Analysis and Design of Double-Sided High-Rise Steel Pallet Rack Frames
Publication: Journal of Structural Engineering
Volume 130, Issue 7
Abstract
In routine design of steel storage rack frames, it is far more common to perform two dimensional (2D) rather than three dimensional (3D) linear buckling analyses. In this paper, it is demonstrated that the global buckling behavior of high-rise steel storage rack frames may not be revealed by 2D buckling analyses as 3D interaction modes are involved. It is shown that the monosymmetric upright columns of a high-rise rack frame fail in a flexural–torsional mode due to the shear-center eccentricity of the sections, and that the 3D frame buckling analysis is more reliable in determining the critical members of a rack frame. Current steel storage rack design standards combine independent 2D flexural buckling analyses and simplified flexural–torsional buckling analysis of individual columns to account for 3D behavior. Comparisons between the buckling stresses of the rack columns determined from 3D buckling analyses and the buckling stresses determined in accordance with the steel storage racking standards are presented. It is concluded that the use of 2D analysis based procedures can lead to poorly proportioned pallet rack structures in terms of safety or economy. By comparing the buckling analysis results using 3D beam elements of varying degrees of refinement to each other, it is also demonstrated that the beam elements available in most commercial frame analysis programs are not sufficiently refined for accurate 3D buckling analyses of high-rise rack frames composed of monosymmetric thin-walled open sections.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Iron and Steel Institute (AISI). (1996). “Specification for the design of cold-formed steel structural members.” Washington, D.C.
American Society of Civil Engineers (ASCE). (1997). “Effective length and notional load approaches for assessing frame stability: Implications for American steel design.” New York.
Aristizabal-Ochoa, J. D.(1997). “Story stability of braced, partially braced and unbraced frames: Classical approach.” J. Struct. Eng., 123(6), 799–807.
Attard, M. M.(1992). “Flexural–torsional buckling of mono-symmetric columns.” J. Constr. Steel Res., 23(2), 117–126.
Baldassino, N., Bernuzzi, C., and Zandonini, R. (2000). “Experimental analysis on key components of steel storage pallet racking systems.” Proc., Structural Failure and Plasticity, Melbourne, X. L. Zhao and R. H. Grzebieta, eds., Pergamon, Amsterdam, The Netherlands, 859–864.
Baldassino, N., and Hancock, G. J. (1999). “Distortional buckling of cold-formed steel storage rack sections including perforations.” Proc., Light-Weight Steel and Aluminium Structures, Helsinki, P. Makelainen and P. Hassinen, eds., Elsevier Science, Amsterdam, The Netherlands, 131–138.
Bridge, R. Q., and Fraser, D. J.(1987). “Improved G-factor method for evaluating effective lengths of columns.” J. Struct. Eng., 113(6), 1341–1356.
Chajes, A., and Winter, G.(1965). “Torsional-flexural buckling of thin-walled members.” J. Struct. Div. ASCE, 91(4), 103–124.
Chan, S. L., and Zhou, Z. H.(1994). “Pointwise equilibrium polynomial element for nonlinear analysis of frames.” J. Struct. Eng., 120(6), 1703–1717.
Cheong-Siat-Moy, F.(1986). “K-factor paradox.” J. Struct. Eng., 112(8), 1747–1760.
Cheong-Siat-Moy, F. (1995). “Misconceptions regarding the K-factor.” Proc., Structural Stability and Design, Sydney, S. Kitipornchai, G. J. Hancock, and M. A. Bradford, eds., A. A. Balkema, Rotterdam, The Netherlands, 243–248.
Cheong-Siat-Moy, F.(1999). “An improved K-factor formula.” J. Struct. Eng., 125(2), 169–174.
Conci, A.(1992). “Large displacement analysis of thin-walled beams with generic open section.” Int. J. Numer. Methods Eng., 33(12), 2109–2127.
Conci, A., and Gattass, M.(1990). “Natural approach for geometric nonlinear analysis of thin-walled frames.” Int. J. Numer. Methods Eng., 30(2), 207–231.
Davies, J. M. (1992). “Down-aisle stability of rack structures.” Proc., 11th Int. Specialty Conf. Cold-Formed Steel Structures, St. Louis, 417–435.
Duan, L., and Chen, W. F.(1988). “Effective length factors for columns in braced frames.” J. Struct. Eng., 114(10), 2357–2370.
Duan, L., and Chen, W. F.(1989). “Effective length factors for columns in unbraced frames.” J. Struct. Eng., 115(1), 149–165.
Dunai, L., Hegedus, T., Kaltenbach, L., and Adany, S. (1997). “Experimental and numerical studies on the stability of racking frames.” Stability and Ductility of Steel Structures, T. Usami, ed., Japanese Society of Steel Construction, Tokyo, 647–652.
Essa, H.(1997). “Stability of columns in unbraced frames.” J. Struct. Eng., 123(7), 952–957.
Federation Europeene de La Manutention (FEM). (1998). “Recommendations for the design of static steel pallet racking and shelving.” FEM 10.2.02, FEM, Birmingham, U.K.
