Lower Slenderness Limits for Rectangular Reinforced Concrete Columns
Publication: Journal of Structural Engineering
Volume 131, Issue 1
Abstract
When designing a reinforced concrete column, most codes of practice specify that second order effects must be taken into account when the column slenderness exceeds a lower limit, usually associated to a certain loss of column carrying capacity. Such lower slenderness limits depend on the strength, stiffness, boundary conditions, and forces acting on the column. In this paper, simplified analytical expressions are presented for the lower slenderness limit of symmetrically reinforced rectangular columns. The limits, associated with a chosen (5 and 10%) loss of bearing capacity compared to nonslender columns, are derived based on general mechanics of concrete structures. The proposed formulae take into account the most important parameters governing the behavior of slender concrete columns, such as axial load, first order end eccentricities, ratio between permanent and total load, creep coefficient, amount and distribution of the reinforcement, and also different loading paths. Similar limits can readily be derived for section shapes other than the rectangular shape considered here. The results of the proposed formulae fit very well with those obtained by a nonlinear and time dependent analysis model previously developed and checked.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The present work has been developed under Research Project No. TRA1999-0974, funded by the Spanish Ministry of Science and Technology. The first writer also wants to express his gratitude to Professor Filip Filippou from the University of California at Berkeley for his suggestions and comments.
References
American Concrete Institute (ACI. (2002). “Building code requirements for reinforced concrete.” ACI 318-02, Detroit.
Bonet, J. L, Goberna, E., Fernández, M. A., and Miguel, P. (2001). “Lower slenderness bound for reinforced concrete columns.” Hormigón y Acero No. 219, Madrid, Spain, 79–89 (in Spanish).
Bridge, R. Q., and Seevaratnam, K. (1987). “The definition of a short column in reinforced concrete construction.” Proc., 1st National Structural Engineering Conf., Melbourne, Australia, 495–499.
British Standard Institution (BSI. (1997). “Structural use of concrete. Part 1. Code of practice for design and construction.” BS 8110, London.
Comité Euro-International du Beton (CEB. (1993). “CEB-FIP model code 1990.” CEB Bulletin No. 213–214, Lausanne, Switzerland.
Corres, H. (1986). “Slenderness limits for reinforced concrete slender columns.” Hormigón y Acero No. 101, Madrid, Spain, 35–52 (in Spanish).
Cruz, P. J. S., Marí, A., and Roca, P. (1998). “Nonlinear time-dependent analysis of segmentally constructed structures.” J. Struct. Eng. 124(3), 278–287.
European Committee for Standardization (CEN. (2002). “Design of concrete structures, part 1: General rules and rules for buildings.” Eurocode 2, prEN 1992-1-1, Belgium.
Hellesland, J. (1990). “New NS 3473—When is a compression member slender?” Betongprodukter, J. Norwegian Precasting Federation (NBIF), 22 (1), XXX–XXX (in Norwegian).
Hellesland, J. (1993). “Applicability of normal grade slenderness limits to HSC and LWA columns.” Proc., 3rd. Int. Symp. on Utilization of High Strength Concrete, Vol.1, Lillehammer, Norway, 209–216.
Hellesland, J. (1999). “On column slenderness limits.” Research Rep. in Mechanics, Mechanics Division, Univ. of Oslo, Norway.
MacGregor, J. G. (1993). “Design of slender concrete columns—revisited.” ACI Struct. J., 90(3), 302–309.
MacGregor, J. G., Breen, J. E., and Pfrang, E. O. (1970). “Design of slender concrete columns.” ACI J., 67(1), 6–28.
Marí, A. (1984). “Nonlinear geometric, material and time dependent analysis of three dimensional reinforced and prestressed concrete frames.” UCSM Rep. No. 84-1, Dept. of Civil Engineering, Univ. of California, Berkeley, Calif.
Marí, A. (2000). “Numerical simulation of the segmental construction of three dimensional concrete frames.” Eng. Struct., 22, 585–596.
Marí, A., and Hellesland, J. (2003). “When can second order effects in columns be neglected?” Research Rep. No. 2003-01, Dept. of Construction Engineering, Univ. Politècnica de Catalunya, Barcelona, Spain.
Marí, A., and Valdés, M. (2000). “Long-term behavior of continuous precast concrete girder bridge model.” J. Bridge Eng., 5(1), 22–30.
McDonald, B. E. (1986). “Second order effects in R.C. frames.” MASc thesis, Univ. Of Waterloo, Waterloo, Ontario, Canada.
Menegotto, M. (1983). “Observations on slenderness bounds for R/C columns.” CEB Bulletin d’Information 155, Comité Euro-International du Beton, Lausanne, Switzerland, 5–28.
Norwegian Standard Association (NSF. (1992). “Concrete structures: Design rules.”English Ed., NS 3473, Oslo, Norway.
Río, O., and Morán, F. (1987). “Slenderness limits for reinforced concrete columns: 1. Lower limit.” Hormigón y Acero, No. 160, Madrid, Spain, 31–38 (in Spanish).
Robinson, J., Fouré, F., and Bourghli, M. (1975). “Le flambement des poteaux en béton armé chargés avec des excentricités differentes à leurs extrémités.” Annales I.T.B.T.P., 333, 46–74.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 131 • Issue 1 • January 2005
Pages: 85 - 95
Copyright
© ASCE.
History
Received: Jan 6, 2003
Accepted: Mar 26, 2004
Published online: Jan 1, 2005
Published in print: Jan 2005
Notes
Note. Associate Editor: Dat Duthinh
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.