Design of Cold-Formed Steel Channel Columns with Complex Edge Stiffeners by Direct Strength Method
Publication: Journal of Structural Engineering
Volume 130, Issue 11
Abstract
The design of cold-formed steel channels with complex stiffeners could be quite tedious in calculating the effective area using the effective width method in the current design rules of North American Specification and Australian/New Zealand Standard. The direct strength method could be used in the design without calculating the effective area. An experimental investigation of fixed-ended cold-formed steel channel columns with complex edge stiffeners has been reported. The test strengths were compared with design strengths predicted using the direct strength method as well as the North American Specification and Australian/New Zealand Standard for cold-formed steel structures. The failure modes observed in the tests were also compared with the failure modes predicted by the direct strength method. It is shown that the design strengths predicted by the direct strength method are generally conservative for the channel columns with complex edge stiffeners. Furthermore, the reliability of the direct strength method was evaluated using reliability analysis. It is shown that the direct strength method is reliable using the existing resistance factor as recommended by the current North American Specification and Australian/New Zealand Standard.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Iron and Steel Institute (AISI). (1996). Specification for the design of cold-formed steel structural members, Washington, D.C.
2.
American Society of Civil Engineers (ASCE). (1998). “Minimum design loads for buildings and other structures.” ASCE Standard 7-98, Reston, Va.
3.
Australian Standard (AS). (1989). “SAA loading code, Part 1: Dead and live loads and load combinations.” AS 1170.1-1989, Standards Association of Australia, Sydney, Australia.
4.
Australian Standard (AS). (1991). “Methods for tensile testing of metals.” AS 1391, Standards Association of Australia, Sydney, Australia.
5.
Australian Standard (AS). (1993). “Steel sheet and strip—hot-dipped zinc-coated or aluminium/zinc-coated.” AS 1397, Standards Association of Australia, Sydney, Australia.
6.
Australian/New Zealand Standard (AS/NZS). (1996). “Cold-formed steel structures.” AS/NZS 4600:1996, Standards Australia, Sydney, Australia.
7.
Canadian Standards Association (CSA). (1994). “Cold formed steel structural members.” S136-94, Rexdale, Ontario, Canada.
8.
Dinovitzer, A.S., Sohrabpour, M., and Schuster, R.M. (1992). “Observations and comments pertaining to CAN/CSA-S136-M89.” Proc., 11th Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, Mo., 551–569.
9.
Hancock, G. J., Murray, T. M., and Ellifritt, D. S. (2001). Cold-formed steel structures to the AISI specification, Marcel Dekker, New York.
10.
North American Cold-formed Steel Specification (NAS). (2001). North American specification for the design of cold-formed steel structural members, American Iron and Steel Institute, Washington, D.C.
11.
Papangelis, J. P., and Hancock, G. J. (1995). “Computer analysis of thin-walled structural members.” Comput. Struct., 56(1), 157–176.
12.
Schafer, B. W. (2000). “Distortional buckling of cold-formed steel columns.” August Final Rep. to the American Iron and Steel Institute, Washington, D.C.
13.
Schafer, B. W. (2002a). “Local, distortional, and Euler buckling of thin-walled columns.” J. Struct. Eng., 128(3), 289–299.
14.
Schafer, B.W. (2002b). “Progress on the direct strength method.” Proc., 16th Int. Specialty Conf. on Cold-Formed Steel Structures, Orlando, Fla., 647–662.
15.
Schafer, B.W., and Peköz, T. (1998). “Direct strength prediction of cold-formed steel members using numerical elastic buckling solutions.” Proc., 14th Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, Mo., 69–76.
16.
Yan, J., and Young, B. (2002). “Column tests of cold-formed steel channels with complex stiffeners.” J. Struct. Eng., 128(6), 737–745.
17.
Young, B., and Rasmussen, K. J. R. (1998). “Tests of fixed-ended plain channel columns.” J. Struct. Eng., 124(2), 131–139.
18.
Yu, W. W. (2000). Cold-formed steel design, 3rd Ed., Wiley, New York.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 ASCE.
History
Published online: Oct 15, 2004
Published in print: Nov 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.