Sensitivities of Strength and Ductility of Plated Reinforced Concrete Sections to Preexisting Strains
Publication: Journal of Structural Engineering
Volume 128, Issue 5
Abstract
Existing reinforced concrete (RC) beams are commonly enhanced in flexure by bonding steel or fiber-reinforced polymer (FRP) plates to their tension faces. At the time of plating, preexisting loads, such as dead loads, are present on the beams. Although these loads clearly do not induce strains in the plates, flexural capacity design calculations for plated beams using RC theory tacitly incorporate the corresponding fictitious preexisting strains in the plates. If the plates are elastic at section flexural failure, as might be the case for steel plates and is always the case for FRP plates, this design approach underestimates the area of plate required for a given increase in flexural capacity, thus giving a weaker plated RC section than required. For steel-plated sections in which both the internal steel and plate steel yield before concrete crushing occurs, preexisting strains do not influence the area of plate required, but they do delay yield and so reduce ductility. In such cases, neglect of preexisting strains does not affect strength, but it does lead to overestimate of available ductility. This has implications for design of statically indeterminate plated RC beams. Owing to uncertainties in parameters such as creep and differential settlement, preexisting strains do not lend themselves to accurate evaluation. Hence it seems prudent, as a first step, to establish the sensitivity of the flexural failure behavior of plated RC sections to varying preexisting strains. In this paper, mechanical models for plated RC section flexural behavior, which allow for steel and concrete material nonlinearities and for preexisting strains, are presented. The models are first verified by comparison with experimental data, and are then used to determine areas of FRP or steel plating required for stated flexural capacity increases of a given RC section, based on either ignoring or fully recognizing varying levels of preexisting strain. The moment-curvature characteristics, based on the models, of the latter plated RC sections are then presented, using the preexisting strains considered at the design stage. The results confirm that both the ductility and strength of plated sections are appreciably sensitive to preexisting strains. It is concluded that existing approaches for design of plating for RC members should take cognizance of these potentially debilitating effects of preexisting strains.
Get full access to this article
View all available purchase options and get full access to this article.
References
Arduini, M., and Nanni, A.(1997). “Behavior of precracked RC beams strengthened with carbon FRP sheets.” J. Compos. Constr., 1(2), 63–70.
Case, J., Chilver, L., and Ross, T. F. (1999). Strength of materials and structures, 4th Ed., Arnold, London, 31–32.
El-Mihilmy, M. T., and Tedesco, J. W.(2000). “Analysis of reinforced concrete beams strengthened with FRP laminates.” J. Struct. Eng., 126, 684–691.
Hutchinson, A. R., and Rahimi, H. (1993). “Behavior of reinforced concrete beams with externally bonded fibre reinforced plastics.” Proc., 5th Int. Conf. on Struct. Faults and Rep., ECS, Edinburgh, U.K., 221–228.
Jones, R., Swamy, N., and Ang, T.(1982). “Under- and over-reinforced concrete beams with glued steel plates.” Int. J. Cem. Comp. Lightweight Conc., 4(1), 19–32.
Jones, R., Swamy, R. N., and Charif, A.(1988). “Plate separation and anchorage of concrete beams strengthened by epoxy-bonded steel plates.” J. Struct. Eng., 66(5), 85–94.
Kishi, N., Mikami, H., Matsuoka, K., and Kurihashi, Y. (2001). “Failure of strengthened RC beams with AFRP sheets.” Proc., 5th Int. Symp. on Non-Metallic (FRP) Reinforcement for Concrete Struct., 1., C. J. Burgoyne, ed., Telford, London, 87–95.
Kotsovos, M. D.(1979). “A mathematical description of the deformational behavior of concrete under complex loading.” Mag. Concrete Res., 31(107), 77–90.
Luke, P. S., Leeming, M. B., and Skwarski, A. J. (199). “The use of advanced composites in strengthening existing structures and for new build.” Proc., 8th Int. Conf. on Structural Faults and Repair, ECS, Edinburgh, U.K.
Meier, U., and Kaiser, H. (1991). “Strengthening of structures with CFRP laminates.” Proc., ASCE Special Conf. on Adv. Comp. Mat. in Civ. Eng., Las Vegas, 224–232.
Sebastian, W. M.(2001). “Significance of midspan debonding failure in FRP-plated concrete beams.” J. Struct. Eng., 127(7), 792–798.
Swamy, N., Jones, R., and Bloxham, J.(1987). “Structural behavior of concrete beams strengthened by epoxy-bonded steel plates.” J. Struct. Eng., 65A(2), 59–68.
Takahashi, Y., Sato, Y., Ueda, T., Maeda, T., and Kobayashi, A. (1997). “Flexural behavior of RC beams with externally bonded carbon fibre sheets.” Proc., 3rd Int. Symp. on Non-Metallic (FRP) Reinforcement for Concrete Struct., 1, Japan Concrete Institute, Sapporo, Japan, 327–334.
Information & Authors
Information
Published In
Copyright
Copyright © 2002 American Society of Civil Engineers.
History
Received: Jul 7, 2000
Accepted: Oct 30, 2001
Published online: Apr 15, 2002
Published in print: May 2002
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.