Structural Assessment of Corroded Reinforced Concrete Beams: Modeling Guidelines
Publication: Journal of Structural Engineering
Volume 130, Issue 8
Abstract
The evolution of the structural behavior in reinforced concrete beams subjected to reinforcement corrosion is studied here, by developing a suitable numerical procedure, which is validated by comparison with available test data. There are two objectives of this study: The understanding of the many aspects of the progressive damage in an existing structure (cracking and crushing, bar yielding, bond failure), and the assessment of the actual safety level. Nonlinear finite element analysis is used; the effects of corrosion are modeled by reducing the geometry of the finite elements representing separately the steel bars and the concrete, and by modifying the constitutive laws of the materials (steel and concrete) and of their interface (bond). Both the service and ultimate limit states are studied, showing the importance of the following phenomena: (1) Stiffness decay because of impaired tension stiffening, (2) crack pattern evolution accompanied by enhanced shear effects, (3) strength deterioration in bending and shear, (4) transition from tension to compression-triggered failures in critical sections, and (5) bond failure along the span and/or at beam ends. With reference to the last issue, the introduction of a specific model for bond deterioration appears to be of paramount importance in order to evaluate the residual ductility of a structure.
Get full access to this article
View all available purchase options and get full access to this article.
References
Al-Sulaimani, G. J., Kaleemullah, M., Basumbul, I. A., and Rasheeduzzafar.(1990). “Influence of corrosion and cracking on bond behavior and strength of reinforced concrete members.” ACI Struct. J., 87(2), 220–231.
Auyeung, Y., Balaguru, P., and Chung, L.(2000). “Bond behavior of corroded reinforcement bars.” ACI Mat. J., 97(2), 214–220.
American Concrete Institute (ACI). (1995). “Building code requirements for structural concrete.” ACI 318M-95, Farmington Hills, Mich., 371.
Balakrishnan, S., and Murray, D. W.(1988). “Concrete constitutive model for NLFE analysis of structures.” J. Struct. Eng., 114(7), 1449–1466.
Berra, M., Castellani, A., Ciccotelli, S., and Coronelli, D.(1994). “Bond slip effects on reinforced concrete elements under earthquake loading.” Eur. Earthquake Eng., 3, 3–10.
Bungey, J. H. (1982). The testing of concrete in structures, Surrey University Press, London (Chapman and Hall, New York), 207.
Cairns, J., and Zhao, Z.(1993). “Behavior of concrete beams with exposed reinforcement.” Proc., Inst. Civ. Eng., Struct. Build., 99, 141–154.
Cairns, J., and Millard, S. (1999). “Section 13.2: Reinforcement corrosion and its effect on residual strength of concrete structures.” Proc., 8th Int. Conf. on Structure Faults and Repair, M. Forde, ed., Engineering Technics Press, Edinburgh, U.K. (CD-ROM).
Capè, M. (1999). “Residual service-life assessment of existing R/C structures.” MS thesis, Chalmers Univ. of Technology, Göteborg (Sweden) and Milan Univ. of Technology (Italy, Erasmus Program), 133.
Castel, A., Francois, R., and Arliguie, G.(2000). “Mechanical behavior of corroded reinforced concrete beams. II: Bond and notch effects.” Mater. Struct., 33, 545–551.
Castellani, A., and Coronelli, D. (1999). “Section 13.7: Beams with corroded reinforcement: Evaluation of the effects of cross section losses and bond deterioration by finite element analysis.” Proc., 8th Int. Conf. on Structure Faults and Repair ‘99,’ M. Forde, ed., Engineering Technics Press, Edinburgh, U.K. (CD-ROM).
CEN. (1998). “EuroCode 8: Design Provisions for earthquake resistance of buildings. 1–4: Strengthening and repair of buildings.” Draft prENV 1998-1-4, Brussels, Belgium, 111.
Cervenka, V.(1985). “Constitutive model for cracked reinforced concrete.” ACI Struct. J., 82(6), 877–892.
Clark, L. A., and Thorogood, P.(1985). “Shear strength of concrete beams in hogging regions.” Proc., Inst. Civ. Eng., Struct. Build 79, 327–348.
Comité Euro-International du Béton (CEB). (1998). “Strategies for testing and assessment of concrete structures,” Bulletin 243, CEB-FIB, Lausanne (CH), Switzerland, 184.
Comité Euro-International du Béton-Federation International du Betón (CEB-FIB). (1993). “Model Code 90” (final draft), Bulletin 203, Lausanne (CH), Switzerland, 637.
Coronelli, D.(2002). “Corrosion cracking and bond strength modelling for corroded bars in reinforced concrete.” ACI Struct. J., 99(3), 267–276.
Coronelli, D., and Mulas, M. G.(2001). “Local-global approach in the seismic analysis of R/C frames including bond slip effects.” Eng. Struct., 23, 911–925.
De Borst, R.(1997). “Some recent developments in computational modelling of concrete fracture.” Int. J. Fract., 86, 5–36.
Eligehausen R., Popov, E. P., and Bertero V. V. (1983). “Local bond stress-slip relationships of deformed bars under generalized excitations.” Rep. No. UCB/EERC 83-23, Univ. of California, Berkeley, Calif.
