Cyclic Bending Tests to Determine Fully Ductile Section Slenderness Limits for Cold-Formed Circular Hollow Sections
Publication: Journal of Structural Engineering
Volume 130, Issue 7
Abstract
This paper determines new section slenderness limits suitable for design and construction of seismic resisting structural systems. It describes an experimental investigation of the cyclic inelastic flexural behavior of cold-formed circular hollow section (CHS) beams. Controlled-rotation, symmetrical cyclic bending tests were performed on different sizes compact CHS with section slenderness ranging from 13 to 39. With continuous cycling, the growth of ovalization caused a progressive reduction in the bending rigidity of the tube and eventually an instability occurred. The CHS beams exhibited stable hysteresis behavior up to local buckling and then showed considerable degradation in strength and ductility depending upon the ratio. Seismic capacity parameters are presented, including strength, stiffness, hysteresis loops and modes of failure for each specimen. Peak moments obtained in the cyclic tests were compared with those obtained in monotonic tests published previously and also with design moments predicted using a number of steel specifications. The deformation ductility demand was determined and used to derive new fully ductile section slenderness limits suitable for seismic design. A comparison is made between these seismic slenderness limits and the static limits available in the design codes.
Get full access to this article
View all available purchase options and get full access to this article.
References
Architecture Institute of Japan (AIJ). (1990). “Recommendations for the design and fabrication of tubular structures in steel.” AIJ, Tokyo.
American Institute of Steel Construction (AISC). (1997). “Seismic provisions for structural steel buildings.” American Inst. for Steel Construction, Chicago.
American Institute of Steel Construction (AISC). (2000). “Load and resistance factor design specification for steel hollow structural sections.” American Inst. of Steel Construction, Chicago.
American Institute of Steel Construction–Load Resistance Factor Design (AISC-LRFD). (1999). “Load and resistance factor design specification for structural steel buildings.” American Inst. of Steel Construction, Chicago.
American Iron and Steel Institute (AISI). (1996). “Cold-formed steel design manual.” American Iron and Steel Inst., Washington, D.C.
Anastasiadis, A., Gioncu, V., and Mazzolani, F. M. (2001). “New Trends in the evaluation of available ductility of steel members.” Behaviour of steel structures in seismic zones. Proc., 3rd Int. Conf. STESSA, F. M. Mazzolani, and R. Tremblay, eds, Balkema, Rotterdam, The Netherlands, 3–17.
Australian Standards (AS). (1991). “Structural steel hollow sections.” AS 1163, Standards Association of Australia, Sydney, Australia.
Australian Standards (AS). (1991). “Methods for tensile testing of metals.” AS 1391, Standards Association of Australia, Sydney, Australia.
Australian Standards (AS). (1993). “Minimum design loads on structures, Part 4: Earthquake loads.” AS 1170, Standards Association of Australia, Sydney, Australia.
Australian Standards (AS). (1998). SAA steel structures code.” AS 4100, Standards Association of Australia, Sydney, Australia.
Australian Standards/New Zealand Standards (AS/NZS). (1996). “Cold-formed steel structures.” AS/NZS 4600, Standards Association of Australia, Australian/New Zealand Standard, Sydney, Australia.
American Society for Testing and Materials (ASTM). (1984). “Cold-formed welded and seamless carbon steel structural tubing in rounds and shapes.” ASTM-A500, Philadelphia.
Canadian Standards Association (CAN-CSA). (1989). “Steel structures for buildings, limit states design.” CAN-CSA S16.1, Canadian Standards Associations.
Chen, W. F., and Ross, D. A.(1977). “Tests of fabricated tubular columns.” J. Struct. Div. ASCE, 103(3), 619–634.
Chopra, A. K., and Newmark, N. M. (1980). Design of earthquake resistant structures, Wiley, New York.
