Behavior of Reinforced Concrete Column–Steel Beam Roof Level T-Connections under Displacement Reversals
Publication: Journal of Structural Engineering
Volume 132, Issue 7
Abstract
Results from an experimental study on the seismic response of two hybrid RC column-to-steel (S) beam (RCS) roof level T-connection subassemblies are presented. The primary variables investigated were: (1) anchorage requirements in column longitudinal bars; and (2) confinement requirements in RCS roof level T-connections. In the first subassembly the column bars were anchored by providing a development length of diameters and an end mechanical anchor with twice the diameter of the bar, while connection confinement was provided by steel band plates wrapping around the column regions just above and below the steel beam. This specimen exhibited a stable response up to 4.0% drift, the displacement at which a column bar anchorage failure occurred, which led to excessive bar slip through the connection with the associated decay in stiffness and strength. In the second specimen the development length for the column longitudinal bars was increased to diameters and a larger bearing area for the mechanical anchors was provided through steel channel sections running transversely above the top flange of the steel beam. The behavior of the second specimen was characterized by large column inelastic rotations, good stiffness retention and energy dissipation capacity, and limited joint damage. Thus, experimental results indicate that properly designed RCS roof level T-connections exhibit a stable behavior under large inelastic deformation reversals, such as those induced by strong earthquakes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research study described herein was sponsored by the National Science Foundation under Grant No. NSFCMS-0219503. The writers would also like to thank Mr. Robert Smith for support from ERICO, who supplied the headed bars used in this project. The suggestions of Professor James K. Wight are also greatly appreciated. The opinions expressed in this paper are those of the writers and do not necessarily reflect the views of the sponsor.
References
American Concrete Institute (ACI Committee 318). (2002). “Building code requirements for structural concrete.” Rep. ACI 318-02, Farmington Hills, Mich.
American Concrete Institute (ACI-ASCE Committee 352). (2002). “Recommendations for design of beam-column joints in monolithic reinforced concrete structures.” Rep. ACI 352-R-02, Farmington Hills, Mich.
AISC. (2002). “Seismic provisions for structural steel buildings.” Chicago.
American Society of Civil Engineers (ASCE Task Committee on Design Criteria for Composite Structures in Steel and Concrete). (1994). “Guidelines for design of joints between steel beams and reinforced concrete columns.” J. Struct. Eng., 120(8), 2330–2357.
Bugeja, M. N., Bracci, J. M., and Moore, W. P. (1999). “Seismic behavior of composite RCS frame systems.” Rep. CBDC-99-02, Dept. of Civil Engineering, Texas A&M Univ., College Station, Tex.
Chen, C. H., Cordova, P., Lai, W. C., Deierlein, G. G., and Tsai, K. C. (2004). “Pseudodynamic test of full-scale RCS frame. I: Design, construction and testing.” Proc., 13th World Conf. on Earthquake Engineering, Paper No. 2178, Vancouver, Canada.
Cordova, P., Lai, W. C., Chen, C. H., and Tsai, K. C. (2004). “Pseudodynamic test of full-scale RCS frame. II: Analyses and design implications.” Proc., 13th World Conf. on Earthquake Engineering, Paper No. 674, Vancouver, Canada.
Deierlein, G. G., Cordova, P., Tsai, K.-C., Chen, C.-H., and Lai, W.-C. (2005). “Composite moment frames.” Concr. Int., 27(5), 39–44.
Deierlein, G. G., Sheikh, T. M., Yura, J. A., and Jirsa, J. O. (1989). “Beam-column moment connections for composite frames. II.” J. Struct. Eng., 115(11), 2877–2896.
Griffis, L. (1986). “Some design considerations for composite-frame structures.” Eng. J., 23(2), 59–64.
Kanno, R. (1993). “Strength, deformation, and seismic resistance of joints between steel beams and reinforced concrete columns.” Ph.D. dissertation, Cornell Univ., Ithaca, N.Y.
Kanno, R., and Deierlein, G. G. (1996). “Seismic behavior of composite (RCS) beam-column joint subassemblies.” Composite Construction in Steel and Concrete III: Proc., Engineering Foundation Conf., Irsee, Germany, 236–249.
Liang, X., and Parra-Montesinos, G. (2004). “Seismic behavior of reinforced concrete column-steel beam subassemblies and frame systems.” J. Struct. Eng., 130(2), 310–319.
Mosalam, K. M., Naito, C., and Khaykina, S. (2002). “Bidirectional cyclic performance of reinforced concrete bridge column-superstructure subassemblies.” Earthquake Spectra, 18(4), 663–687.
Parra-Montesinos, G., Liang, X., and Wight, J. K. (2003). “Toward deformation-based capacity design of RCS beam-column connections.” Eng. Struct., 25(5), 681–690.
Parra-Montesinos, G., and Wight, J. K. (2000). “Seismic behavior, strength and retrofit of exterior RC column-to-steel beam connections.” Rep. UMCEE 00-09, Dept. of Civil and Environmental Engineering, Univ. of Michigan, Ann Arbor, Mich.
Parra-Montesinos, G., and Wight, J. K. (2001). “Modeling shear behavior of hybrid RCS beam-column connections.” ACI Struct. J., 98(5), 762–770.
Sheikh, T. M., Deierlein, G. G., Yura, J. A., and Jirsa, J. O. (1989). “Beam-column moment connections for composite frames. I.” J. Struct. Eng., 115(11), 2858–2876.
Sritharan, S., Werff, J. V., Abendroth, R. E., Wassef, W. G., and Greimann, L. F. (2005). “Seismic behavior of a concrete/steel integral bridge pier system.” J. Struct. Eng., 131(7), 1083–1094.
Wallace, J., McConnell, S., Gupta, P., and Cote, P. (1998). “Use of headed reinforcement in beam-column joints subjected to earthquake loads.” ACI Struct. J., 95(5), 590–606.
Yamanouchi, H., Nishiyama, I., and Kobayashi, J. (1998). “Development and usage of composite and hybrid building structure in Japan.” Special publication 174, American Concrete Institute, Farmington Hills, Mich., 151–173.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Jan 19, 2005
Accepted: Sep 14, 2005
Published online: Jul 1, 2006
Published in print: Jul 2006
Notes
Note. Associate Editor: Yahya C. Kurama
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.