Experimental Evaluation of New Concrete Encased Steel Composite Beam to Steel Column Joint
Publication: Journal of Structural Engineering
Volume 133, Issue 4
Abstract
To reduce the floor-to-floor height, the technical, economical, and convenient (TEC) beam is developed as a new composite beam composed of structural tee, horizontal top stud, precast concrete, stirrup, and cast-in-place concrete slab. The preliminary testing of the proposed system was performed for simple beams, and the results indicated good structural behavior. However, application of the system in the relevant field requires the development of a moment-resisting connection using steel brackets on which upper rebars of the TEC beam are anchored. In this paper, three types of the proposed system are experimentally investigated under cyclic loadings. The parameters of the test are the spacing of transverse bars in the slab and the ratio of width of rebar spacing to bracket length. The structural behaviors such as load-displacement relation, ductility, variation of neutral axis, and failure pattern, were explored. Based on test results, specimens were classified as semirigid full strength by the Eurocode 4. It could be concluded that the proposed moment-resisting system shows good structural behavior and may be applicable in the field.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers deeply appreciate the contributions of the Daewoo Institute of Construction Technology, Dongyang Structural Engineers, and Haesung Kigong Co. Ltd.
References
AISC. (1994). Manual of steel construction, LRFD.
Architectural Institute of Korea (AIK). (1995). Code for design of reinforced concrete structure.
Bozzo, L. M., and Torres, L. (2004). “A proposed semi-prefabricated prestressed composite slab.” Proc. Inst. Civ. Eng., Struct. Build., 157(5), 309–317.
CEB-FIP. (1985). Model code for concrete structures, Comite Euro-International du Beton.
CEN. (1992a). “Design of steel structures—Part 1.1: General rules and rules for buildings.” Eurocode 3, NBN-ENV 1993-1-1, BIN.
CEN. (1992b). “Design of composite steel and concrete structures.” Eurocode 4, ENV 1994-1-1.
Daewoo Institute of Construction Technology (DICT). (2000). Technical document of TEC beam system (I), Daewoo E&C Ltd, Korea.
ECCS. (1995). Multi-story buildings in steel: Design guide for slim floors with built-in beams.
Johnson, R. P., and Anderson, D. (1993). Designer’s handbook to Eurocode 4—Part 1.1: Design of composite steel and concrete structures, Thomas Telford, London.
Ju, Y. K., Chun, S. C., and Yoon, S. W. (2005). “Assessment of composite column and RC beam joints.” Proc. Inst. Civ. Eng., Struct. Build., 158(3), 201–215.
Ju, Y. K., and Kim, S. D. (2005). “Structural behavior of alternative low floor height system using structural tee, half PC, and horizontal stud.” Can. J. Civ. Eng., 32, 329–338.
Ju, Y. K., Kim, J. Y., Kim, M. H., Chung, K. R., and Kim, S. D. (2002). “Structural assessment of RC column to TEC beam connection.” Arch. Inst. Korea Struct. J., 18(2), 45–52.
Kim, B. (1995). “A study on the ultimate capacity of inverted T-shape composite beam.” MS dissertation, Myongji Univ., Korea.
Kuang, J. S., and Wong, H. F. (2005). “Improving ductility of nonseismically designed RC columns.” Proc. Inst. Civ. Eng., Struct. Build., 158(1), 13–20.
Montesinos, G. P., and Wight, J. K. (2001). “Modeling shear behavior of hybrid RCS beam-column connections.” J. Struct. Eng., 127(1), 3–11.
MIDAS Information Technology (2000). MIDAS/gen on-line manual: General structural design system, Seoul.
Mullett, D. L. (1998). Composite floor systems, The Steel Construction Institute, Blackwell Science, U.K.
Naccarato, P. A. (2000). “Low floor-to-floor heights.” Modern steel construction.
Tagawa, Y. (1989). “Behavior of composite beams in steel frame under hysteretic loading.” J. Struct. Eng., 115(8), 2029–2045.
Viest, I. M., Colaco, J. P., Furlong, R. W., Griffis, L. G., Leon, R. T., and Wyllie, L. A. (1997). Composite construction design for buildings, McGraw-Hill, New York.
Zarate, A. V., and Mirambell, E. (2004). “Shear strength of tapered steel plate girders.” Proc. Inst. Civ. Eng., Struct. Build., 157(5), 343–354.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Dec 23, 2003
Accepted: Jun 22, 2006
Published online: Apr 1, 2007
Published in print: Apr 2007
Notes
Note. Associate Editor: Yan Xiao
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.