Godley, M. H. R., Beale, R. G., and Feng, X.(2000). “Analysis and design of down-aisle pallet rack structures.” Comput. Struct., 77(4), 391–401.
Hancock, G. J.(1985). “Distortional buckling of steel storage rack columns.” J. Struct. Eng., 111(12), 2770–2783.
Hancock, G. J., Murray, T. M., and Ellifritt, D. S. (2001). Cold-formed steel structures to the AISI specification, Marcel Dekker, New York.
Hellesland, J., and Bjorhovde, R.(1996). “Improved frame stability analysis with effective lengths.” J. Struct. Eng., 122(11), 1275–1283.
Hsiao, K. M., and Lin, W. Y.(2000). “A co-rotational formulation for thin-walled beams with mono-symmetric open sections.” Comput. Methods Appl. Mech. Eng., 190(8–10), 1163–1185.
Hsiao, K. M., and Lin, W. Y.(2001). “Co-rotational formulation for geometric nonlinear analysis of doubly symmetric thin-walled beams.” Comput. Methods Appl. Mech. Eng., 190(45), 6023–6052.
Jennings, A.(1968). “Frame analysis including change in geometry.” J. Struct. Div. ASCE, 94(3), 627–644.
Kishi, N., Chen, W. F., and Goto, Y.(1997). “Effective length factor of columns in semirigid and unbraced frames.” J. Struct. Eng., 123(3), 313–320.
Lewis, G. M.(1991). “Stability of rack structures.” Thin-Walled Struct., 12(2), 163–174.
Li, T. Q., Choo, B. S., and Nethercot, D. A.(1995). “Connection element method for the analysis of semi-rigid frames.” J. Constr. Steel Res., 32(2), 143–171.
Meek, J. L., and Tan, H. S.(1984). “Geometrically nonlinear analysis of space frames by an incremental iterative technique.” Comput. Methods Appl. Mech. Eng., 47(3), 261–282.
Olsson, A. M. J., Sandberg, G. E., and Austrell, P. E.(1999). “Load-carrying capacity of damaged steel columns with channel sections.” J. Struct. Eng., 125(3), 338–343.
Pekoz, T. (1979). “Design of cold-formed storage racks.” Proc., Int. Conf. Thin-Walled Structures: Recent Technology Advance and Trends in Design, Research and Construction, Glasgow, Scotland, 145–159.
Rack Manufacturers Institute (RMI). (1997). “Specification for design, testing and utilization of industrial steel storage racks.” Charlotte, N.C.
Roos, O., and Hancock, G. J. (1986). “Flexural–torsional buckling of storage rack columns.” Proc., 8th Int. Specialty Conf. Cold-Formed Steel Structures, Univ. of Missouri-Rolla, St. Louis.
Smith, B. S., and Cruvellier, M.(1991). “General planar model for analysing high-rise structures.” J. Struct. Eng., 117(11), 3228–3238.
Standards Association of Australia (SAA). (1981). “SAA steel structures code.” AS 1250-1981, SAA, Homebush, Australia.
Standards Australia (SA). (1993a). “Steel storage racking.” AS 4084-1993, Homebush, New South Wales, Australia.
Standards Australia (SA). (1993b). “Steel storage racking—Commentary.” Supplement to AS 4084-1993, Homebush, New South Wales, Australia.
Standards Australia (SA). (1998). “Steel structures.” AS 4100-1998, Homebush, New South Wales, Australia.
Standards Australia/Standards New Zealand (SA/SNZ). (1996). “Cold-formed steel structures.” SA/SNZ 4600:1996, SA/SNZ, Homebush, Australia.
Teh, L. H. (1998). “Towards 3D plastic-zone advanced analysis of steel frames.” PhD thesis, Univ. of Sydney, Sydney, Australia.
Teh, L. H.(2001). “Cubic beam elements in practical analysis and design of steel frames.” Eng. Struct., 23(6), 631–642.
Teh, L. H., and Clarke, M. J.(1997). “New definition of conservative internal moments in space frames.” J. Eng. Mech., 123(2), 97–106.
Teh, L. H., and Clarke, M. J.(1998). “Co-rotational and Lagrangian formulations of elastic three-dimensional beam finite elements.” J. Constr. Steel Res., 48(2–3), 123–144.
Teh, L. H., and Clarke, M. J.(1999). “Symmetry of tangent stiffness matrices of 3D elastic frame.” J. Eng. Mech., 125(2), 248–251.
Tide, R. H. R., and Calabrese, F. A. (1998). “Investigation of collapsed rack storage systems.” Thin-walled structures, N. E. Shanmugam et al., eds., Elsevier, Oxford, U.K., 493–500.
Timoshenko, S. P., and Gere, J. M. (1961). Theory of elastic stability, 2nd Ed., McGraw-Hill, New York.
Trahair, N. S. (1993). Flexural–torsional buckling of structures, E&FN Spon, London.
White, D. W., and Hajjar, J. F.(1997). “Buckling models and stability design of steel frames: A unified approach.” J. Constr. Steel Res., 42(3), 171–207.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Aug 7, 2000
Accepted: Nov 4, 2003
Published online: Jun 15, 2004
Published in print: Jul 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.