Effects of Panel Zone Strength and Beam Web Connection Method on Seismic Performance of Reduced Beam Section Steel Moment Connections
Publication: Journal of Structural Engineering
Volume 131, Issue 12
Abstract
This paper presents test results on eight reduced beam section (RBS) steel moment connections. The testing program addressed web connection type (bolted versus welded) and panel zone (PZ) strength as the key variables. Specimens with medium PZ strength were designed to promote energy dissipation from both PZ and RBS regions such that expensive doubler plates were not needed. Both strong and medium PZ specimens with a welded web connection were able to provide satisfactory connection rotation capacity for special moment-resisting frames. However, specimens with a bolted web connection performed poorly due to premature brittle fracture of the beam flange at the weld access hole. A plausible explanation for the higher incidence of base metal fracture in bolted web specimens was presented based on the measured strain data. Test results from this study and by others showed that panel zones could easily develop a plastic rotation of without causing distress to the beam flange groove welds. At this deformation level, the amount of beam distortion (i.e., buckling) was about one half that developed in strong PZ specimens. A criterion for a balanced PZ strength that improves the plastic rotation capacity while reducing the amount of beam buckling is proposed.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgment
Financial support to the first writer provided by the Research Institute of Industrial Science and Technology in Korea and the Korea Earthquake Engineering Research Center is gratefully acknowledged.
References
American Institute of Steel Construction (AISC). (1997 and 2002). Seismic provisions for structural steel buildings, American Institute of Steel Construction, Chicago.
Chen, S. J., Yeh, C. H., and Chu, J. M. (1996). “Ductile steel beam-to-column connections for seismic resistance.” J. Struct. Eng., 122(11), 1292–1299.
Chi, B., and Uang, C.-M. (2002). “Cyclic response and design recommendations of reduced beam section moment connections with deep columns.” J. Struct. Eng., 128(4), 464–473.
Choi, J. H., Stojadinovic, B., and Goel, S. C. (2000). “Development of free flange moment connection.” Technical Rep. No. UMCEE 00-15, Dept. of Civil and Environmental Engineering, Univ. of Michigan, Ann Arbor, Mich.
El-Tawil, S. (2000). “Panel zone yielding in steel moment connections.” Eng. J., 37(3), 120–131.
Engelhardt, M. D., Venti, M. J., Fry, G. T., Jones, S. L., and Holliday, S. D. (2000). “Behavior and design of radius cut reduced beam section connections.” SAC/BD-00/17, SAC Joint Venture, Sacramento, Calif.
Engelhardt, M. D., Winneberger, T., Zekany, A. J., and Potyraj, T. J. (1998). “Experimental investigations of dogbone moment connections.” Eng. J., 35(4), 128–139.
Iwankiw, N. (1997). “Ultimate strength consideration for seismic design of the reduced beam section (internal plastic hinge).” Eng. J., 34(1), 3–16.
Jones, S. L., Fry, G. T., and Engelhardt, M. D. (2002). “Experimental evaluation of cyclically loaded reduced beam section moment connections.” J. Struct. Eng., 128(4), 441–451.
Kawano, A. (1984). “Inelastic behavior of low-rise frame based on a weak beam-to-column connection philosophy to earthquake motion.” Proc., 8th World Conf. on Earthquake Engineering, Vol. IV, San Francisco, 519–526.
Krawinkler, H. (1978). “Shear in beam-column joints in seismic design of steel frames.” Eng. J., 15(3), 82–91.
Krawinkler, H., Gupta, A., Medina, R., and Ruco, N. (2000). “Loading histories for seismic performance testing of SMRF components and assemblies.” Rep. No. SAC/BD-00/10, SAC Joint Venture, Sacramento, Calif.
Krawinkler, H., and Popov, E. P. (1982). “Seismic behavior of moment connections and joints.” J. Struct. Div. ASCE, 108(2), 373–391.
Plumier, A. (1997). “The dogbone: Back to the future.” Eng. J., 34(2), 61–67.
Ricles, J. M., Mao, C., Lu, L. W., and Fisher, J. W. (2002). “Inelastic cyclic testing of welded unreinforced moment connections.” J. Struct. Eng., 128(4), 429–440.
Roeder, C. W. (2002). “General issues influencing connection performance.” J. Struct. Eng., 128(4), 420–428.
SAC (2000). “Seismic design criteria for new moment-resisting steel frame construction.” Rep. No. FEMA 350, SAC Joint Venture, Sacramento, Calif.
Suita, K., Inoue, K., and Kanoh, N. (2002). “Strength and deformation of bolted beam-to-column connection accompanied by panel zone yield.” Proc., 4th Taiwan–Japan–Korea Joint Seminar on Earthquake Engineering for Building Structures, Seoul, Korea, 67–75.
Tsai, K. C., and Chen, W.-Z. (2000). “Seismic response of steel reducedbeam section to weak panel zone moment joints.” Proc., 3rd International Conf. STESSA 2000, Montréal.
Tsai, K. C., and Popov, E. P. (1988). “Steel beam-column joints in seismic moment resisting frames.” EERC Rep. No. UCB/EERC-88/19, Univ. of California, Berkeley, Calif.
Uang, C.-M. (1993). “An evaluation of two-level seismic design procedure.” Earthquake Spectra, 9(1), 121–135.
Uang, C.-M., and Fan, C.-C. (2001). “Cyclic stability criteria for steel moment connections with reduced beam section.” J. Struct. Eng., 127(9), 1021–1027.
Yu, Q. S., Gilton, C., and Uang, C.-M. (2000). “Cyclic response of RBS moment connections: Loading sequence and lateral bracing effects.” SAC/BD-00/22, SAC Joint Venture, Sacramento, Calif.
Zekioglu, A., Mozaffarian, H., Chang, K. L., and Uang, C.-M. (1997). “Designing after Northridge.” Modern Steel Constr., 37(3), 36–42.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: May 22, 2003
Accepted: Mar 16, 2005
Published online: Dec 1, 2005
Published in print: Dec 2005
Notes
Note. Associate Editor: Gregory A. MacRae
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.