Tests and Design of Fixed-Ended Cold-Formed Steel Plain Angle Columns
Publication: Journal of Structural Engineering
Volume 130, Issue 12
Abstract
This paper presents a series of tests on cold-formed steel plain (unstiffened) angle columns compressed between fixed ends. The test specimens were brake-pressed from high strength structural steel sheets. Tests were performed over a range of lengths such that column curves could be obtained. Geometric imperfections and material properties of the specimens were measured. The test strengths are compared with the design strengths calculated using the American Specification and Australian/New Zealand Standard for cold-formed steel structures. The required additional moment as specified in the Specification and Standard was not included in calculating the design strengths for slender and nonslender angle sections. It is shown that the design strengths predicted by the Specification and Standard are generally very conservative. Design equations for cold-formed steel plain angle columns are proposed, which are modified from the current design equations in the Specification and Standard. It is shown that the proposed design rules provide much more accurate results compared with the current design rules for both slender and nonslender fixed-ended angle sections. A reliability analysis was performed to assess the reliability of the current and proposed design rules.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Institute of Steel Construction (AISC). ( 1993). “Load and resistance factor design Specification for structural steel buildings.” Chicago.
2.
American Iron and Steel Institute (AISI). ( 1996). “Specification for the design of cold-formed steel structural members.” Washington, D.C.
3.
American Society of Civil Engineers (ASCE). ( 1998). “Minimum design loads for buildings and other structures.” ASCE Standard 7-98, ASCE, Reston, Va.
4.
Australian Standard. ( 1991). “Methods for tensile testing of metals.” AS 1391, Standards Association of Australia, Sydney, Australia.
5.
Australian Standard. ( 1993). “Steel sheet and strip—hot-dipped zinc-coated or aluminium/zinc-coated.” AS 1397, Standards Association of Australia, Sydney, Australia.
6.
Australian/New Zealand Standard (AS/NZS). ( 1996). “Cold-formed steel structures.” AS/NZS 4600:1996, Standards Australia, Sydney, Australia.
7.
Dhanalakshmi, M., and Shanmugam, N. E. (2001). “Design for openings in equal-angle cold-formed steel stub columns.” Thin-Walled Struct., 39, 167–187.
8.
, T. V. Galambos, ed. ( 1998). Guide to stability design criteria for metal structures, 5th Ed., Wiley, New York.
9.
North American Specification (NAS). ( 2001). “North American Specification for the design of cold-formed steel structural members.” North American Cold-formed Steel Specification, American Iron and Steel Institute, Washington, D.C.
10.
Peköz, T.B. ( 1987). “Development of a unified approach to the design of cold-formed steel members.” Rep. No. CF 87-1, American Iron and Steel Institute, Washington, D.C.
11.
Peköz, T.B., and Hall, W.B. ( 1988). “Probabilistic evaluation of test results.” Proc., 9th Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, Mo.
12.
Popovic, D., Hancock, G. J., and Rasmussen, K. J. R. (1999). “Axial compression tests of cold-formed angles.” J. Struct. Eng., 125(5), 515–523.
13.
Popovic, D., Hancock, G. J., and Rasmussen, K. J. R. (2001). “Compression tests on cold-formed angles loaded parallel with a leg.” J. Struct. Eng., 127(6), 600–607.
14.
Trahair, N. S. (2002a). “Bearing, shear, and torsion capacities of steel angle sections.” J. Struct. Eng., 128(11), 1394–1398.
15.
Trahair, N. S. (2002b). “Moment capacities of steel angle sections.” J. Struct. Eng., 128(11), 1387–1393.
16.
Winter, G. ( 1968). “Thin-walled structures—Theoretical solutions and test results.” Preliminary Publications of the Eighth Congress, International Association for Bridge and Structural Engineering (IABSE), 101–112.
17.
Young, B., and Rasmussen, K. J. R. (1998). “Tests of fixed-ended plain channel columns.” J. Struct. Eng., 124(2), 131–139.
18.
Young, B., and Rasmussen, K. J. R. (1999). “Shift of effective centroid of channel columns.” J. Struct. Eng., 125(5), 524–531.
19.
Yu, W.W. ( 2000). Cold-formed steel design, 3rd Ed., Wiley, New York.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 ASCE.
History
Published online: Nov 15, 2004
Published in print: Dec 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.