Comité International pour la Développement et l’Étude de la Construction Tubulaire (CIDECT). (1996). Structural stability of hollow sections, J. Rondal, K.-G. Wuker, D. M. Dutta, J. Wardenier, and N. Yeomans, eds., CIDECT Series on Construction with Hollow Steel Sections, TUV Reinland, Cologne, Germany, No. 2.
Elchalakani, M., Zhao, X. L., and Grzebieta, R. H.(2002a). “Plastic slenderness limit for cold-formed circular steel hollow sections.” Austral. J. Struct. Eng., 3(3), 1–16.
Elchalakani, M., Zhao, X. L., and Grzebieta, R. H.(2002b). “Bending tests to determine slenderness limits for cold-formed circular hollow sections.” J. Constr. Steel Res., 58(11), 1407–1430.
Elchalakani, M., Zhao, X. L., and Grzebieta, R. H.(2003). “Tests of cold-formed circular tubular braces under cyclic axial loading.” J. Struct. Eng., 129(4), 507–514.
Eurocode 3. (1992). “Design of steel structures, Part 1.1, General rules and rules for buildings.” ENV 1993 1–1, European Committee for Standardization, Brussels.
Eurocode 8. (1996). “Design provisions for earthquake resistance of structures, Part 1.1, General rules, seismic actions and general requirements for structures.” ENV 1-1, European Committee for Standardization, Brussels.
European Convention for Construction Steelwork (ECCS). (1991). ECCS-TWG 1.3. “Seismic design, European recommendations for steel structures in seismic zones, European Convention for Structural Steel Work.”
Galambos, T. V. (1998). Guide to stability design criteria for metal structures, 5th Ed., Structural Stability Research Council, Wiley, New York.
Gao, S. B., Usami, T., and Ge, H. B.(1998). “Ductility of steel short cylinders in compression and bending.” J. Eng. Mech., 124(2), 176–183.
Grzebieta, R., Zhao, X. L., and Purza, F. (1997). “Multiple low cycle fatigue of SHS subjected to gross pure bending deformations.” Proc., 5th Int. Colloq. on Stability and Ductility of Steel Structures, T. Usami, ed., 1, 847–854.
Hancock, G. J. (1998). Design of cold-formed steel structures to Australian New Zealand Standard AS/NZS 4600:1996, 3rd Ed., Australian Institute of Steel Construction, Sydney, Australia.
Heavy Engineering Research Association (HERA). (1995). “Seismic design of steel structures.” Heavy Engineering Research Association, HERA Rep. No. R4-76, M. J. Feeney and G. C. Clifton, eds., Wellington, New Zealand.
Jain, A. K., Goel, S. C., and Hanson, R. D.(1978). “Inelastic response of restrained steel tubes.” J. Struct. Div. ASCE, 104(6), 897–910.
Jain, A. K., Goel, S. C., and Hanson, R. D.(1980). “Hysteresis cycles of axially loaded steel members.” J. Struct. Div. ASCE, 106(8), 1777–1795.
Japanese Road Association (JRA). (1996). “Specifications for highway bridges. Part V: Seismic design.” Japanese Highway Association, Tokyo.
Krawinkler, H., Akshay, G., Medina, R., and Luco, M. (2000). “Development of loading histories for testing of steel beam-to-column assemblies.” Rep. prepared for SAC Steel Project, Dept. of Civil and Environmental Engineering, Stanford Univ., Stanford, Calif.
Kunnath, S. K., and Malley, J. O.(2000). “Seismic behavior and design of steel moment frames: Aftermath of the 1994 Northridge earthquake.” J. Struct. Eng., 126(1), 4–9.
Lee, C., Grzebieta, R. H., and Zhao, X. L. (2001). “Cyclic bending of beams made of a cold-formed SHS C450 tube.” Proc., 6th Pacific Structural Steel Conf., China Steel Construction Society, Beijing, 648–653.
Liu, Z., and Goel, S. C.(1988). “Cyclic load behavior of concrete-filled tubular braces.” J. Struct. Eng., 114(7), 1488–1506.