Federation International du Béton FIB. (2000). “Bond of reinforcement in concrete.” State of the Art Report—Bulletin 10—Task Group Bond Models, Lausanne (CH), 427.
Lee, H. S., Kage, T., Noguchi, T., and Tomosawa, F. (1999). “The evaluation of flexural strength of RC beams damaged by rebar corrosion.” Proc., 8th Int. Conf. on Durable Building Materials and Components, Naional Research Council, Ottawa, Ont., Canada, 31, 320–330.
Leonhardt, F. (1977). Vorlesungen uber Massivbau Vol. 3, Springer, Berlin, 256.
Jirasek, M., and Zimmermann, T.(1998). “Rotating crack model with transition to scalar damage.” J. Eng. Mech., 124(3), 277–284.
Melchers, R. E.(2001). “Assessment of existing structures—approaches and research needs.” J. Struct. Eng., 127(4), 406–411.
Menegotto, M., and Pinto, P. (1973). “Methods of analysis for cyclically loaded R/C frames.” Proc., Symp. on Resistance and Ultimate Deformability of Structure Acted by Well Defined Repeated Load, International Association for Bridge and Structural Engineering, Lisbon, Portugal.
Molina, F. J., Alonso, C., and Andrade, C.(1993). “Cover cracking as a function of rebar corrosion. II: Numerical model.” Mater. Struct., 26, 532–548.
Catbas, F. Necati, and Emin Aktan, A.(2002). “Condition and damage assessment: Issues and some promising indices.” J. Struct. Eng., 128(8), 1026–1036.
Palsson, R., and Mirza, M. S.(2002). “Mechanical response of corroded steel reinforcement of abandoned concrete bridge.” ACI Struct. J., 99(2), 157–162.
Plizzari, G. A., Marchina, E., and Giuriani, E.(1996). “Experimental study of splitting and flexural cracks in a R/C beam with overlapped splices.” Mater. Struct., 29, 19–27.
Rodriguez, J., Ortega, L., and Garcia, A. (1994). “Corrosion of reinforcing bars and service life of R/C structures: Corrosion and bond deterioration.” Proc., Int. Conf. on Concrete across Borders, Vol. II, 315–326.
Rodriguez, J., Ortega, L., and Casal, J. (1995). “Load carrying capacity of concrete structures with corroded reinforcement.” 4th Int. Conf. on Structure Faults and Repair, M. Forde, ed., Engineering Tech. Press, Edinburgh, U.K., 189–199.
Rodriguez, J., Ortega, M., Casal, J., and Diez, M. D. (1996a). “Assessing structural conditions of concrete structures with corroded reinforcement.” Proc., Int. Conf. on Concrete in the Service of Mankind, Sess. 5, Dundee, Scotland, R. K. Dhir and N. A. Henderson, eds., E-&-FN Spon, London, 141–150.
Rodriguez, J., Ortega, M., and Casal, J. (1996b). “Load bearing capacity of concrete columns with corroded reinforcement.” Proc., 4th Int. Symp. on Corrosion of Reinforcement in Concrete Construction, C. L. Page, P. B. Bamforth, J. W. Figg, eds., The Royal Society of Chemistry, Cambridge, U.K.
Rots, J. G., and Blaauwendraad, J.(1989). “Crack models for concrete: Discrete or smeared? Fixed, multidirectional, or rotating?.” Heron, 34(1), 45–49.
Sarveswaran, V., Roberts, M. B., and Ward, J. A.(2000). “Reliability assessment of deteriorating reinforced concrete beams.” Proc., Inst. Civ. Eng., Struct. Build., 140(3), 239–247.
Stanysh, K., Hooton, R. D., and Pantazopoulou, S. J.(1999). “Corrosion effects on bond strength in RC.” Struct. J., 96(6), 915–921.
Stevens N., Uzumeri S., and Collins M. (1987). “Analytical modelling of R/C subjected to monotonic and reversed loading.” SP No. 87-1, Dept. of Civil Engineering, Univ. of Toronto, Toronto.
Tachibana Y., Maeda, K., Kaikawa, Y., and Kawamura, M. (1990). “Mechanical behavior of RC beams damaged by corrosion of reinforcement.” Corrosion of reinforcement in concrete, C. Page, K. Treadaway, and P. Bamforth, eds., Elsevier Applied Science for the Society of Chemical Industry, U.K., 178–187.
Ting, S., and Nowak, A.(1991). “Effect of reinforcing steel area loss on flexural behavior of RC beams.” ACI J. Struct Eng., 88(3), 309–314.
Tracy, R. G., and Klein, R.(1994). “Corrosion-induced slab liftoff.” Concr. Int., 16(3), 35–38.
Vecchio, F. J.(2001). “Nonlinear finite element analysis of reinforced concrete: At the crossroads?” Struct. Concr., 2(4), 201–212.
Vecchio, F., and Collins, M. P.(1986). “The modified compression field theory for reinforced concrete elements subjected to shear.” Proc. ACI, 83(2), 219–231.
Yuan, Y., and Marosszeky, M.(1991). “Analysis of corroded reinforced concrete sections for repair.” J. Struct. Eng., 117(7), 2018–2034.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Nov 1, 2001
Accepted: Mar 16, 2004
Published online: Jul 15, 2004
Published in print: Aug 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.