Behavior of Cold-Formed High Strength Stainless Steel Sections
Publication: Journal of Structural Engineering
Volume 131, Issue 11
Abstract
This paper presents the behavior of cold-formed high strength stainless steel sections. The test specimens were cold-rolled from flat strips of duplex and high strength austenitic stainless steel. The material properties of high strength stainless steel square and rectangular hollow sections were determined. Tensile coupons at different locations in cross section were tested. Hence, the distributions of 0.2% proof stress and tensile strength measured in the cross section of cold-formed high strength stainless steel sections were plotted. The material properties of the complete cross section in the cold-worked state were also obtained from stub column tests. Detailed measurements of initial local geometric imperfections of the sections were obtained. The initial local plate imperfection profiles were plotted. Residual stress measurements of the high strength stainless steel sections were also conducted. The membrane and bending residual stress distributions in the cross section of the specimens were obtained. Furthermore, the stub column test strengths were compared with the design strengths.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgment
The writers are grateful to STALA Tube Finland for supplying the test specimens.
References
American Society of Civil Engineers (ASCE). (2002). “Specification for the design of cold-formed stainless steel structural members.” SEI/ASCE-8-02, Reston, Va.
Australian Standards (AS). (1991). “Methods for tensile testing of metals.” AS 1391, Standards Association of Australia, Sydney, Australia.
Australian/New Zealand Standard (AS/NZS). (2001). “Cold-formed stainless steel structures.” AS/NZS 4673:2001, Standards Australia, Sydney, Australia.
Denston, R. J., and White, J. D. (1977). “An electrical demountable extensometer.” CUED Technical Rep. No. CUED/C-Struct/TR.61.
Eurocode 3 (EC3). (1996). “Design of steel structures–Part 1.4: General rules—Supplementary rules for stainless steels.” European Committee for Standardization (CEN), Eurocode 3 ENV 1993-1-4, Brussels, Belgium.
Galambos, T. V., ed. (1998). Guide to stability design criteria for metal structures, 5th Ed., Wiley, New York.
Gardner, L. (2002). “A new approach to structural stainless steel design.” PhD thesis, Imperial College of Science, Technology and Medicine, London.
Johnson, A. L. (1966). “The structural performance of austenitic stainless steel members.” Rep. No. 327, Dept. of Structural Engineering, Cornell Univ., Ithaca, N.Y.
Korvink, S. A., van den Berg, G. J., and van den Merwe, P. (1995). “Web crippling of stainless steel cold-formed beams.” J. Constr. Steel Res., 34(2–3), 225–248.
Macdonald, M., Rhodes, J., and Taylor, G. T. (2000). “Mechanical properties of stainless steel lipped channels.” Proc., 15th International Specialty Conf. on Cold-Formed Steel Structures, R. A. LaBoube and W. W. Yu, eds., St. Louis, Univ. of Missouri, Rolla, Mo., 673–686.
Ramberg, W., and Osgood, W. R. (1943). “Description of stress strain curves by three parameters.” Technical Note No. 902, National Advisory Committee for Aeronautics, Washington, D.C.
Rasmussen, K. J. R., and Hancock, G. J. (1993). “Design of cold-formed stainless steel tubular members. I: Columns.” J. Struct. Eng., 119(8), 2349–2367.
Rasmussen, K. J. R., and Rondal, J. (1997). “Explicit approach to design of stainless steel columns.” J. Struct. Eng., 123(7), 857–863.
Talja, A., and Salmi, P. (1995). “Design of stainless steel RHS beams, columns and beam-columns.” VTT Research Notes 1619, Technical Research Centre of Finland, Espoo, Finland.
Wang, S. T. (1969). “Cold-rolled austenitic stainless steel: Material properties and structural performance.” Rep. No. 334, Dept. of Structural Engineering, Cornell Univ., Ithaca, N.Y.
Wang, S. T., Winter, G., and Errera, S. J. (1975). “Behavior of cold-rolled stainless steel members.” J. Struct. Div. ASCE, 101(11), 2337–2357.
Young, B., and Hartono, W. (2002). “Compression tests of stainless steel tubular members.” J. Struct. Eng., 128(6), 754–761.
Young, B., and Liu, Y. (2003). “Experimental investigation of cold-formed stainless steel columns.” J. Struct. Eng., 129(2), 169–176.
Yu, W. W. (2000). Cold-formed steel design, 3rd Ed., Wiley, New York.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Sep 17, 2004
Accepted: Jan 12, 2005
Published online: Nov 1, 2005
Published in print: Nov 2005
Notes
Note. Associate Editor: Scott A. Civjan
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.