MacRae, G. A. (1990). “The seismic response of steel frames.” Dept. of Civil Engineering Research Rep., The Univ. of Canterbury, Christchurch, New Zealand.
Maison, B. F., and Popov, E. P.(1980). “Cyclic response prediction for braced steel frames.” J. Struct. Div. ASCE, 106(7), 1401–1416.
New Zealand Standards (NZS). (1992). “Standards New Zealand, code of practice for general structural design and design loading for buildings, and commentary.” NZS 4203, Wellington, New Zealand, Parts 1 and 2.
New Zealand Standards (NZS). (1997). “Standards New Zealand, steel structures standard.” NZS 3404, Wellington, New Zealand, Part 1.
Popov, E. P., and Black, R. G.(1981). “Steel struts under severe cyclic loadings.” J. Struct. Div. ASCE, 107(9), 1857–1881.
Popov, E. P., Zayas, V. A., and Mahin, S. A.(1979). “Cyclic inelastic buckling of thin tubular columns.” J. Struct. Div. ASCE, 105(11), 2261–2277.
SAC Joint Venture. (1995). “Analytical and field investigations of buildings affected by the Northridge earthquake of January 17, 1994.” SAC Rep. No. 95-04, Part 2.
Sherman, D. (1980). “Postlocal buckling behavior of tubular strut type beam columns: An experimental study.” Technical Rep., Dept. of Civil Engineering, Univ. of Wisconsin, Milwaukee.
Sherman, D. R. (1986). “Inelastic flexural buckling of cylinders.” Proc., Invited papers for the Int. Conf., Steel structures—Recent research advance and their applications to design, M. N. Pavlovic, ed., Elsevier Applied Science, London, 339–356.
Sherman, D., and Sully, R. (1994). “Tubular bracing members under cyclic loading.” Proc., 4th Pacific Structural Steel Conf, Singapore Steel Structures Society, Singapore.
Sherman, D., Mueller, W. H., and Erzurumlu, H.(1979). “Behavioral study of circular tubular beam-columns.” J. Struct. Div. ASCE, 105(6), 1055–1068.
Usami, T., and Ge, H. B.(1998). “Cyclic behaviour of thin-walled steel structures, numerical analyses.” Thin-Walled Struct., 32(1/3), 41–80.
Usami, T., and Ge, H. B. (2000). “Failure predictions of thin-walled steel structures.” Proc., 7th Int. Symp. on Structural Failure and Plasticity, Implast 2000, X. L. Zhao, and R. H. Grzebieta, eds., Balkema, Rotterdam, The Netherlands, 53–54.
Usami, T., Banno, S., Zetsu, H., and Aoki, T.(1993). “An experimental study on elastic-plastic behaviour of compression members under cyclic loading—Effect of loading program.” Jpn. J. Struct. Eng., 39A(3), 235–247 (in Japanese).
Yura, J. A., Galambos, T. V., and Ravindra, M. K.(1978). “The bending resistance of steel beams.” J. Struct. Div. ASCE, 10(ST9), 1355–1370.
Zayas, V. A., Popov, E. P., and Mahin, S. A. (1980). “Cyclic inelastic buckling of tubular steel braces.” Rep. No. UCB/EERC-80/16, Earthquake Engineering Research Center, Univ. of California at Berkeley, Berkeley, Calif.
Zhao, X. L., and Grzebieta, R.(1999). “Void-filled SHS beams subjected to large deformation cyclic bending.” J. Struct. Eng., 125(9), 1020–1029.
Zhao, X. L., Grzebieta, R., and Lee, C.(2002). “Void-filled cold-formed rectangular hollow section braces subjected to large deformation cyclic axial loading.” J. Struct. Eng., 128(6), 746–753.
Zheng, Y., Usami, T., and Ge, H.(2000). “Ductility evaluation procedure for thin-walled steel structures.” J. Struct. Eng., 126(11), 1312–1319.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Mar 11, 2003
Accepted: Jul 29, 2003
Published online: Jun 15, 2004
Published in print: Jul 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.