Beam Finite-Element Analysis of Pressurized Fabric Tubes
Publication: Journal of Structural Engineering
Volume 133, Issue 7
Abstract
Lightweight, portable air-pressurized beams and arches serve as primary load-carrying members for a number of civilian and military structures. These members are made from synthetic fibers that are woven or braided into a circular cross section. The pressurized air provides structural capacity by pretensioning the fabric and through its behavior as a confined gas. In this paper, a beam finite element is developed for the analysis of pressurized fabric beams based on virtual work principles. Work done by internal pressure due to deformation-induced volume changes is included in the formulation. A nonlinear moment-curvature relationship accounts for fabric wrinkling, and shear deformations are incorporated. A mixed-interpolation Timoshenko beam element is used to discretize the virtual work expression. A numerical method for determining the moment-curvature relationship of an inflated beam made from a fabric obeying a nonlinear stress–strain relationship is developed. Results of experiments on pressurized fabric beams loaded in three- and four-point bending are presented, and the finite-element model is shown to accurately predict experimentally observed load-deflection response for a range of pressures. Simulations demonstrate that in addition to prestressing the fabric, the pressurized air significantly increases beam capacity as the beam volume decreases due to deformation.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research reported in this paper was conducted under Contract No. W911QY-05-C-0043 with the U.S. Army Natick Soldier Systems Center. The writers are grateful for this financial support.
References
Bouzidi, R., Ravaut, Y., and Wielgosz, C. (2003). “Finite elements for 2D problems of pressurized membranes.” Comput. Struct., 81, 2479–2490.
Cavallaro, P. V., Johnson, M. E., and Sadegh, A. M. (2003). “Mechanics of pressurized plain-woven fabric structures.” Compos. Struct., 61, 375–393.
Comer, R. L., and Levy, S. (1963). “Deflections of an inflated circular-cylindrical cantilever beam.” AIAA J., 1(7), 1652–1655.
Davids, W. G., and Turkiyyah, G. M. (1997). “Development of embedded bending member to model dowel action.” J. Struct. Eng., 123(10), 1312–1320.
Fichter, W. B. (1966). “A theory for inflated thin-wall cylindrical beams.” NASA Technical Note D-3466, Langley Research Center, Hampton, Va.
Friedman, Z., and Kosmatka, J. B. (1993). “An improved two-noded Timoshenko beam finite element.” Comput. Struct., 47(3), 473–481.
Gere, J. M., and Timoshenko, S. P. (1984). Mechanics of materials, 2nd Ed., PWS, Boston.
Hampel, J. W., Brown, G. J., and Sharpless, G. S. (1996). “High pressure inflatable structures incorporating highly oriented fibers.” Proc., 20th Army Scientific Conf.: Sci. and Technol. for Force XXI, Vol. II, Norfolk, Va., 953–957.
Kato, S., Yoshino, T., and Minami, H. (1999). “Formulation of constitutive equations for fabric membranes based on the concept of fabric lattice model.” Eng. Struct., 21, 691–708.
Le van, A., and Wielgosz, C. (2005). “Bending and buckling of inflatable beams: Some new theoretical results.” Thin-Walled Struct., 43, 1166–1187.
Main, J. A., Peterson, S., and Strauss, A. M. (1994). “Load-deflection behavior of space-based inflatable fabric beams.” J. Aerosp. Eng., 7(2), 225–238.
Main, J. A., Peterson, S., and Strauss, A. M. (1995). “Beam-type bending of space-based inflated membrane structures.” J. Aerosp. Eng., 8(2), 120–125.
MathWorks. (2002). Using MATLAB V. 6, MathWorks, Inc., Natick, Mass.
Molloy, S. J., Plaut, R. H., and Kim, J. (1999). “Behavior of pair of leaning arch-shells under snow and wind loads.” J. Eng. Mech., 125(6), 663–667.
Plaut, R. H., Goh, J. K. S., Kigudde, M., and Hammerand, D. C. (2000). “Shell analysis of an inflatable arch subjected to snow and wind loading.” Int. J. Solids Struct., 37(31), 4275–4288.
Quigley, C. J., Cavallaro, P. V., Johnson, A. R., and Sadegh, A. M. (2003). “Advances in fabric and structural analyses of pressure inflated structures.” Proc., IMECE’03 2003 ASME Int. Mechanical Engineering Congress, Washington, D.C., 19–25.
Steeves, E. C. (1975). “A linear analysis of the deformation of pressure stabilized beams.” Technical Rep. No. 75-47-AMEL, U.S. Army Natick Laboratories.
Steeves, E. C. (1978). “Pressure stabilized beam finite element.” Natick/TR-79/002, U.S. Army Natick Research and Development Command.
Thomas, J. C., and Wielgosz, C. (2004). “Deflections of highly inflated fabric tubes.” Thin-Walled Struct., 42, 1049–1066.
Webber, J. P. H. (1982). “Deflections of inflated cylindrical cantilever beams subjected to bending and torsion.” Aeronaut. J., 86(858), 306–312.
Wicker, W. J. (1992). “The structural characteristics of inflatable beams.” Acta Astronaut., 30, 443–454.
Wielgosz, C., and Thomas, J.-C. (2002). “Deflections of inflatable fabric panels at high pressure.” Thin-Walled Struct., 40, 523–536.
Wielgosz, C., and Thomas, J.-C. (2003). “An inflatable fabric beam finite element.” Commun. Numer. Methods Eng., 19, 307–312.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jun 20, 2006
Accepted: Oct 26, 2006
Published online: Jul 1, 2007
Published in print: Jul 2007
Notes
Note. Associate Editor: Keith D. Hjelmstad
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.