976). “Fundamentals of welding.” American Welding Society welding handbook, Vol. 1, 7th Ed., Macmillan, New York.
Weng, C. C., and Peköz, T. (1990). “Residual stresses in cold formed sections.” J. Struct. Eng., 116(6), 1611–1625.
Weng, C. C., and White, R. N. (1990). “Residual stresses in cold-bent thick steel plates.” J. Struct. Eng., 116(1), 24–39.
Young, B., and Lui, W. M. (2005). “Behavior of cold-formed high strength stainless steel sections.” J. Struct. Eng., 131(11), 1738–1745.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Dec 22, 2006
Accepted: Jul 10, 2008
Published online: Jan 1, 2009
Published in print: Jan 2009
Notes
Note. Associate Editor: Benjamin N. Schafer
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.